2500 psi 172 bar operating pressure, 2900 psi 200 bar maximum working pressure, 3000 psi 207 bar operating pressure, 3400 psi 234 bar maximum working pressure (20 pages)
Page 1
INSTRUCTIONS-PARTS LIST manual This wntains IMPORTANT WARNINGS and INSTRUCTIONS READ AND RETAIN HYDRA-CLEAN Pressure Washers HYDRA-CLEAN" 2510 P/N 800-901, Series A 2500psi (172 bar) OPERATING PRESSURE 2900 psi (200 bar) MAXIMUM WORKING PRESSURE HYDRA-CLEAN" 3009 P/N 800-900, Series A 3000 psi (207 bar) OPERATING PRESSURE 3400 psi (234 bar) MAXIMUM WORKING PRESSURE supply...
Page 2
Read and understand all instruction manuals before operating equipment. FLUlD 1NJECTlON HAZARD General Safety This pressure washer generates very pressure. Spray from the gun, leaks or tuptured components can inject fluid through your skin and into your body and cause extremely serious bodily injury including the need for amputation.
(GFCI). EQUIPMENT MISUSE HAZARD General Safety Any misuse of the pressure washer or accessories, such as overpressurizing, modifying parts, using incompatible chemicals and fluids, or using worn or damaged parts, can cause them...
Page 4
KEEP CLEAR body parts. of moving parts when starting or operating the pressure washer. high pressure fluid from the gun. N N E R operate the pressure washer without all guards and interlocks installed and functioning. Follow the TERMS WARNING or DANGER Alerts user to avoid or correct conditions that could cause bodily injury.
INSTALLATION LEVEL Figure 1 Check Shipping Damage Check the unit for any damage that may have occurred in shipping. Notify the carrier Immediately any damage. Set Up Before connecting the unit, be sure the electrical setvice matches the specification in Technical Data (inside back cover) and the voltage label on the unit.
Page 6
6. ALWAYS observe the following CAUTIONS to avoid costly damage to the pressure washer. DO NOT allow the pressure washer to idle for more than 10 minutes. Doing recirculating water to overheat and seriously damage the pump.
5. l i p holding holes are provided on the chassis, To avoid blowing the O-ring coupler, due to the high pressure In the system, never operate the pressure washer without securely mounted in the quick coupler. Flgure 3 Tips...
Pressure Relief Procedure Warning before proceeding. 308-535 If the pressure washer will be exposed to freezing temperatures, drain all water out of the pump. If it must be stored in freezing temperatures, flush the unit with a pressure.
PUMP SERVICE WARNING To reduce the risk of serious bodily injury, including fluid injection, splashing in the eyes or on the skin, or injury from moving parts, always follow the Pressure Relief Procedure Warnlng before proceeding. NOTE: The following metric wrenches are needed: M10, Mi3 and M30.
Servicing the V-Packings NOTE: There are two types of packing kits: one is packings only, the other packings, rings and retainers. 1. Remove the manifold as outlined in the Pumping Section. Carefully pull the packing retainer from the manifold. Examine the O-ring and replace it if it is cut or damaged.
Water Pumo Maximum Flow Dimensions Length Width Height Maximum Inlet Water Temperature wetted parts High Pressure H o s e Bypass Pressure Washer (including fittings) 308-535 Model 800-901 phase 20 HP, amp/3 phase or 2% voIff50 amp13 phase voIff.25 bar)
THE GRACO WARRANTY WARRANTY AND DISCLAIMERS Graoawarmntsallequipmentmanufactursdby~andbearingitsnametobefreefmmdefectslnmaterial and workmanship the date of sale by an authorized Graw distributor Aspurohaser'ssolemmedyforbreachofthiswarranty,Gramwill,foraperiodoltwentyfourmonthsfmm dateofsale,repairorrepiaceanypartdtheequipmentprovende~~.Thiswarr~appliesonlywhen the equipment Is installed. operated and maintained in recommendations. T h i s warranty does not cover, and Gram shall n d be liable for, any malfunction. damage or wear by fauity installation.