For Power Tools - Craftsman 113.221611 Owner's Manual

FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW
If within one year from the date of purchase, this Craftsman Table Saw fails due to a defect in
material or workmanship, Sears will repair it, free of charge
WARRANTY SERVICE IS AVAILABLE BY RETURNING THE TABLE SAW TO THE NEAREST
SEARS RETAIL/CATALOG STORE OR SERVICE CENTER/DEPARTMENT IN THE UNITED
STATES
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state,
SEARS, ROEBUCK AND CO,,, Scars Tower, BSC 4%3, Chicago, iL 60684
GENERAL SAFETY iNSTRUCTiONS
FOR POWER TOOLS
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and
labels affixed to the tool Learn its application
and limitations as well as the specific potential
hazards peculiar to this tool
2. GROUND ALL TOOLS
This tool is equipped with an approved 3-
conductor cord and a 3-prong grounding type
plug to fit the propergrounding type receptacle,
The green conductor in the cord is the
grounding wire° Never connect the green wire to
a live terminal
3. KEEP GUARDS IN PLACE
In working order, and in proper adjustment and
alignment.
4. REMOVE ADJUSTING KEYS
AND WRENCHES
Form habit of checking to see that keys and
adjusting wrenches are removed from tool
before turning it on.
5. KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents.,
Floor must not be siippery due to wax or
sawdust.
6, AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet locations
or expose them to rain. Keep work area well
lighted Provide adequate surrounding work
space..
7, KEEP CHILDREN AWAY
All visitors should be kept a safe distance from
work area,
8. MAKE WORKSHOP CHILD-PROOF
-- with padlocks, master switches, or by
removing starter keys.
9. DON'T FORCE TOOL
It wit! do the job better and safer at the rate for
which it was designed
10. USE RIGHT TOOL
Don't force tool or attachment to do a job it was
not designed for.
11. WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties or
jewelry (rings, wrist watches) to get caught in
moving parts, Nonslip footwear is
recommended Wear protective hair covering to
contain tong hair Roll long sleeves above the
elbow
12. USE SAFETY GOGGLES (Head Protection)
Wear Safety goggles (must comply with ANSI
Z87.,1) at all times° Everyday eyeglasses only
have impact resistant lenses, they are NOT
safety glasses. Also, use face or dust mask if
cutting operation is dusty, and ear protectors
(plugs or muffs) during extended periods of
operation.
13. SECURE WORK
Use clamps or a vise to hold work when
practical It's safer than using your hand, frees
both hands to operate tool
14. DON'T OVERREACH
Keep proper footing and balance at all times,
15. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance,, Follow instructions for lubricating
and changing accessories,
16. DISCONNECT TOOLS
Before servicing; when changing accessories
such as blades, bits, cutters, etc
17_ AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF" position before
plugging in,
18. USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended
accessories, Follow the instructions that
accompany the accessories_ The use of
improper accessories may cause hazards.
19. NEVER STAND ON TOOL
Serious injury could occur if the tool istipped or
if the cutting tool is accidentally contacted,
Do not store materials above or near the toot
such that it is necessary to stand on the tool to
reach them
20. CHECK DAMAGED PARTS
Before further use of the tool, a guard or other
part that is damaged should be carefully
checked to ensure that it will operate properly
and perform its intended function., Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A
guard or other part that is damaged should be
properly repaired or replaced
21. DIRECTION OF FEED
Feed work into a blade or cutter against the
direction of rotation of the blade or cutter only
22. NEVER LEAVE TOOL RUNNING
UNATTENDED
Turn power off Don't leave tool until it comes to
a complete stop,