Download Print this page
GE GXSF40H Owner's Manual And Installation Instructions

GE GXSF40H Owner's Manual And Installation Instructions

Ge 40,000 grain water softener

Advertisement

Available languages

Available languages

GEAppliances.com

Safety Information

. . . . . . . . . . . . .2
Step-by-step instructions . . . . . . . .6-13

Operating Instructions

Breaking a salt bridge . . . . . . . . . . . . .15
venturi assembly . . . . . . . . . . . . . . . . . .15
Features . . . . . . . . . . . . . . . . . . . . . . . . . .16
Service . . . . . . . . . . . . . . . . . . . . .14, 17-19
Water softener system . . . . . . . . .14-19
. . . . . . . . . . . . .20
Consumer Support
Consumer Support . . . . . . . .Back Cover
Parts list/catalog . . . . . . . . . . . . . . .27-30
Warranty (U.S.) . . . . . . . . . . . . . . . . . . . .31
Warranty (Canada) . . . . . . . . . . . . . . . .32
System tested and certified by NSF International against NSF/ANSI Standard 44 for the
chemical reduction claims specified on the performance data sheet.
Sistema probado y certificado por NSF International contra norma 44 de NSF/ANSI para las
afirmaciones de reducción de los productos químicos especificadas en la hoja de datos de
funcionamiento.
System Tested and Certified by the Water Quality Association against CSA B483.1.
Sistema probado y certificado por Water Quality Association en cumplimiento con CSA B483.1.
Write the model and serial
numbers here:
Model # ________________
Serial # ________________
To find these numbers, lift the
cover and look on the rim
below the control panel.
Water Softening
. . . .3-13
Sistema Suavizante
. . . . . .21-23
7308726
215C1173P019
System
Owner's Manual &
Installation Instructions
Model GXSF40H
de Agua
Manual del Propietario e
Instrucciones de Instalación
Modelo GXSF40H
La sección en español empieza en la página 33
49-50176-3 03-09 JR

Advertisement

Chapters

loading

Summary of Contents for GE GXSF40H

  • Page 1: Table Of Contents

    GEAppliances.com Safety Information Water Softening ... . .2 Installation Instructions ..3–13 System Step-by-step instructions ..6–13 Operating Instructions Owner’s Manual & Breaking a salt bridge .
  • Page 2: Safety Precautions

    Do not attempt to treat water over 100°F. of the resin. In these conditions, you may wish to consider purchasing a GE point-of-entry household ■ Do not install in direct sunlight. Excessive sun or filtration system with a chlorine reducing filter.
  • Page 3 Installation Water Softening System Instructions Model GXSF40H Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca WARNING: Read entire manual. Failure to follow all guides and rules could cause personal injury or property damage.
  • Page 4: Unpacking And Inspection

    • If additional drain hose is needed for valve and salt tank drains, it can be ordered from GE Parts at 800.626.2002, part number WS07X10004. • If a rigid valve drain is needed to comply with plumbing codes, you can buy the parts needed to connect a 1/2″...
  • Page 5: Installation Instructions

    Installation Instructions PLAN HOW YOU WILL INSTALL THE WARNING: Use only lead-free solder and SOFTENER flux to prevent lead poisoning. You must first decide how to run in and out pipes See Typical Installation Illustration. Use this as a guide to the softener.
  • Page 6 Installation Instructions BEFORE YOU BEGIN MOVE THE SOFTENER ASSEMBLY INTO INSTALLATION POSITION • Turn off the gas or electric supply to the water heater, in the possibility that the water heater Before sliding softener in position, be sure the may be drained while draining pipes. installation surface is level and smooth.
  • Page 7 IMPORTANT: If more drain hose is needed, it should be ordered from GE Parts at 800.626.2002, part number WS07X10004. The water softener Turn bypass will not work if water cannot exit this hose valve upside during recharge.
  • Page 8 Installation Instructions CONNECT AND RUN THE VALVE INSTALL THE BRINE TANK DRAIN HOSE OVERFLOW FITTINGS AND HOSE (CONT.) • Elevating the drain hose may cause back • Insert the rubber grommet into the 3/4″ diameter pressure that could reduce the brine draw during hole in the brine tank sidewall as shown.
  • Page 9 Installation Instructions INSTALL GROUNDING CLAMP FLUSH PIPES, EXPEL AIR FROM SOFTENER AND TEST YOUR DANGER: INSTALLATION FOR WATER Failure to properly attach ground clamp could result in electrical shock. LEAKS (CONT.) If plumbing is metal, to maintain electrical ground • Place bypass valve in the “service” position continuity in the house cold water piping, install the EXACTLY as follows.
  • Page 10: Programming The Control

    Installation Instructions CONNECT TO ELECTRICAL POWER To gain access to the transformer/power cord assembly, remove the salt hole cover from the softener. Unclip the tabs on the rear of the top cover and rotate the cover upward to remove. DO NOT PULL OR DISCONNECT WIRING.
  • Page 11 Installation Instructions SET WATER HARDNESS NUMBER SET SALT LEVEL (CONT.) 3. When the display shows your water hardness 1. Press the MODE button SALT LEVEL (in grains per gallon), press MODE to accept. until arrow points to SALT LEVEL. NOTE: If there is clear water iron in your water supply, you will need to increase the hardness 2.
  • Page 12 Installation Instructions OPTIONAL CONTROL SETTINGS SIGNALS The controller display has several options and LOST TIME SIGNAL features. If time is lost on the display due to power LOW SALT ALARM interruption, the blue indicator light will flash 4 SALT LEVEL times every second, until the present time of day The LOW SALT ALARM, when is entered.
  • Page 13 Installation Instructions SANITIZING PROCEDURES To complete the installation, do the following water softener, and out the drain. This process sanitizing procedures. takes approximately 2 hours. Care is taken at the factory to keep your water 4. If, after sanitization, water from the house softener clean and sanitary.
  • Page 14 About the water softener system. Service When the water softening system is providing After a period of time, the resin beads become soft water, it is called “Service.” During service, coated with hard minerals and they have to be hard water flows from the house main water pipe cleaned.
  • Page 15: Breaking A Salt Bridge

    GEAppliances.com Breaking a Salt Bridge Sometimes, a hard crust or salt bridge forms in Push tool into salt bridge to break the salt storage area. It is usually caused by high humidity or the wrong kind of salt. When the salt bridges, an empty space forms between the 1″–2″...
  • Page 16: Features

    About the water softener system. Normal Operation, Control Displays During normal operation, the present time of day and AM or PM and DAYS TO EMPTY show in the control display area. When the demand computer determines a recharge is needed, RECHARGE TONIGHT begins to flash in the display along with the present time.
  • Page 17 GEAppliances.com Service: Electronic Demand Time Features and Service ERROR CODE DISPLAYED ERR 01 ERR 02 ERR 03 ERR 04 ERR 05 POSSIBLE DEFECT • Motor •Position •Motor •Position •Control inoperative switch inoperative switch or or wiring wiring harness harness • Wiring •Control •Control •Control...
  • Page 18: Service

    About the water softener system. Service: Manually Initiated Electronics Diagnostics 1. To enter diagnostics, press and hold – If there is no reading in the display, with faucet open, SALT LEVEL the MODE button for 3 seconds until check the sensor. Pull the sensor from the valve outlet the Low Salt Alarm screen shows.
  • Page 19 GEAppliances.com Service: Manually Advance Recharge Check NOTE: The control display must show a steady NOTE: If water system pressure is low, an time (not flashing). elevated drain hose may cause back pressure, stopping brine draw. 1. Press the RECHARGE button and hold in for three seconds.
  • Page 20: Care And Cleaning

    ® ® to help keep the resin bed clean of clear iron. If your water supply has clear water iron, periodic resin bed cleaning is needed. GE recommends using Super Iron Out brand resin bed cleaner ® to thoroughly clean your resin bed if your iron content is high.
  • Page 21: Troubleshooting Tips

    • Hardness setting too low. Check hardness setting and adjust. Verify hardness of supply water—from local water company, water test or call the GE Answer Center. • Salt Bridge—salt solidifies above water level so that brine water is not in contact with salt.
  • Page 22: Before You Call For Service

    Before you call for service… Troubleshooting Tips Problem Possible Causes What To Do Water hard sometimes Using hot water while the water • Avoid using hot water during water softening system softening system is regenerating recharge because the water heater will refill with hard water. See Automatic Hard Water Bypass During Recharge section, page 14.
  • Page 23 GEAppliances.com Problem Possible Causes What To Do Salty tasting or Unit not sanitized • Complete the Sanitization Procedures on page 13. brown/yellow colored • At completion of recharge cycle (approx. 2 hrs), run water water after installation from faucets to purge the salty water. Low water pressure Check pressure.
  • Page 24 Notes.
  • Page 25 Notes. GEAppliances.com...
  • Page 26 Notes.
  • Page 27: Parts List/Catalog

    Parts list. GEAppliances.com...
  • Page 28 Parts list.
  • Page 29 Parts catalog. GEAppliances.com GENERAL ELECTRIC PARTS CATALOG REF. NO. PART NO. PART DESCRIPTION (03) 0003 WS35X10001 O-RING SEAL KIT 0004 WS34X10015 DECAL, FACEPLATE 0005 WS07X10004 HOSE, DRAIN, 20 FT. 0006 WS31X10044 FILTER SCREEN 0007 WS14X10002 DISTRIBUTOR, TOP 0008 WS14X10001 DISTRIBUTOR, BOTTOM 0009 WS01X10002 RESIN, 1 CU.
  • Page 30 Parts catalog. GENERAL ELECTRIC PARTS CATALOG REF. NO. PART NO. PART DESCRIPTION (03) 0111 WS19X10005 SUPPORT SCREEN 0112 WS03X10013 SCREEN 0113 WS22X10020 FLOW PLUG, .10 GPM 0114 WS08X10005 GASKET & ASPIRATOR 0115 WS03X10015 CONE SCREEN 0116 WS22X10021 PLUG, FILL FLOW, .30 GPM 0117 WS03X10017 FERRULE NUT...
  • Page 31 This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location for service.
  • Page 32 Any part of the Water Softening System which fails due to a defect in materials or workmanship. From the date of the During this limited one-year warranty, GE will also provide, free of charge, all labor and related original purchase service to replace the defective part.
  • Page 33 Información de seguridad ..34 Instrucciones de instalación ....35–45 Instrucciones paso por paso ..38–45 Instrucciones de operación Cómo limpiar la ensambladura de la boquilla y el Venturi .
  • Page 34 En estas condiciones, es posible que quiera distorsión u otros daños a las partes no metálicas. considerar la compra de un sistema de filtración del punto de admisión para casas GE con un filtro ■ Conecte a tierra de manera apropiada según los reductor de cloro.
  • Page 35: Instrucciones De Instalación

    Sistema Suavizante de Agua de instalación Modelo GXSF40H ¿Preguntas? Llame 800.GE.CARES (800.432.2737) o Visite nuestra página en la red en: GEAppliances.com ADVERTENCIA: Lea este manual en su totalidad. No seguir todas las pautas y normas podría causar lesiones personales o daños a la propiedad.
  • Page 36 • Si una manguera adicional es necesaria para el drenaje de la válvula y el tanque de sal, usted la puede solicitar en Accesorios GE llamando al 800.626.2002, no. de parte WS07X10004. • Si necesita una válvula rígida de drenaje para cumplir con los códigos de plomería, podrá...
  • Page 37 Instrucciones de instalación PLANIFIQUE LA INSTALACIÓN ADVERTENCIA: Use solamente fundente DEL DESCALCIFICADOR y soldadura sin plomo para evitar envenenamiento de plomo. Lo primero que debe decidir es cómo instalar las tuberías que entran y salen del descalcificador. Fíjese en la tubería de agua Consulte la Ilustración de instalación normal.
  • Page 38 Instrucciones de instalación ANTES DE COMENZAR MUEVA LA ENSAMBLADURA DEL DESCALCIFICADOR HACIA SU POSICIÓN • Suspenda el suministro de gas o de energía eléctrica que alimenta el calentador de agua, en la posibilidad de que DE INSTALACIÓN el calentador pueda drenarse mientras usted drena las Antes de deslizar el descalcificador a su lugar, cerciórese de tuberías.
  • Page 39 Cerciórese de cumplir con los códigos locales. abajo como se muestra. IMPORTANTE: Si necesita más manguera de drenaje, ordénela llamando al Departamento de Partes de GE al 800.626.2002, no. de parte WS07X10004. El descalcificador Gire la válvula de agua no funciona si el agua no escapa por esta de bypass boca manguera durante las regeneraciones.
  • Page 40 Instrucciones de instalación CONECTE Y HAGA FUNCIONAR LA INSTALE LOS ACCESORIOS DE MANGUERA DE DRENAJE DE LA VÁLVULA SOBREFLUJO DEL TANQUE DE SALMUERA Y LA MANGUERA (CONT.) • Elevar la manguera de drenaje podría causar una • Inserte una arandela de goma en el agujero de 3/4″ presión negativa que podría reducir la toma del contenido (1,91 cm) de diámetro en el lado del tanque de salmuera de sal durante las regeneraciones.
  • Page 41 Instrucciones de instalación INSTALE LA ABRAZADERA DE TIERRA PURGUE LAS TUBERÍAS, SAQUE EL AIRE DEL DESCALCIFICADOR Y PRUEBE SU PELIGRO No adherir apropiadamente la INSTALACIÓN EN BÚSQUEDA DE FUGAS abrazadera de tierra podría resultar en una descarga DE AGUA (CONT.) eléctrica.
  • Page 42 Instrucciones de instalación CONECTAR A LA FUENTE ELÉCTRICA Para lograr acceso al transformador/ensambladura del cable eléctrico, remueva la cubierta del agujero de sal del descalcificador. Desengrape las orejillas en la parte posterior de la cubierta superior y rote la cubierta hacia arriba para remover.
  • Page 43 Instrucciones de instalación AJUSTE EL NIVEL DE DUREZA DEL AGUA AJUSTE EL NIVEL DE SAL (CONT.) 1. Presione el botón MODE 3. Cuando la pantalla muestre el nivel de dureza del agua SALT LEVEL (modo) hasta que la flecha deseado (en granos por galón), oprima MODE (modo) señale SALT LEVEL (nivel para aceptar.
  • Page 44 Instrucciones de instalación AJUSTES OPCIONALES DE CONTROL SEÑALS La pantalla del controlador ofrece varias opciones y SEÑAL DE HORA PERDIDA características. Si la hora se pierde en la pantalla debido a una interrupción ALARMA DE BAJO NIVEL DE SAL SALT en el suministro eléctrico, la luz indicadora azul se enciende LEVEL La LOW SALT ALARM (alarma de bajo...
  • Page 45 Instrucciones de instalación PROCEDIMIENTOS DE DESINFECCIÓN través del descalcificador de agua. Este proceso dura aproximadamente 2 horas. Para completar la instalación, siga los procedimientos de desinfección siguientes. 4. Si después de la desinfección, el agua de la llave de la casa tiene un sabor salado o tiene un color ligero, esto es un En la fábrica se siguen los cuidados para mantener preservativo del tanque de resina.
  • Page 46 Sobre el sistema de descalcificación de agua. Servicio Después de un período de tiempo, la capa de Cuando el sistema descalcificador de agua está resina se obstruye o se satura con los minerales proporcionando agua descalcificada, a esto se le duros y debe limpiarse.
  • Page 47: Cómo Romper Un Puente De Sal

    GEAppliances.com Cómo romper un puente de sal Empuje el instrumento hacia el interior del A veces, una capa dura de sal o puente de sal depósito de sal para se forma en el área de almacenamiento de la sal. romper el puente Esto generalmente se debe a la humedad alta o 1″–2″...
  • Page 48 Sobre el sistema de descalcificación de agua. Cómo limpiar la ensambladura de la boquilla y el Venturi Es necesario que la boquilla y el Venturi estén limpios para que el sistema de descalcificación Tapa de agua funcione apropiadamente. Esta pequeña unidad ejecuta la succión para mover la salmuera del área de almacenamiento de sal Sello del hacia el tanque de resina durante la recarga.
  • Page 49 GEAppliances.com Operación normal, Pantalla de control Durante la operación normal, la hora actual con la hora actual. RECHARGE TONIGHT del día y AM o PM y DAYS TO EMPTY (días hasta (recargue esta noche) parpadea hasta el vacío) se muestra en el área de la pantalla de momento de inicio de la próxima recarga, control.
  • Page 50 Sobre el sistema de descalcificación de agua. Servicio: Funciones y servicio del tiempo de demanda electrónico CÓDIGO DE ERROR VISUALIZADO ERR 01 ERR 02 ERR 03 ERR 04 ERR 05 POSIBLE DEFECTO • El motor no •Interruptor •Motor no •Interruptor •Control funciona de posición...
  • Page 51: Servicio

    GEAppliances.com Servicio: Diagnóstico electrónico iniciado manualmente 1. Para entrar a la función de diagnóstico, • Medidor del agua – Indica si el agua fluye a través SALT LEVEL de la válvula. oprima y mantenga oprimido el botón MODE (modo) por tres segundos hasta Motor que aparezca la pantalla de Low Salt Alarm (alarma de bajo nivel de sal).
  • Page 52: Sistema De Descalcificación

    Sobre el sistema de descalcificación de agua. Servicio: Configurar el código del modelo (F o H) 1. Para cambiar o revisar el código del modelo, 4. Presione el botón MODE (modo) una vez presione primero y sostenga el botón MODE para regresar a la operación y visualización (modo) por tres segundos hasta que aparezca normal.
  • Page 53: De Agua

    (llamada agua rojo ladrillo). Para extraer el hierro de esta agua se requiere un filtro u otro equipo. GE recomienda que se usen las marcas de sal Diamond Crystal Red•Out con aditivo Iron ®...
  • Page 54: Consejos Para La Solución De Averías

    Verifique la dureza del suministro de agua—llamando a su compañía de agua local, haciendo pruebas al agua o llamando al Centro de Respuestas de GE. • Puente de sal—la sal se solidifica por encima del nivel del agua de forma tal que la salmuera no está...
  • Page 55 GEAppliances.com Problema Posible causa Qué hacer A veces el agua Usar agua caliente mientras el • Evite usar agua caliente mientras el descalcificador de agua está está dura descalcificador de agua está en en el proceso de recarga porque el calentador de agua se el proceso de regeneración rellenará...
  • Page 56 Antes de llamar para solicitar servicio… Problema Posible causa Qué hacer Nivel alto/excesivo La válvula de drenaje de la manguera está • Cualquier restricción en la manguera de drenaje podría evitar la de agua en el tanque doblada y eso la está obstruyendo, o está operación apropiada de la boquilla y el Venturi y reduce o evita de la salmuera demasiado elevada, o su flujo está...
  • Page 57 Notas. GEAppliances.com...
  • Page 58: Lista De Partes/Catálogo

    Lista de partes.
  • Page 59 GEAppliances.com...
  • Page 60 Catálogo de partes. CATÁLOGO DE PARTES DE GENERAL ELECTRIC NO. REFER. NO. DE PARTE DESCRIPCIÓN DE LA PARTE (03) 0003 WS35X10001 KIT DEL SELLO DEL ARO TÓRICO 0004 WS34X10015 ETIQUETA, PLACA FRONTAL 0005 WS07X10004 MANGUERA DE DRENAJE, 20 PIES 0006 WS31X10044 PANTALLA DE FILTRO 0007...
  • Page 61 GEAppliances.com CATÁLOGO DE PARTES DE GENERAL ELECTRIC NO. REFER. NO. DE PARTE DESCRIPCIÓN DE LA PARTE (03) 0103 WS21X10003 INTERRUPTOR 0104 WS03X10009 PASADOR, EXPANSIÓN 0105 WS02X10014 TORNILLO 0106 WS31X10006 CUBIERTA DE LA VÁLVULA 0107 WS03X10010 RESORTE DE ONDA 0108 WS26X10002 ROTOR Y DISCO 0109 WS19X10004...
  • Page 62 Estados Unidos. Si el producto está situado en un área que no dispone de servicio por parte de un proveedor de servicio autorizado de GE, podría tener que hacerse cargo de los costes de envío o bien podría solicitársele que lleve el producto a un centro de servicio de GE autorizado para realizar la reparación.
  • Page 63: Soporte Al Consumidor

    Propietarios o pedir piezas en línea. Solicite una reparación GEAppliances.com El servicio de expertos GE está a tan sólo un paso de su puerta. Llame al 800.GE.CARES (800.432.2737) durante horas normales de oficina para solicitar su reparación. Real Life Design Studio (Estudio de diseño para la vida real)
  • Page 64 Contact Us GEAppliances.com If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including your phone number, or write to: General Manager, Customer Relations...

This manual is also suitable for:

Gxsf4oh