Table of Contents
Advertisement
Programming
The Universal Remote Control
VCR
Cable Converter
Box
Preferred Procedure - Code Known
Preferred Procedure
- Code Known
Programming
Universal Remote Using Infra-Red Access
Programming Universal Remote Using Infra-Red Access Codes
Codes for VCRs
for Cable Television Converter Boxes
Determine brand of VCR.
Identify code(s) associated
with the brand in the infra-red code
index for VCRs (located in this manual).
Determine brand of Cable Television Converter box.
Identify code(s) associated
with the brand in the infra-red code
index for Cable Television Converter boxes (located in this manual).
Procedure
1. Place the Remote TV/VCR/CABLE
switch into the VCR position
(Center).
TVfVCPJCABLE
Procedure
1. Place the Remote TVNCR/CABLE
switch into the CABLE
position (Right)
TWVCPJCABLE
r-N
2. Press and hold VCR POWER button down on - Universal
Remote.
VCR
POWER
2. Press and hold the CABLE POWER button down on Universal
Remote.
CABLE
POWER
3. Enter two digit code using keyboard "0 through
9" buttons.
Release VCR Power button. The Universal
Remote is now
programmed.
3. Enter two digit code using keyboard "0 through 9" buttons.
Release VCR Power button. The Universal
Remote is now
programmed.
Use the Remote
VCR CHANNEL
UP/DOWN
buttons for selecting Cable Converter Box channels,
NOTE: Some brands have multiple codes. Repeat procedure
using each code listed until VCR responds correctly.
Alternate Procedure - Code Unknown
Programming Universal Remote Using the "Sequence Method"
for VCRs
Confirm VCR is plugged in and operating properly, then turn OFF.
Procedure
1. Place the Remote TV/VCR/CABLE
switch into the VCR position
(Center).
2. Press and hold the VCR POWER button down on Universal
Remote.
3. Press VOL RIGHT button repeatedly. Check for the VCR to turn
ON after each press. When the VCR turns ON, release VCR
Power button. The proper infra-red code has now been accessed.
NOTE: Some brands have multiple codes. Repeat procedure
using each code listed untilCable Television Converter
box responds correctly.
Alternate Procedure - Code Unknown
Programming Universal Remote Using the "Sequence
Method"
for Cable Television Converter Boxes
Confirm Cable Television Converter box is plugged in and operating
properly, then turn OFF.
Procedure
1. Place the Remote TVNCR/CABLE
switch into the CABLE
position (Right).
2. Press and hold the CABLE POWER button down on Universal
Remote.
3.
Press VOL RIGHT button repeatedly.
Check for the Cable
Television Converter box to turn ON after each press. When the
Cable Television Converter box turns ON, release Cable Power
button. The proper infra-red code has now been accessed.
NOTE: It may take several attempts before the correct code is
found.
The VOL LEFT button can be used to return to a code
that was accidently passed by.
Some Remote Controls may have unique operating
functions for some buttons. For Example: The POWER
button may only turn the VCR OFF as opposed to both
ON and OFF. It will then be necessary to modify the
procedure. Turn the VCR ON and repeatedly press the
VOL RIGHT button until the VCR turns OFF.
NOTE: It may take several attempts before the correct code is
found.
The VOL LEFT button can be used to return to a code
that was accidently passed by.
Some Remote Controls may have unique operating
functions for some buttons. For Example: The POWER
button may only turn the Cable Television Converter
box OFF as opposed to both ON and OFF. It will then
be necessary to modify the procedure. Turn the Cable
Television Converter box ON and repeatedly press the
VOL RIGHT button until the Cable Television Converter
box turns OFF.
!
NOTE: When operating equipment (VCR or Cable Converter box) with the Universal Remote Control, the TVNCR/CABLE
Switch J
should be set to the same position where the Access Code was first programmed for the equipment. Otherwise, leave the switch
!
in the "IV position.
-43-
Advertisement
Table of Contents
