Present T Ime - GE GXSF18G Owner's Manual & Installation Instructions

Water softening system
Table of Contents

Advertisement

Available languages

Available languages

Optional Control Settings
The
controller
display
has sexeral
options
and teatures.
LOW SALT ALARM
I?__&_
The
LOW SALTALARM, when
enabled,
_
n
will somM
the beeper
when
the DAYS
_
4_)1 LIm
TO EMPTYxalue
is 15 da_s or less, To
chanoe,_ this setting,,
press
and
hold the MODEbutton
for
3 seconds.
ON
(e_ctorv
default)
or OFF will flash in the
display., Press the UP _
or DOX4N
buttons
to togole,
this feature
ON or OFF. Press the MODE button
to accept,
aim the displa)will
n/oxe
to SALT EFFICIENCY.
SALT EFFICIENCY
SALT
.EVEL
_4hen the SALT EFFICIENCY feamre
n
is ON, the refit will operate
at a salt
__
LII-I_ _
efficiency
of at least 4000 grains
of
hardness
remoxed
per p(mnd
of salt. This mode
of
operation
is the most
efficient
setting
for salt usa ,e
because
the s_steln
will tend
to recharge,
more
often,
with less salt usa._,e Turning,
the feature
OFF will tend
to lengthen
the time between
recharge
c) cles, which
will
proxide
the most
eiticient
usage
of water, but may use
more
salt. The degree
of difference
between
these
two c_cles is highly
dependent
on the water
usage
and
hardness
at a particular
installation.
If you haxe xer_ hard
water
and you find your s_stem
is reoenerating
exerv
1-2 days turn
the
SALTEFFICIENCY
to OFF to lengthen
the time between
regenerations.
NOTE: California
Regulations
require
tiffs feature
to be
(-)N for installations
in Califl)rnia.
To chanoe_.... the setting,
press tl_e LIP •
or D(A_N
buttons
to toggle
the feature
ON or OFF. Press the
MODE button
to accept.
The
displa)will
moxe
to
SYSTEM/ELECTRONIC DIAGNOSTICS.
SYSTEM/ELECTRONIC D IAGNOSTICS
This display
contains
s):stem
diagnostics
inflmnation
to assist in
troubleshooting
problems
with the
system.
See pages
15-18
fl)r details.
Press the MODEbutton
to return
to
the normal
mn display.
SALT
.EVaL
n
n
u
u
nnn
uuu
GEAppliances.com
LOST TIME SIGNAL
If time
is lost
on the
displa)
due
to power
interruption,
the
blue
indicator
light
will flash
4 times
exer_
second,
tmtil
the
present
time
of day is entered.
LOW SALT SIGNAL
When
the DAYS TO EMPTY drops
to 15, the blue indicator
light and
DAYS TO EMPTYin
the display
will flash
every
second
and
the alarm
will beep
every 30 seconds
(fl'om
8:00 AM to 8:00 PM), to notitV the user that the refit is
_mining
low on salt. As soon
as any button
is pressed,
the alam/will
stop beeping.
The
blue indicator
light and
DAYS TO EMPTYwill
continue
to flash.
Once
salt is added
to the brine
tank and the SALTLEVEL is reset,
the
DAYSTO
EMPTYwill
be reset.
ERROR SIGNALS
If there
is an error
code
detected,
the
I
blue indicator
light will flash 4 times
I
every second,
the display
will flash
Err
and the alarm
will beep
every 30 seconds
(from
8:00 AM
to 8:00 PM), to signal
that the sottener
requires
service.
The alarm
can be turned
off by pressing
any button,
but
the blue indicator
light and
display
will continue
to flash.
See page
16 tot inflmnation
to assist in troubleshooting
error
codes.
Once
the problem
is corrected,
disconnect
the
transfl)rmer
fl'om
the wall outlet
momentaril
B and I)lug it
back in. The
normal
display
will appear.
The
motor
may
um for several
minutes,
as the unit resets.
If the problem
is
not corrected,
the error
code
will real)pear
in 6 minutes.
BLUE INDICATOR LIGHT
Steady
blue light indicates
that
the unit is working
correctly.
The light flashes
when
the unit needs
attention
from
the user.
• i,ight
flashes
and
DAYS TO EMPTYflashes--check
salt lexel
and
add salt as required.
" I,ight
flashes
and
Err is in the displa)--electrical
problem
with system--see
page
16.
• I,ight will also flash when
power
to the unit
has been
interrupted.
Check
the
PRESENT T IME
setting.
11

Advertisement

Table of Contents
loading

Table of Contents