Frigidaire FFES3015LSE Use & Care Manual page 16

SETTING OVEN CONTROLS - MODEL A
To Set or Change the Temperature for
Baking
The oven can be programmed to bake at any
temperature from 170°F to 500°F (76°C to 260°C).
To Set the Controls for Baking:
1. Press BAKE pad. "---- o,, appears in the display.
2. Within 5 seconds, press the UP or DOWN ARROW
pad. The display will show "350°F." By pressing
and holding the UP or DOWN ARROW pad, the
temperature can then be adjusted in 5°F increments.
3. When the UP or DOWN ARROW pad is released,
the oven will begin heating to the selected
temperature. When the displayed temperature
reaches the desired baking temperature, the control
will beep once (1 time).
4. To cancel the baking function, press CLEAR OFF
pad.
To Change the Oven Temperature after Baking has
Started:
1. PressBAKE pad and make surethe bake
temperatureis displayed,
2. Press the UP or DOWN ARROW pad to increase or
decreasethe settemperature,
To Broi|
1. Arrange oven rack while oven is still cool.
2. Press BROIL pad.
3. Press and hold the UP or DOWN ARROW pad until
the desired broil setting level appears in the display.
Press the UP ARROW pad for HI broil or the DOWN
ARROW pad for LO broil. Most foods can be broiled
at the HI broil setting. Select the LO broil setting to
avoid excess browning or drying of foods that should
be broiled to the well-done stage.
4. Place the insert on the broiler pan, then place the
food on the insert. DO NOT use the broiler pan
without the insert or cover the insert with aluminum
foil. The exposed grease could ignite.
5. Place the pan on the oven rack. Open the oven door
to the broil stop position when broiling.
6. Broil on one side until food is browned; turn and cook
on the second side. Note: Always pull the rack out to
the stop position before turning or removing food.
7. When broiling is finished, press CLEAR OFF pad.
CAUTION
Should an oven fire occur, close the oven door
and turn off the oven. If the fire continues, use a
fire extinguisher, DO NOT put water or flour on
the fire, Flour may be explosive.
Adjusting Your Oven Temperature
Your new oven has been factory calibrated and tested
to ensure an accurate baking temperature. For the first
few uses, follow your recipe times and temperature
recommendations carefully, if you feel your oven is too
hot or too cool from your baking experience, the oven
temperature may be adjusted to your liking.
NOTE
DO NOT adjust your oven temperature based on oven
thermometers, such as those found in grocery stores,
they may not be accurate.
To Adjust the Oven Temperature (do not use Bake
or Broil while adjusting the oven temperature):
Note: Your oven control was factory set in the
(Fahrenheit) °F Temperature Display Mode. To change for
(Celsius) °C, see page 15,
1. Press & hold the BAKE key pad and release after the
display shows the factory temperature setting of 00.
Note: If the oven temperature has been previously
adjusted from the factory setting, the current
temperature adjusted value will appear in the display
instead.
2. "Youmay increase the oven temperature in 5°F (I°C)
increments with each press of the UP ARROW pad
to a maximum oven adjustment of +35°F (+18°C).
You may also adjust the oven temperature downward
in 5°F (1°C) increments with each press of the
DOWN ARROW pad (total range of -35°F to +35°F
(-18°Cto +18°C).
3. Ifyou do notwant to keep the display adjustment,
pressthe CLEAR OFF pad beforethe oven control
beeps,Thiswill cancelthetemperatureadjustment
procedure, To start thisprocedureoveragainbegin
with step1 above OR;
4. Ifyou want to keep the adjustment, waituntil t he
oven control beeps once.
5. The oven temperatureadjustmenthas be accepted
by the oven control and thedisplay will return to the
time of day.
Failure Modes
All failure modes give a visual and audible alarm. When
display shows FI0 (temperature runaway), F30-F31
(oven sensor circuit fault) or any other F error codes, the
electronic oven control has detected a fault condition.
Note that code and push the CLEAR OFF pad to clean
the display and stop the beeping. Reprogram the oven.
If fault recurs, push CLEAR OFF pad, disconnect the
appliance to prevent damage and contact an authorized
servicer.
16