Page of 64

Advertisement

IMPORTANTSAFETYINFORMATION.
READALL INSTRUCTIONSBEFORE USING.
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of electric shock,
property damage or personal injury.
SAFETY P RECAUtiONS
_: Check
and
conq)ly
with vour state and
local
codes.
You must
fl)llow ti_ese guidelines.
::Ji:: Use care when
handling
the water
sotiening
s_:stem. Do not tm'n upside
down,
drop,
drag
or set on sharp
protrusions.
_: Water
sotiening
systems
using
sodimn
chloride
(salt)
for recharge
add
sodimn
to the water.
Persons on sodium restricted diets should consider
the added sodium as part of their overall intake.
Potassium chloride can be used as an alternative
to sodium chloride in your softener
Tile _sater softening
system _sorks on 24 _olt,60 Hz
electrical power only. Be sure to use only the
included transformer
_: Use clean water
softening
salts only, at least
99.5%
pm'e.
NUGGET,
PEI,I,ET
or coarse
SOLAR
salts are recommended.
Do not tlse rock,
block,
granulated
or ice cream
making
salts.
They
contain
dirt and
sediments,
or mush
and
cake, and will create
maintenance
problems.
::Ji:: Kee I) the salt hole cover in place
on the softener
tmless
servicing
the trait or refilling
with salt.
_, WARNING:
Do.o,
use with water that is
microbiologically
tmsat_" or el unknown
quality
without
adequate
disinfection
beti)re
or atier
tile system.
iJi:: T ransformer
must
be )luo,_ed
into
indoor
120 "_olt, grotmded
outlet
only.
PROPER INSTALLAtiON
This water softening system must be properly installed and located in accordance
with the Installation
Instructions before it is used.
?_: Install
or store
where
it will not
be
exposed
to
temperatures
beh)w
fl'eezing
or exposed
to any
type
of weather:
Water
fl'eezing
in tile system
will
break
it. Do
not
attempt
to treat
water
over
I O0°E
::Ji:: O 0 n0tinstall
in direct
s/mlight,
Excessive
sun
or
heat
may
catlse
distortion
or other
damage
to
non-metallic
parts.
Properly
ground
to cent)tin
with
all governing
codes
and
ordinances.
Use only lead-free
solder and flux for all sweat-
solder
connections,
as required
by state and
federal
codes.
_: Softener
resins may degrade
in tile presence
of chlorine
above
1 ppm.
If you have chlorine
in excess of this alnount,
you inay experience
reduced
life of tile resin.
In these
conditions,
you may wish to consider
pro'chasing
a (;E
i)oint-ofent_y
household
filtration
system with
a chlorine
reducing
filte_:
A WARNING: Disc.,d .lluilused pax'ts
and packaging
material
alter
installation.
Small parts
remaining
after
the installation
could
be a choke
hazard.
The water softening
s}:stem requires
a minimmn
water flow of three
galhms
per minute
at the inlet.
Maximum
allowable
inlet water pressm'e
is 125 psi.
]f daytime
pressure
is over 80 psi, nighttime
pressm'e
may exceed
the maximmn.
Use a pressm'e
reducing
wdve to reduce
the flow if necessarx:
READ ANDFOLLOW THIS SAFETY I NFORMAtiON CAREFULLY.
SAVETHESE INSTRUCTIONS
2

Advertisement

Comments to this Manuals

Symbols: 0
Latest comments: