Table of Contents
Advertisement
FS-8700-66 GE-SNP Driver Manual
No Message
21 GE_STAT_CONNECT_RESPONSE
22 GE_STAT_CONNECT_NO_RESPONSE
23 DRV_DLL_CLIENT_SENDS_MSG
24 DRV_DLL_CLIENT_SENDS_ACKNAK
25 DRV_DLL_CLIENT_SENDS_BYTES
26 DRV_DLL_SERVER_SENDS_MSG
27 DRV_DLL_SERVER_SENDS_ACKNAK
28 DRV_DLL_SERVER_SENDS_BYTES
29 DRV_DLL_CLIENT_RCVS_MSG
30 DRV_DLL_CLIENT_RCVS_BYTES
31 DRV_DLL_SERVER_RCVS_MSG
32 DRV_DLL_SERVER_RCVS_BYTES
33 DRV_DLL_TIMEOUT
34 DRV_DLL_ERROR
35 DRV_DLL_ERROR_CODE
36 GE_STAT_DRV_ACT_NODE_OFFLINE_R
37 GE_STAT_DRV_ACT_NO_MAPDESC_R
38 GE_STAT_DRV_ACT_NO_DATA_R
39 GE_STAT_DRV_ACT_NO_NODE_R
40 GE_STAT_DRV_ACT_NAK_R
41 GE_STAT_DRV_ACT_NORMAL_R
42 GE_STAT_CD_UPD_CHECK
43 GE_STAT_CD_UPD_FUNCTION
44 GE_STAT_CD_UPD_NO_START
45 GE_STAT_CD_UPD_PROTO
46 GE_STAT_CLIENT_SENDS_FRAG
47 GE_STAT_CD_UPD_IC_TIMEOUT
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com
Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com
Description
Counts the number of times the driver responds to connection
attempts when acting as a Server
Counts the number of connection attempts that timed out.
Counts the number of connection and poll messages sent by the Client
(whole messages only)
Counts the number of simple Ack/Nak's sent by Client. These
Ack/Nak's indicate messages if formatted correctly, but the device can
not necessarily respond to the request.
Byte count includes Ack/Nak's sent and all fragments and connection
Same as for Client
Counts ack/nak's, and all message fragments excluding attach
responses
Byte count from above messages
Counts message fragments and ack/nak's rcvd from Client but excludes
Client responses to Server fragments
Byte count for above messages
Count of timeouts caused by no response or ic_timeout at the DLL
layer
Count of the number of times that the DLL layer went into an error
state.
The error code from the most recent DLL error is stored here.
Corresponds to slave driver actions in responding to a poll. The polled
Node is offline.
Corresponds to slave driver actions in responding to a poll. There is no
Map Descriptor that can be used to process the poll from the Client.
Corresponds to slave driver actions in responding to a poll.
no data available.
Corresponds to slave driver actions in responding to a poll.
should never happen as a connection would have been refused.
The slave cannot respond to a poll for one of the reasons above.
The Server has responded to a poll normally
A message is invalid because the checksum failed.
A message is invalid because the message type is not known.
A message is invalid because it begins with the wrong codes.
A message is invalid because it is unexpected in its current context or
some other reason.
Counts the number of read/write message fragments sent by the
Client.
Counts the number of times that an IC timeout error occurred at the
DLL layer
Page 24 of 28
There is
This
Advertisement
Table of Contents
