Image 10.0 User Manual page 11

Imtl39620
Hide thumbs Also See for 10.0:
Table of Contents

Advertisement

HOW TO TURN ON THE POWER
_11 Plug in the power cord (see page 9).
B
Stand on the foot rails of the treadmill.
I_
ind the clip attached to the key (see the drawing
on page 10), and slide the clip onto the waistband
of your clothes. Next, insert the key into the con-
sole. After a moment, the displays and various in-
dicators will light. Test the clip by carefully
tak-
ing a few steps backward
until the key is
pulled from the console.
If the key is not
pulled from the console,
adjust the position
of
the clip.
HOW TO USE THE MANUAL MODE
1
Insert the key fully into the console.
See HOW TO TURN ON THE POWER above.
B
Select the manual mode.
When the key is in-
serted, the manual
mode will be selected
and the Manual Control
indicator will light. If a
program has been
selected, press the Mode button repeatedly to res-
elect the manual mode.
_
ress the Start button or the Speed/'_ button to
start the walking belt.
A moment after the but-
ton is pressed, the
I
walking belt will begin to
/'-_. 5
I
move. Hold the
SPEED
handrails and begin
walking. As you exer-
cise, change the speed of the walking belt as de-
sired by pressing the Speed buttons.
![!
Each time a button is pressed, the speed setting
will change by 0.1 mph; if a button is held down,
the speed setting will change in increments of 0.5
mph. Note: The console can display speed and
distance
in either miles or kilometers
(see
SPEED DISPLAY on page 12). For simplicity,
all
instructions
in this section refer to miles.
To stop the walking belt, press the Stop button.
The Time display will begin to flash. To restart the
walking belt, press the Start button or the Speed/,
button.
Note: The first time you use the treadmill, periodi-
cally inspect the alignment of the walking belt, and
align it if necessary (see page 23).
Change the incline
of the treadmill
as desired.
To change the incline of the treadmill, press either
of the Incline buttons until the desired incline level
is reached.
B
ollow your progress
with the LED track and
the displays.
The LED Track--When
the manual mode or the
iFIT.com mode is se-
lected, the LED display
will show a track repre-
senting 1/4 mile. As you
exercise, the indicators
°eeeee°
eooooo@
eoooooe
ooooooe
oooee@o
around the track will light in sequence until you
have completed 1/4 mile. A new lap will then
begin.
Calories/Fat
Calories/
Pulse display--This
dis-
PULSE
o I / I-I 113
play shows the approxi-
FAT O
LI
mate numbers of calories
CALORIES
and fat calories you have
burned (see FAT BURN-
ING on page 24). The display will change from
one number to the other every few seconds. The
FAT indicator will light when the number of fat
calories is shown. The display will also show your
heart rate when you use the pulse sensor (see
step 6 on page 12).
11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 10.0 and is the answer not in the manual?

Questions and answers

Nicole Prisby
April 7, 2025

Powers on but displays multiple 8s and belt died not move

1 comments:
Mr. Anderson
April 9, 2025

If the Image 10.0 treadmill powers on but displays multiple 8s and the belt does not move, it likely indicates that the console is in a diagnostic or reset mode, or that it is not receiving proper input from internal components. Try the following steps:

1. Remove the key and unplug the power cord.
2. Reinsert the key fully into the console.
3. If the treadmill still does not run, check the alignment and gap of the Reed Switch and Magnet as described in the speed display troubleshooting section.
4. If the problem persists, contact Customer Service.

This answer is automatically generated

Subscribe to Our Youtube Channel

This manual is also suitable for:

Imtl39620

Table of Contents

Save PDF