Table of Contents
Advertisement
2. ELEVATION
HANDWHEEL
,elevates orlowers
the blade, Turn counterclockwise
to elevate
clockwise
to lower
3. TILT HANDWHEEL
tilts the blade for bevel
cutting
Turn counterclockwise
to tift toward left
,
clockwise
to tilt toward right
When the blade is tilted to the LEFT as far as it witt
go, it should
be at 45 ° to the table and the bevel
pointer
should
point 45 °
NOTE: There are LIMIT STOPS inside the saw
which prevent the blade from tilting beyond 45 °
to
the
LEFT
and
90 ° to
the
RIGHT
(See
"Adjustments"
section "Blade Tilt, or Squareness
of Blade to Table")
4. MITER GAUGE
head is locked in position for
crosscutting
or mitering
by tightening
the lock
knob
ALWAYS LOCK IT SECURELY
WHEN IN
USE
5. BLADEGUARD
must always
be in place and
working
properly for all thru-sawing
cuts That is,
all
cuts
whereby
the
blade
cuts
completely
through
the workpiece
To
remove
the
guard
for
special
operation,
loosen both wing nuts, slide spreader
back and
up. DO NOT DISTURB
THE SETTING
OF THE
SPREADER
SUPPORT
BRACKET
When
replacing
the
guard,
insert
spreader
between
bracket
and clamp and slide forward
TIGHTEN
BOTH WINGNUTS
SECURELY
6. TABLE
INSERT
is removable
for removing
or"
installing
blades or other cutting
tools
WARNING:
FOR YOUR OWN SAFETY, TURN
SWITCH
"OFF"
AND
REMOVE
PLUG FROM
POWER
SOURCE
OUTLET
BEFORE
REMOVING
INSERT.
A Lower the blade below the table surface
B Raise blade guard
C Loosen Screw
(Do Not Remove)
,
D, Lift insert from front end, and pull toward front
of saw
NEVER
OPERATE
THE SAW WITHOUT
THE
PROPER
INSERT
IN PLACE.
USE THE SAW
BLADE
INSERT WHEN SAWING
. . USE THE
MOLDING
INSERT WHEN MOLDING
RIP FENCE,
is locked in place by tightening
the
lock knob
To move the fence, loosen the knob
and grasp the fence with one hand at the front
Holes are provided in the rip fence for attaching
a
wood
facing
when
using
the
dado head,
or
molding
head
Select a piece of smooth straight
wood approx
3/4" thick, at least as long as the rip fence, and at
Ieast 7-1/2"
wide (high)
to permit clamping
of
featherboards
Attach it to the fence with two Round Head #10
Wood Screws 2 in long
To remove the facing,
loosen the screws, slide the facing forward
and
puli the screws through
the round holes
WOOD
FACING
\
\
\
# 10 WOOD SCREWS
CAUTION:
When positioning fence for maximum
rip, make sure end of fence HEAD is even with edge
of table extension. Fence cannot be locked securely
beyond the edge of the table extension.
REMOVING
AND
INSTALLING
SAWBLADE
WARNING:
TO
AVOID
INJURY
FROM
ACCIDENTAL
START,
TURN
SWITCH
"OFF"
AND
REMOVE
PLUG
FROM
POWER
SOURCE
OUTLET
BEFORE
REMOVING
OR
INSTALLING
SAWBLADE.
NOTE: When installing
the blade
make sure the
upper saw teeth are pointing
toward the front of the
saw,
and that the blade and collars are clean, and
free from any burrs
The HOLLOW side of the collars must be against the
blade.
NOTE: Always place the LARGE collar on the shaft
before the blade
NOTE: Do not overtighten
arbor nut Use the arbor
wrench to just "snug" it
1 Loosen Phillips head screw in blade insert
Do
not remove
2 Remove blade insert by lifting stightly and pulling
insert to disengage
from key hole slot
PHILLIPS
BLADE
INSERT
HEAD
SCREW
I
21
Hide quick links:
Advertisement
Table of Contents
