Summary of Contents for Emerson HIGH COUNTRY KF160OI01
Page 1
BP7283, High Country, KF160 7/31/06 10:54 AM Page 1 READ AND SAVE THESE INSTRUCTIONS Emerson Fans Designed by HIGH COUNTRY Ceiling Fan Owner's Manual Model Number KF160OI01 Olde Iron with Washed Oak/Honey Maple Blades Net Weight: 30.6 Lbs. Part No. F40BP72830004 Form No.
DATE CODE: The date code of this fan may be found on the box, stamped in ink on a white label. You should record this data above and keep it in a safe place for future use.
Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or property damage. 10:54 AM Page 3 1.
BP7283, High Country, KF160 7/31/06 General Your Emerson ceiling fan comes equipped with a remote control transmitter and a remote control receiver. This remote con- trol systems is designed to control your ceiling fan speed, airflow direction, and light intensity.
Any electrical work not described in these instructions should be done or approved by a licensed electrician. If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the exist- ing light fixture.
Page 6
WARNING To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balanc- ing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades. FIBER WASHER (3)
Page 7
10. Tighten the setscrews (Figure 6) secure- ly while pulling up on the downrod. NOTE: The setscrews must be properly installed as described above, or fan wobble could result. NOTE: If you installed the 3-1/2” down- rod, the decorative scroll assembly and decorative cover will not be installed.
You can now proceed with hanging and wiring your fan. How to Hang Your Ceiling Fan WARNING The fan must be hung with at least 7' of clearance from floor to blades (Figure 9). CEILING AT LEAST Figure 9...
1. Position the supply wires to the left side of the outlet box (Figure 12); position the fan wires to the right side. Partially insert the remote control receiver (flat side up) until one end rests on the hanger ball as shown in Figure 12.
Page 10
7 and 8. Otherwise, skip to step 9. 7. For Operating Your Fan With the Downlight Fixture. Remove the thread- ed plug from the light fitter adapter. Feed the black and white wires of the...
Page 11
60-WATTCANDELABRA BLACK BASE BULB (3) WIRE SOCKET RUBBER WASHER LOWER GLASS Figure 18 FINIAL NUT 11. Your ceiling fan is now installed and wired to be controlled by your remote control system. LIGHT FITTER THREADED NIPPLE DECORATIVE...
1. Restore electrical power to the outlet box by turning the electricity on at the service panel. 2. To set the desired fan speed, press the HIGH, MED, or LOW buttons to oper- ate your fan on high, medium, or low speed.
This product is designed to use only those parts supplied with this prod- uct and/or any accessories designat- ed specifically for use with this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co.
BP7283, High Country, KF160 7/31/06 WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE PROBABLE CAUSE 1. Fan will not 1. Fuse or circuit breaker start. blown.
FOLLOWING INFORMATION: • PART NUMBER • PART DESCRIPTION • NAME OF ITEM • MODEL NUMBER The model number of your Fan will be found on a label attached to the top housing. For repair parts, phone 1-800-654-3545. 10:54 AM Page 15 Part Number Model No.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible for any such damage.