Zephyr Tempest II AK7500ASX Use, Care And Installation Manual
Zephyr range hood use, care and installation guide
Hide thumbs
Also See for Tempest II AK7500ASX:
- Use, care and installation manual (22 pages) ,
- User, care, and installation manual (23 pages) ,
- Use, care and installation manual (22 pages)
Related Manuals for Zephyr Tempest II AK7500ASX
Summary of Contents for Zephyr Tempest II AK7500ASX
- Page 1 Tempest II AK7500ASX AK7536ASX AK7548ASX Model number: Serial Number: Date of Purchase: Sales Dealer: MAY12.0501 © 2012 Zephyr Corporation READ AND SAVE THESE INSTRUCTIONS...
- Page 2 www.zephyronline.com...
- Page 3 SAFETY NOTICE LIST OF MATERIALS INSTALLATION Ducting Calculation Sheet Mounting Height & Clearance Ducting Options Specifi cations Electrical Mounting the Range Hood CBIxxxB and PBI-1100A Internal Blowers CBI-xxxB Horizontal Ducting Conversion Remote Blower Preparation FEATURES & CONTROLS Touch Controls & Features MAINTENANCE Cleaning and Filter Removal Lights...
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
- Page 5 WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION To reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. OPERATION Always leave safety grilles and fi...
- Page 6 MODELS: AK7500ASX, AK7536ASX, AK7548ASX PARTS SUPPLIED 1 - Hood 2 - Baffl e fi lters AK7500ASX, 3 - AK7536ASX, 4 - AK7548ASX 2 - Halogen light bulbs 3 - AK7548ASX (pre-installed) 1 - 10” round transition adapter (for dual internal and external blowers)
- Page 7 Equivalent number Duct pieces length x used 3-1/ 4” x 10” 1 Ft. Rect., straight 6” Round, 1 Ft. straight 7”-10” Round, 1 Ft. straight 3-1/ 4” x 10” 15 Ft. Rect.90 elbow 3-1/ 4” x 10” 9 Ft. Rect.45 elbow 3-1/ 4”...
- Page 8 i n . ” m a x . ” m 3 6 ” DUCTING A minimum of 6” round or 3-1/4” x 10” rectangular duct must be used to maintain maximum air fl ow effi ciency for single internal blower and 10” round duct for dual internal and remote blower.
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certifi ed Silver Tape or Duct Tape. Some Ducting Options External Blower Roof Pitch w/...
- Page 10 ” 3/16 ” 1/16 elec blwr ” (30”) 15/16 ” (36”) 15/16 ” (48”) 15/16 ” 15/16 elec ” 7/16 24” (30”) 30” (36”) 42” (48”) back www.zephyronline.com ” 11/16 24” *10” transition used with dual and external blowers. 12” *10 ”...
- Page 11 ELECTRICAL WARNING All Electrical work must by performed by qualifi ed electrician or person with similar technical know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances.
- Page 12 4. Mark center line of wood board and align top of board with line B. Secure wood board to studs using (4) M4 wood screws. Wood Board Dimensions: (W x D x H) AK7500ASX - 28” x 3/4” x 4” AK7536ASX - 34” x 3/4” x 4” AK7548ASX - 46” x 3/4” x 4”...
- Page 13 PBI-1100A INTERNAL BLOWER COMPATIBLE WITH 10” ROUND VERTICAL DUCTING ONLY Please turn to page 12 for instructions on installing CBI-xxxB in horizontal ducting mode. 1. Position blower plate over bracket on inside back of hood and pivot up. Secure plate to hood with (2) 10x3/16”...
- Page 14 HORIZONTAL DUCTING IS ONLY AVAILABLE IF USING THE CBI-290B / CBI-600B SINGLE INTERNAL BLOWER. 1. Unscrew (4) screws holding blower to plate and remove blower. 3. Follow instructions on previous page and install blower plate into hood. 4. On the back of the hood, remove the (6) screws holding the rectangular cap to the hood.
- Page 15 6. Attach 6” round to rectangular transition adapter to hood with (4) M4x8 screws. 8. Place blower into round end of 6” round transition adapter. Attach brackets on blower to blower plate with (4) 3.5x8 screws. (2) screws for each bracket. 7.
- Page 16 1. Place 10” round adapter on top of hood and secure with (4) M4x8 screws. Connect 10” round duct work to 10” round adapter. 3. Place cap over threaded end of remote blower wiring and secure by turning clockwise. CBE-1000 / PBN-1000A: WIRING DIAGRAM Remote Blower Wiring Box (hood)
- Page 17 Lights On/Dim/Off 5 Min Delay Off Blower On/Off By pressing , the blower is switched On and Off. When switched on, the blower turns on at the same speed it was switched off at. When switched off the entire hood powers off, including the lights. Speed Selection The 3 speed levels are selected by pressing display indicates speed level selected.
- Page 18 Baffle Filter Clean Reminder Whether your hood is installed as an exhaust or purifying unit, a set if baffle filters are fitted by the factory, These baffle filters are intended to filter out residue from cooking. They need not be replaced on a regular basis but are required to be kept clean.
- Page 19 1. Push fi lter toward back of range hood using handles. 2. Pivot front of fi lter downward. 3. Remove fi lter by pulling away from hood. Replacing Baffle Filters Hood Model: Part No. Qty. to Order. AK7500ASX 50210004 AK7536ASX 50210004 AK7548ASX 50210004...
- Page 20 If bulbs are diffi cult to turn due to prolonged use, fi rmly attach a glass suction cup approximately the diameter of the bulb or use a rubber/latex glove and turn counter clockwise. Replacement bulbs are available at specialty lighting stores. Purchase type MR16 (GU-10) 35W halogen. For Zephyr part numbers please turn to page 20 of the manual.
- Page 21 TROUBLESHOOTING PROCEDURES FOR TEMPEST II Issue Cause After installation, 1. The power source is not turned ON. the unit doesn’t work. 2. The power line and the cable locking connector is not connecting properly. 3. The switch board and control board wirings are disconnected.
- Page 22 DESCRIPTION Replacement Parts Light Bulb MR16 (GU10) 35W (each) Baffl e Filter (each) Optional Accessories Single Internal Blower Dual Internal Blower External Blower In-Line Blower Heat Lamp Kit (30”) Heat Lamp Kit (36”) Heat Lamp Kit (48”) Back Splash (30”) Back Splash (36”) Back Splash (48”) 12”...
- Page 23 Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or work- manship as follows: Ten Year Limited Warranty for Parts: For ten years from the date of your original purchase of the Products, we will provide, free of charge, Products or parts to replace those that failed due to manufacturing defects.