Cleaning Procedures - Jenn-Air Pro-Style JGR8890ADP Use & Care Manual

4. Press the Autoset pad.
• "LITE" (Light soil level) is displayed.
5. Press the Autoset pad to scroll through the
self-cleaning settings.
"HVy" (Heavy Soil, 4 hours)
"MEd" (Medium Soil, 3 hours)
"LITE" (Light Soil, 2 hours)
Choosing the soil level of the oven automatically programs
the self-cleaning time.
6. After four seconds, CLEAN, DELAY and UPPER or LOWER
will light and LOCK will flash in the display. When the
oven door latches, LOCK will stop flashing and light
continuously to show that the oven is set for a delayed
clean operation. The delay time will display.
During the Self-Clean Cycle
When LOCK shows in the display, both oven doors lock. To
prevent damage to the doors, do not force the doors open
when LOCK is displayed.
Smoke and Smells
You may see some smoke and smell an odor the first few
times the oven is cleaned. This is normal and will lessen in
time.
Smoke may also occur if the oven is heavily soiled or if a
broiler pan was left in the oven.
Sounds
As the oven heats, you may hear sounds of metal parts
expanding and contracting. This is normal and will not
damage the oven.
After Self-Cleaning
About one hour after the end of the self-clean cycle, LOCK
will turn off. The doors can then be opened.
Some soil may leave a light gray, powdery ash. Remove
it with a damp cloth. If soil remains after wiping, that means
the clean cycle was not long enough. The soil will be
removed during the next clean cycle.
If oven racks were left in the oven and do not slide
smoothly after a clean cycle, wipe racks and rack supports
with a small amount of vegetable oil to make them easier to
move.
Fine lines may appear in the porcelain because it went
through heating and cooling. This is normal and will not
affect performance.
A white discoloration may appear after cleaning if acidic
or sugary foods were not wiped up before the self-clean
cycle. This discoloration is normal and will not affect
performance.
Notes:
• If an oven door is left open, "door" will appear in the
display and a signal will beep until the door is closed
and the Clean pad is pressed again.
• If more than 30 seconds elapse between pressing the
Clean pad and the Autoset pad, the program will
automatically return to the previous display.
• The oven doors will be damaged if the oven doors are
forced to open when LOCK is still displayed.

Cleaning Procedures

• Be sure appliance is off and all parts are cool before
handling or cleaning. This is to avoid damage and
possible burns.
• To prevent staining or discoloration, clean appliance after
each use.
• If a part is removed, be sure it is correctly replaced.
Broiler Pan and Insert
Never cover insert with aluminum foil as this prevents
the fat from draining to the pan below.
• Place soapy cloth over insert and pan; let soak to loosen soil.
• Wash in warm, soapy water. Use scouring pad to remove
stubborn soil.
• Broiler pan and insert can be cleaned in dishwasher.
Burner Grates - Porcelain on Cast Iron
• Allow burner grates to cool before cleaning.
• Wash with warm, soapy water and a nonabrasive, plastic,
scrubbing pad. For stubborn soils, clean with a soap-filled,
nonabrasive, plastic pad or Cooktop Cleaning Creme* (Part
#20000001)** and a sponge. If soil remains, reapply
Cooktop Cleaning Creme, cover with a damp paper towel
and soak for 30 minutes. Scrub again, rinse and dry.
• Do not clean in the dishwasher or self-cleaning oven.
Burner Caps and Sealed Gas Burner Bases
Removable Burner Heads
• Allow burner to cool. Remove burner cap and wash in soapy
water with a plastic scouring pad. For stubborn soils, clean
with a soap-filled, nonabrasive pad or Cooktop Cleaning
Creme* (Part #20000001)** and a sponge.
• Do not clean in the dishwasher or self-cleaning oven.
Sealed Gas Burner Bases
• Clean frequently. Allow burner to cool. Clean with soap and
plastic scouring pad. For stubborn soils, clean with a soap-
filled, nonabrasive pad. Do not enlarge or distort holes.
• Be careful not to get water into burner ports.
• Use care when cleaning the ignitor. If the ignitor is wet or
damaged the surface burner will not light.
* Brand names are registered trademarks of the
respective manufacturers.
** To order call 1-800-JENNAIR (1-800-536-6247).
6
CAUTION
Cont.