Advertisement
cAuTioN
/
SPIDER
ALERT!
SPIDERAND WEBS
INSIDE BURNER TUBE
ff you notice that your grill is getting hard to light or that the
flame isn't as strong as it should be, take the time to check and
clean the burner tubes.
in someareasof the country,spidersor small insectshavebeen
knownto create"flashback"problems. T he spidersspinwebs,build
nestsand layeggs in the grill'sburnertube(s)obstructingtheflow of
gasto the burner.Thebacked-upgascan ignitein the burnertube
behindthecontrol panel,This is knownas a flashbackand it can
damageyourgrill and evencauseinjury,
Topreventflashbacksand ensuregoodperformancetheburner
tubeassemblyshouldbe removedfrom thegrill and cleaned
beforeusewheneverthegrill hasbeen idlefor an extendedperiod,
•Stainless steel surfaces: To maintain your grill's high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
Storing Your Grill
•Clean cooking grates.
•Store in dry location.
•When LP cylinder is connected to grill, store outdoors in a well-
ventilated space and out of reach of children.
•Cover grill if stored outdoors. Choose from a variety of grill
covers offered by Sears or other qualified dealers.
•Store grill indoors ONLY if LP cylinder is turned off and
disconnected, removed from grill and stored outdoors.
•When removing grill from storage, follow "Cleaning the Burner
Assembly" instructions before starting grill.
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting grill.
1.
Turn gas off at control knobs and LP cylinder.
2.
Remove grease tray from back of grill.
3.
Open doors, remove tank heat shield and grease pan from
underneath the firebox.
4.
Remove screws that hold orifice holder with the burner
tube. Figure A
5.
Remove cooking grates and radiator plates.
6.
Remove hitch pin from front of the burner to disengage it.
Figure B
7.
Carefully lift up the burner enough to expose the electrode
wire. Detach wire from electrode underneath the burner
8.
Carefully take out the burner to clean. Figure C
9.
While cleaning, make sure that the ignitor wire is not bent
or broken.
General Grill Cleaning
•Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Plastic parts: Wash with warm soapy water and wipe dry.
A Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
•Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
•Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
Front
Orifice Holder
464222209,9
Advertisement
