Dispenser Care And Cleaning - GE Appliances Profile GXCF35GBS Owner's Manual

Errorcode:E1
Alarmwill soundand
displayE1 for 10seconds.
Theunitwill thenshut
downand display"OFF"
What Is Wrong
• Hot water tmlk exceeds
temperature limits.
• No/low water level in system.
What To Do
• Confim_ that water bottle installed is supplying water
to the system. Dispense hot water to release any trapped aiL
Mlow the refit to cool flw several hom_ Mtb the power off.
_Mter the unit cools, resume operation by pressing the
power b/itton.
Errorcode:E2
• Cold water tank too cold.
• Operating enviromnent too cold.
• Compartment door may be open.
• The system Mll automatically reduce cooling operation
to restore a correct temperature condition. Confixm that
the compartment door is closed. The control/display will
reset automatically when a nomml temperature has been
restored. Unplug the unit and allow it to wam_ up if the
problem persists. Relocate the dispenser to a warnler
operating environment if the error repeats. If a wam_er
operating environment is not a\;filable, increase the hot
wamr temperatm'e and operation time (with the Energy
Saver cycle set-up) to help offset this issue.
Errorcode:E3
• Compartment temperature
too cold.
• Operating enviromnent too cold.
• Extremely high cold water usage.
• Bottled water temperature high
when installed.
• The system Mll automatically reduce cooling operation
to restore the correct temperatm'e condition. Confima that
the compartment door is closed. The control/display will
reset automatically when nomml temperatm'e has been
restored. Mlow the bottle temperature to stabilize to room
temperature befin'e installation on the dispense_: Unplug
the refit and alh)w it to wmm up if the problem persists.
P.elocate the dispenser to a wam_er operating environment
if the error repeats.
Errorcode:E4,E5and E6
• Dispenser has experienced
a sensor failure,
• Unplug the refit fi)r 24 hom_ and allow the control to reset.
Plug the refit in and repeat start up and operation
adj ustments. Repeat if reqtfired; however, sore e fifilm'es
I/lav be pell/lanent.
Careand cleaning of the dispenser.
To remove To replace
(__upport collar
Separator
Cleaning the Separator
IMPORTANT" Unplug the water dispenser
before cleaning.
l. Remove the water bottle and drain the
dispenser
(see Draining the Dispenser).
2. Remove tim support collar by turning
counterclockwise and pulling straight off.
3. Remove the plastic separator bv
pulling straight out (you may need
to twist slightly to loosen).
4. Clean the separator with dish soap
and water or in the top rack of
the dishwasher.
5, Dry the separator thoroughly on
both sides,
6. Llsing a clean cloth or paper towel,
thoroughly dry the cold water
reselwoir.
7. Place the separator back in the
dispense_: Make sure the hmg, tapered
end of the separator is positioned
firmly on the metal plug on the
bottom of the reservoir;
8. Replace the support collar and turn
clockwise tmtil it is firmly in place.
9. Install a flfll water bottle on the
dispenser (see Loading the Dispenser).
Cleaning the Outside Cabinet and Storage/Chiller Compartment
IMPORTANT'. Unplugthe water dispenserbefore
cleaning.
The cabinet and compartment of the
dispenser can be washed with mild soap and
water: Rinse thorough b with clem" water: Never
use commercial cleanecs or abrasive scouring
pow(te_:_,
Sweep awa) or
\;tCtltlI/'l an}
dust from the
condenser coils on the back of the unit, For
best results, use a brush speciall} designed fi)r
this purpose, It is m_filable at most appliance
stoI'es,
9