Setting Dynamic Range; Attenuating The Input Signal; Input Analog; Midnight Mode - JVC RX-7030VBK Instructions Manual

2. Press INPUT DIGITAL (or ANALOG/DIGITAL
INPUT on the remote control) to select "DGTL
AUTO."
The DIGITALAUTO indicator
lights
up on the
display.
[_'-_'_j [',][_ u_,_:_j_]
[][][] i", i i r'_
[] [] l';gl rl .'.'l I"I ;l .... 25
• When selecting "DGTL AUTO," the following indicators
indicate the digital signal format of the incoming signal.
[LINEAR PCM]
[ DD
DIGITAL ]
[ a¢. ]
: Lights up when Linear PCM signals come
in.
: Lights up when Do[by Digital signals
come in.
: Lights up when DTS signals come in.
No indicator lights up when the receiver cannot recognize the
digital signal format of the incoming signals.
When playing software encoded with the Dolby Digital or DTS,
the following symptoms may occur:
• Sound does noi come out ai the beginning of playback.
• Noise comes out while sem'ching for or skipping chapters or
tracks.
In this case, press INPUT DIGITAL repeatedly to select _]
"DGTL D.D" or "DGTL DTS" while "DGTL AUTO"
still remains on the display.
• As you press INPUT DIGITAL, the input mode changes as
follows:
r_,_j [14 _! _
[33[?3[?3
,,," ' IF.,
[] [_ r'-, i-. i- i ¢", i i 'T" ¢",
- e5
F DGTL AUTO*m- DGTL D.D ta_]
(Digital) (Dolby Digi
* DGTL DTS +
When "DGTL D.D" or "DGTL DTS" is selected, the AUTO
indicator goes off, and the corresponding digital signal format
indicator lights up on the display.
• If the incoming signal does not match the selected digital signal
format, the frame of the selected indicator will fl&sh.
Note:
When you turn off the power or select another source, "DGTL 12D"
and "DG TL DTS" settings are canceled and the digital input mode is
automatically reset to "DGTL AUTO."
To select the analog input mode again
Press INPUT ANALOG (or press ANALOG/DIGITAL INPUT on
the remote control repeatedly until "ANALOG" appears on the
display). The ANALOG indicator lights up.
[] [] I =', I I r.
i il ii i
I-I k
i "3 i
I"I I"=" _I [_
I I I'I I I I-. '..' '..J _u.E
You can enjoy a powerful sound at night using the Midnight Mode.
ego
_====2
Press MIDNIGHT MODE so that "MID NIGHT 1" or "MID
NIGHT 2" appears on the display.
The MIDNIGHT MODE indicator also lights up.
MID NIGHT 1: Select when you want to reduce the dynamic
range a little.
MID NIGHT 2: Select when you want to apply the compress
effect fully (useful at midnight).
MID NIGHT OFF: Select when you want to enjoy surround with
its full dynamic range (no effect applied).
Notes:
• IfAna!og Direct is in use, Midnight Mode is temporarily canceled.
• MidnightModeisnotvalidforDVDMULTIplaybackmode.
When the input level of the analog source is too high, the sounds
will be distorted. If this happens, you need to attenuate the input
signal level to prevent the sound distortion.
• Once you have made adjustment, it is memorized for each analog
source.
L====A k=====J
Press and hold INPUT ATT (INPUT ANALOG) so that the
INPUT ATT indicator lights up on the display.
• Each time you press and hold the buiton, the input attenualor
mode turns on ("ATT ON") or off ("NORMAL").
Note:
This function is not valid when DVD MULTI is selected or when
Analog Direct is activated,
20