Page 1
Model SP2600VSP Super Pump Variable Speed Pump The Hayward Super Pump VS is specifically engineered for the demanding requirements of today’s in- ground swimming pool/spa that is equipped with large capacity filters, heaters, and pool cleaning equipment. The totally enclosed, permanent magnet motor combined with its advanced hydraulic design provides unparalleled energy savings.
9.4. Seal Installation 9.5. Replacing the Impeller and Diffuser 9.6. Replacing the Motor Assembly Replacement Parts ............................. 19 10.1. Parts Diagram Troubleshooting ............................20 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 2 of 24 Super Pump Variable Speed Pump IS2600VSP Rev C...
Page 3
11.1. General Problems 11.2. Error Codes Warranty ..............................22 Product Registration ........................... 23 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 3 of 24 Super Pump Variable Speed Pump IS2600VSP Rev C...
– All electrical wiring MUST be in conformance with all applicable local codes, regulations, and the National Electric Code (NEC). USE OF NON-HAYWARD REPLACEMENT PARTS VOIDS WARRANTY. ATTENTION INSTALLER - THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE INSTALLATION, OPERATION, AND SAFE USE OF THIS VARIABLE SPEED PUMP THAT MUST BE FURNISHED TO THE END USER OF THIS PRODUCT.
Page 5
Mechanical Entrapment - There is potential for jewelry, swimsuits, hair decorations, fingers, toes, or knuckles to be caught in an opening of a suction outlet cover resulting in mechanical entrapment. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 5 of 24...
WARNING – Failure to install according to defined instructions may result in severe personal injury or death. SAVE THESE INSTRUCTIONS USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 6 of 24 Super Pump Variable Speed Pump IS2600VSP Rev C...
2. General Information 2.1. Introduction This manual contains information for the proper installation and operation of the Hayward Super Pump Variable Speed Pump. The instructions in this manual MUST be followed precisely. 2.2. Primary Features Totally enclosed, permanent magnet motor ...
Allow for valves in suction and discharge piping. Be protected from excess moisture and flooding. Allow adequate access for servicing pump and piping. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 8 of 24 Super Pump Variable Speed Pump...
3. Connect 230VAC line power supply wiring to the terminal block and ground screw as shown in the Input Power Wiring diagram. See section 5.1 for diagram. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 10 of 24 Super Pump Variable Speed Pump...
Have a professional perform this test. 2. Ensure all Hayward pump and system components are removed from system prior to performing test. WARNING – If circulation equipment must remain in the plumbing system during water pressure test, do not apply more than 10 psi pressure to the system.
Be sure all suction and discharge valves are open when pump is running. See Troubleshooting Guide. 6.3. User Interface Summary Figure 6.3-1 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 12 of 24 Super Pump Variable Speed Pump IS2600VSP Rev C...
Pump software revision number will be . displayed across the screen. Displays the Motor RPM DISP/FUNC Cycles through to next screen USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 13 of 24 Super Pump Variable Speed Pump IS2600VSP Rev C...
Note: The prime mode timer can be adjusted up to 4 minutes and down to 0.00 minutes. When adjusted to 0.00 minutes, prime mode will be disabled. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 14 of 24 Super Pump Variable Speed Pump...
The LED for the changed speed will FLASH as long as a modified speed is running and has not been saved. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 15 of 24...
In this mode only the motor RPM’s can be changed. To exit from service mode, cycle the power to the pump off and on. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 16 of 24 Super Pump Variable Speed Pump...
Keep motor clean. Insure motor air vents are free from obstruction to avoid damage. Do NOT use water to hose off motor. Occasionally, shaft seals must be replaced, due to wear or damage. Replace with genuine Hayward seal assembly kit. See “Shaft Seal Change Instructions” in this manual.
Disconnect all electrical power service to pump before beginning shaft seal replacement. Only qualified personnel should attempt rotary seal replacement. Contact your local authorized Hayward Dealer or service center if you have any questions. Exercise extreme care in handling both the rotating and the stationary sections of the two-part replacement seal. Foreign matter or improper handling will easily scratch the graphite and ceramic sealing surfaces.
SPX1600AA Pump/Strainer Housing With Gasket SPX1600R Diffuser Gasket SPX1616B Diffuser SPX1621C Impeller SPX1600Z2 Shaft Seal Assembly SPX1600T Housing Gasket SPX1611E5 Seal Plate USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 19 of 24 Super Pump Variable Speed Pump IS2600VSP Rev C...
4. Strainer basket or skimmer basket loaded with debris. Remove the strainer housing cover or the skimmer cover. Clean the basket, and refill the strainer housing with water. Tighten the cover. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 20 of 24...
Page 21
All seal leaks should be replaced at once. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 21 of 24 Super Pump Variable Speed Pump...
Page 22
Overload During Start Up Process Short Circuit Failure Multiple Errors at the Same Time, i.e. Undervoltage and Overload Error Communication Failure From controller 12. Warranty USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 22 of 24 Super Pump Variable Speed Pump IS2600VSP Rev C...
INITIAL PRESSURE GAUGE READING AT 3,000 RPM (CLEAN FILTER) _______________________ PUMP MODEL __________________ *Retain this Warranty Certificate in a safe and convenient location for your records USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 23 of 24 Super Pump Variable Speed Pump IS2600VSP Rev C...
Mail to: Hayward Pool Products, 620 Division Street, Elizabeth, NJ 07207 Installation for: Attn: Warranty Dept In Ground Or REGISTER YOUR WARRANTY ON-LINE AT WWW.HAYWARDPOOL.COM is a registered trademark and Super Pump VS is a trademark of Hayward Industries, Inc. 2013 Hayward Industries. All rights reserved.
Need help?
Do you have a question about the Super Pump® VS and is the answer not in the manual?
Questions and answers