Programming The Universal Remote Control - Panasonic CT-31SF12T Operating Instructions Manual

Programming The Universal Remote Control
VCR Cable Converter Box
Preferred Procedure- Code Known
Programming Universal Remote Using In-
fra-Red Access Codes for VCRs
• Determine brand of VCR.
• Identify code(s) associated with the brand in the
infra-red code index for VCRs (located in this
manual).
Procedure
1. Place the Remote TV/CABLE switch into the TV
position (Left). "rV/CABLE
2. Press and hold VCR POWER button down on
Universal Remote. VCR
POWER
3. Enter two digit code using keyboard "0 through 9"
buttons. The Universal Remote is now programmed.
NOTE: Some brands have multiple codes. Repeat
procedure using each code listed until VCR
responds correctly.
Alternate Procedure - Code Unknown
Programming Universal Remote Using the
"Sequence Method" for VCRs
• Confirm VCR is plugged in and operating properly,
then turn OFF.
Procedure
1. Place the Remote TV/CABLE switch into the TV
position (Left).
2. Press and hold the VCR POWER button down on
Universal Remote.
3. Press VOL RIGHT button repeatedly. Check for the
VCR to turn ON after each press. Stop pressing the
button when the VCR turns ON. The proper infra-red
code has now been accessed.
NOTE:
1. It may take several attempts before the correct code
is found.
2. The VOL LEFT button can be used to return to a
code that was accidently passed by.
3. Some Remote Controls may have unique operating
functions for some buttons. For Example: The
POWER button may only turn the VCR OFF as
opposed to both ON and OFF. It will then be
necessary to modify the procedure. Turn the VCR
ON and repeatedly press the VOL RIGHT button
until the VCR turns OFF.
Preferred Procedure- Code Known
Programming Universal Remote Using Infra-
Red Access Codes for Cable Television
Converter Boxes
• Determine brand of Cable Television Converter box.
• Identify code(s) associated with the brand in the
infra-red code index for Cable Television Converter
boxes (located in this manual).
Procedure
1. Place the Remote TV/CABLE switch into the CABLE
position (Right). TV/CABLE
2. Press and hold the CABLE POWER button down on
Universal Remote. CABLE
POWER
r--3
3. Enter two digit code using keyboard "0 through 9" but-
tons. Release CABLE power button. The Universal
Remote is now programmed. Use the Remote
CHANNEL UP/DOWN buttons for selecting Cable
Converter Box channels.
NOTE: Some brands have multiple codes. Repeat
procedure using each code listed until Cable
Television Converter box responds correctly.
Alternate Procedure- Code Unknown
Programming Universal Remote Using the
"Sequence Method" for Cable Television
Converter Boxes
• Confirm Cable Television Converter box is plugged in
and operating properly, then turn OFF.
Procedure
1. Place the Remote TV/CABLE switch into the CABLE
position (Right).
2. Press and hold the CABLE POWER button down on
Universal Remote.
3. Press VOL RIGHT button repeatedly. Check for the
Cable Television Converter box to turn ON after each
press. When the Cable Television Converter box turns
ON, release Cable Power button. The proper infra-red
code has now been accessed.
NOTE:
• It may take several attempts before the correct code is
found.
• The VOL LEFT button can be used to return to a code
that was accidently passed by.
• Some Remote Controls may have unique operating
functions for some buttons. For Example: The POWER
button may only turn the Cable Television Converter box
OFF as opposed to both ON and OFF. It will then be
necessary to modify the procedure. Turn the Cable
Television Converter box ON and repeatedly press the
VOL RIGHT button until the Cable Television Converter
box turns OFF.
NOTE: When operating equipment (TV, VCR or Cable Converter box) with the Universal Remote Control, the TV/CABLE
switch should be set to the same position where the Access Code was first programmed for the equipment.
Otherwise, leave the switch in the TV position.
- 30 -