Page of 64

Advertisement

Programmingthe Control
SALT
ll_l'l_lFi
I_
SALTLEVEL
L_WL
i U'U U
PM
PRESENTTIME
DAYS
TO
EMPTY
I I t I_
HARDNESS
--t C!
RECHARGE
_-
TIME
®
®
CONTROL
SETTINGS
RFQU1RED
upon
installation
and after an extended
power
outage.
NOTES:
::A:: WHEN
THE
TRANSFORMER
IS PI,UGGED
INTO
THE
EI,ECTRICAI,
OUTI,ET,
12:00
PM
(flashing),
and
an arrow
1_ is displayed
next
to
PRESENTTIME
on
the
taceplate
decal.
The
blue
indicator
light
will
also
flash.
Program
the
control
as instructed
below.
ff
I
If LOO---is
flashing,
use
theUP
button
to set
the
correct
F code
as tollows:
F18 fin" GXSFI
8(;.
If you
pass
by the
correct
code
nmnber,
use
the
DOWN
button.
Then
press
the
MODE button
to accept
the
correct
model.
;,'_: A "beep"
sounds
while pressing
buttons
fl)r control
programming,
One
beep
signals
a change
in the
control
display,
Repeated
beeps
mean
the control
will not accept
a change
fi'om
the button
you have
pressed,
and you should
select
another
button.
iA:: T o program
the control
you will rise the UP • ,
DOWN
and
MODEbuttons.
7_:Use the MODE button
to scroll arrow
I_ to desired
control
_'ilnction.
SET PRESENT TIME OF DAY
I. Press the MODE bumm until
arrow I_ points to PRESENT
TIME.
Z Press UP •
or DO'AN
button
to set. The
LrP button
adwmces
the time;
the DOWN
button
moves
the time
in
reverse.
If the present
time is between
noon
and midnight,
be sure
PM shows in the display.
If the present
time
is between
midnight
and
noon,
be sure AM shows in
the display.
NOTE:Each
press
of an UP •
or DO_._N
button
chanoes_
the time by one minute.
Holding
the button
changes
the
time at a rapid
rate.
3. When
the present
time is correct,
press
MODE to accept.
GEAppliances.com
SET WATER HARDNESS NUMBER
_,_
_
I. Press the MODE button
tmtil
_ HARDNESS
arrow
I_" points
to HARDNESS.
2. Press UP •
or DO'AN
button
to set wmr water
hardness
number
in the display.
DOWN
decreases
the hardness
value.
ILrP increases
the hardness
vahle.
NOTE:Each press
of a button
changes
the display
by 1,
between
1 and
25. Above
25, the display
changes
5 at a time
(25, 30, 35, etc.).
Holding
a button
in changes
the nulnbei_
at a rapid
rate.
3. When
the display
shows yore" water hardness
(in grains
per galhm),
press
MODE to accept.
NOTE:If there is clear water iron in your water
supply,
you will need
to increase
the hardness
setting
by 5 for
each
1 ppm
of clear water iron in your water supply.
You cml get the grains
per gallon
(gpg) hardness
of your
water
supply
from
a water analysis
laboratory.
If you are
on a municipal
supply,
call your local water
department.
Or call Legend
Technical
Services,
an independent
laboratory,
to request
a water
hm'dness
test kit at
1.800.826.8553,
extension
47. If your report
shows
hardness
in paaets per million
(ppm)
or milligrams
per liter
(mg/1),
simply
divide
by 17.1 to get the equivalent
number
of grains
per gallon.
SET RECHARGE(STARTING) TIME
I. Press the MODE bumm until
arrow _ points to RECHARGE
TIME.
AM
....
-i,n n
.....
C'U U
I_
RECHARGE
TIME
NOTE:A flashing
2:00 AM (factory
defimlt)
should
show in
the display.
This is a good
time for recharge
to start
(rakes
about
2 hours)
in Inost
households
because
water
is not
in use. HARD _._;__TER is bypassed
to house
fimcets
during
recharge.
If no chm_ge
is needed,
go to step 3. To change
the
recharge
starting
time,
ti)llow step 2.
2. Press UP •
or DO'AN
button
to set the desired
recharge
start time,
Be sure
to observe
the AM or PM
as you did when
setting
the time
of day.
NOTE:Each press
of a button
changes
the time bv 1 hour.
Holding
the buttons
in changes
the time at a rapid
rate.
3.
Press the MODE button
to accept.

Advertisement

Comments to this Manuals

Symbols: 0
Latest comments: