Device; Programming The Remotecontrolto Operateyourotherdevices - Toshiba 57H93 Owner's Manual

Programming the remotecontrolto operateyourotherdevices
Device code setup
l. Refer to the multi-brand *'emote control device code table
on pages 32-33 to find the code for tbe brand of your
device.
If more than one code is listed, try each one separately until
you find the one that works.
2. Press MODE until the Mode indicator for the device
(CABLE/SAT, VCR, DVD, AUDIO 1, AUDIO 2) lights
up.
3. While holding down the RECALL button, press the
Channel Number buttons to enter the four-digit code for
your brand of device. Ira valid code is entered, the mode
indicator will blink twice. If an invalid code is entered, the
mode indicator will blink one long blink.
4. Point tbe remote control at tbe device and press POWER to
test the code.
[['the device respondsto the remote control."
You have entered the correct code.
{['the device doesnot respond to the remote control:
You may bave entered the wrong code. Repeat steps 3
and 4 using another code.
Note: le add/don toPOWER, corsfirm ti_at a llnecessary keys
ontheTVremote cont_d operate y ourdev/ceff somekeys
arenotoperat/onal, repeatthedevice codesetup using
another c ode(ffothercodes arelisted foryourdevice)
If,afZer t_y/ng a lllistedcodes, thenecessary keysdo not
ope/aze yourdevice, usethedevice's o ngina/ /emotecontrol
5. Press MODE to select the TV mode to control the TV.
Note:
• Aflhough the TVremo_ecoetro/lecludescodesfor manydevices,it may
not includecodesfor someor all of the featu/eson ce/talndevicesyou
wish to control ffyou areunable to prop/am the TVremote control to
opelaze your deviceor someof the featuleson that device,usetile
device'sremote controlor the controlson the device
• Ead_time you changeLhebatteries you will need to rep/ogramthe
remote contloL
• Somenewer VCRsrespond_oeither oftwo codes TheseVCRshavea
switchlabeled "VCRI/VCR2" ffyour VCRhas thisk_ndof switchand
doesnot/espond to the codesforyour VCRbrand,set the switchto Lhe
otherposit/on f,"VCR 1" or "VCR2") and/eprog/am the/emote control
Searching and sampling the code
of a device {8500}
lfyou do not know the device code for a particular device, you
can cycle the remote control tbrough tbe available codes tbr tbat
device mode and sample the functions to find the code tbat
operates the target device. The keys available to be sampled,
provided they are applicable to that mode, are POWER, 1,
VOL i CH i, and PLAY. Invalid keys will be ignored while in
program mode.
To cycle through each available device code and sample its
functions:
1. Press MODE to select the mode you want to set up.
2. While holding down RECALL, press 8 - 5 - 0 - 0.
The remote control will enter program mode.
3. Point the remote control at the target device and press
POWER (or other function buttons that are available to be
sampled).
4. If the device respondsto the remote control:
Press RECALL to store tbe device code. The mode
indicator will blink twice and tbe remote control will exit
tbe program mode.
If the device does not respond to the remote control:
Press &, and then press POWER.
Repeat this step until the device responds to tbe remote
control, and then press RECALL.
Note: Whena search cycleiscompleted, t hemode
/o&eator wfflbliekthreetimes Theremotecontr_lwill
beginto cyclethroughtheavailable codesagain fine key
/spressedwith/o10secondswbileprogrammingthe
remotecontrolwfflexittheprogrammodeandreturnto the
previous code
÷÷
:_' (_) _ _-- Numbers
®®®
-- VO k A/_'
N r_--'_ -- RECALL
30
Copyright © 2003 TOSHIBA CORPORATION All rights reserved