Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Graco Hydra-Clean 3035
Summary of Contents for Graco Hydra-Clean 3035
- Page 1 READ AND RETAIN FOR REFERENCE 800-065 SERIES 3000 (207 bar) OPERATING PRESSURE 3400 1234 MAXIMUM WORKING PRESSURE bar) . : I . ~. j. : : NEEQBPOUS. @. B.0.50x .l44)1 ! 5 5 " 1 4 & 3 OCOPYRIGHT 1984 GRACO INC.
- Page 2 INJECTION HAZARD FBWE Fluids under high pressure from spray or leaks can Do not spray flammable liquids. Do not operate the penetrate the skin and cause extremely serious .engine where combustible fumes or dust may be injury, including the need for amputation. present.
- Page 3 Refer to the engine instruction booklet provided with Connect Water Supply the unit. Install Hose and Spray Gun Connect the spray hose to-the spray gun by inserting the pin at the end of the hose into the quick disconnect coupler on the gun. Connect the hose to Do not exceed 160°F (7OoC) water.temperature to pump in a direct supply system.
-
Page 4: Operation
OPERATION Startup When shutting .down for the day or weekend, shut off Before starting, be sure to read the safety warnings and unit, shut off water supply valve, and trigger gun setup instructions. release pressure. Wipe off the unit with a damp rag. Check the oil'and gasoline levels daily. -
Page 5: Troubleshooting
SERVICE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Engine Will Not Start No gasoline in fuel tank or Fill the tank with gasoline, open fuel shut-of Or Hard To Start. carburetor, valve. Check fuel line and carburetor. Water in gasoline or old fuel. Drain fuel tank and carburetor. -
Page 6: Parts Drawing
PARTS DRAWING Pressure Washer Assembly, 800-065 2 0 - y 801-643... - Page 7 "- LIST PARTS Pressure Washer Assembly. 800-065 REF. PART REF. PART a n . QTY. NO. NO. DESCRIPTION DESCRIPTION 800-130 GUN ASSEMBLY. see parts 601-3154 BELTGUARD COVER drawing/list page 10 801-500 BELTGUARD BASE TIP. 0004 MEG, 1/4 thd., Oo "801 -599 801 -539 BUMPER -600...
- Page 8 Pump (Refer to Parts Drawing, 'Page NOTE: Two sizes of metric wrenchesare necessary 8. Lubricate each plunger and carefully slide manifold for servicing the pump; M13 and M30. onto crankcase. Valves: 9. Replace the eight capscrews and snug them up. 1.
-
Page 9: Part§ Drawing
PART§ DRAWING UNLOADER ASSEMBLY PACKING & RETAINER KIT 801 -487. (Three kits needed entire pump.) PLUNGER REPAIR Includes: KIT 801 -474 REF. QTY. Includes: UNIT OIL SEAL KIT VALVE PACKING REF. QTY. 801 -472 801 -473 801 -486 Includes: Includes: Includes: REF. - Page 10 Couplers NOTE: Hose. Quick Spray Tips not included with Gun Assembly Pressure Washer Assembly Parts Drawing/List. page Gun Assembly, 800-130 REF. PART DESCRIPTION 801-134 TUBE. 32" 801-674 GRIP COUPLER, quick disconnect -009 female SERVICE 801-638 'SPRAY GUN, (replaceable Gun, Cartridge Replacement pans include items 5-18) 801-639 CARTRIDGE...
- Page 11 ACCESSORBES (Must purchased separately) @J&vg&g#.>;:. CHEIWICAL'IMJECTQW 800-987 WATER SANDBLASTER 800-120 abrasive cleaning of stubborn dirt and paint. For injecting harsh cleaning chemicals downstream Spray tip not included in kit. from pump. FLOW PREVENTOR BACK 801-133 SPRAY 801-600 Prevent back-up of contaminated water into fresh supply.
- Page 12 This warranty does not cover damage which. in the reasonable judgment of Graco. a w e s from misuse. or wear abrasion, corrosion. negligence, accident. substitution of nun-Graco parts. faulty installation tampering.