Compu Link Remote Control System; Automatic Source Selection; Synchronized Recording - JVC RX-7030VBK Instructions Manual

COMPU LINK Remote Control System
The COMPU LINK remote control sys_rn allows you te operate JVCb audio components through the remote sensor on
the receiver.
'lb ase this remote control system, you need to connect JVC's audio
components t_rough the COMPU L1NK (SYNCHItO) jacks (see
below) in addition m the connacdons using cables with RCA Nn
plugs (see pages 12 and 13).
• Make sure that the AC power cords of these components are
u_pltlgged before connacdon. Plug tbe AC power co_ only _fftor
all connections are complete.
RX_7030VBK
RX-7032VSL
CD ilayer
I
Cassette deck
or
CD recorder
Notes:
• TherearefourvereioneofCOMPULINKremotecontreleyotem.
This receiver is equipped with the fourth versien--COMPU LINK-4.
This version is added systematic operations with the CD recorder to
the previous vereiun_COMPU LINK_3.
• ffyour audio component has two COMPU LINKjack_, you can use
either one. If it has only one COMPU LINK jack, connect it so that it
is the last item in the series of components,
• TeoperatethetargetcomponentueingtheCOMPULINKremote
control system, set the source name correctly ff required,
(See page 21.)
• Refer also to the manuals supplied with your audio components.
This remote control system allows you to use fo_rr functions listed
below.
Remote Control throuoh the Remote Sensor on the
Receiver
You c_m control the connected a_ldio components t_rougb the remote
sensor on the recelve:r using this remote control, Aim the remote
control directly at the remote sensor on Ihe receiver, For details,
see p_'_ges 44 and 45.
Automatic Source Selection
When you Fsess the play (1_) button on a connected component or
on its own remote control, the receiver aumm_icMly rams on and
changes the source to the component. On the other hand, if you
select a new' source on the reccivar or on the remote control, the
selacted component begins playing immediately'.
In both cases, the Fseviously selected sottrce continues playing
without sound for a few' seconds.
• FOrRX*7030VBKzTIX-TO32VSL: Y oucannot u_ the COMPU LINK
remote control system to Operatethe MD recorder.
Automatic Power On/Off [Standbvl--onlv oossibls with
the COMPU LINK-3 end COMPU LINK-4
l'be connected components mrn on andoff (standby) along with the
receiver,
When you turn on the reccivar, one of the connected components
will turn on automatically, depending on which component has been
previously selected.
When you mrn ot_"the receiver, the connected components will turn
off (standbg_,
S_vnchronized Recordino
Syncl_ronized recording means the c_sette deck (.orMD recmder)
starts recmding as soon as a CD begins playing,
'lb use synchrodized recording, follow these steps:
1. Put a tape in the cassette deck (or an _ in the
MD recorder), and a disc in the CD player.
2. Press the record (O) button and the pau_ (ll)
button on the eas_tte deck (or MD recorder) at
the same time.
This puts the cassette deck _cq" M D recordar) into recording
passe,
if you do not press the record (O) lmtton and pause
(11)
button at
the same time, the synchronized recmding feature wilI not
operate.
3. Press the play (1.-) button on the CD player.
The sottrce changes on the receiver, and as soon as play starts,
the cassette deck (or MD recordo_) starts recording. _en the
play ends, the cassette deck (o_"MD recorder) enters recording
passe, and stops about 4 seconds later.
Notes:
• During synchronized recording, the selected source cannot be
changed.
• Ifthepowerofanycomponentieehutoffduringeynehrenized
recording, the COMPU LINK remote control system may not
operate properly. In this case, you must start again from the
beginning,
41