Related Manuals for Lightolier IS_LSC
Summary of Contents for Lightolier IS_LSC
- Page 1 IS_LSC Lighting Systems 9” 2-3/8” We reserve the right to change details of design, materials and finish.
- Page 2 IS_LSC Lighting Systems TABLE OF CONTENTS ..........................3 ...............................................................7 .........................................." TEE ....................10 ......................11 We reserve the right to change details of design, materials and finish.
- Page 3 IS_LSC Lighting Systems SAMPLE PART LIST Strain Relief Canopy 4-1/2” Ø 1/4 -20 Coupling 1/16" Ø SJT Power Cord SS CABLE End-Cap Reflector Grip-Lock and Leveling Bar Housing Draw-Tight Joiner Assembly We reserve the right to change details of design, materials and finish.
-
Page 4: Lighting Systems
IS_LSC Lighting Systems SAMPLE RUNS 48" End Cap Fixture 4' Module 4’ 10” 96" End Cap Fixture 8' Module 8' 10" 144" End Cap Fixture 12' Module 12' 10" 96" 96" End Cap Fixture Fixture 16' Module 16' 10" 96" 144"... - Page 5 IS_LSC Lighting Systems PHASE 1 - MAKING THE STARTER FIXTURE End-Cap Grip-Lock Grip-Lock Weld-Stud Wire Nuts Wire Nuts (by others) (by others) Weld-Stud Leveling Bar Receiver Figure 1 We reserve the right to change details of design, materials and finish.
- Page 6 IS_LSC Lighting Systems PHASE 1 - MAKING THE STARTER FIXTURE (CONT’D) Do not over tighten. Note: Joiner fixtures only. For individual fixtures, proceed to Phase 3. Weld-Stud Weld-Stud Grip-Lock Connecting Wires Go Through Here Weld-Stud Weld-Stud Receiver Receiver Leveling Bar Figure 2 We reserve the right to change details of design, materials and finish.
- Page 7 IS_LSC Lighting Systems PHASE 2 - MAKING THE INTERMEDIATE FIXTURE Note: If fixture is an individual, skip Phase 2 and go to Phase 3. Draw-Tight Bolt Bolt Goes into the Draw-Tight Bracket Figure 3 We reserve the right to change details of design, materials and finish.
- Page 8 IS_LSC Lighting Systems PHASE 3 - MAKING END OF RUN FIXTURE Weld-Stud Flush with Inside of Receiver Figure 4 We reserve the right to change details of design, materials and finish.
- Page 9 IS_LSC Lighting Systems CANOPY DETAIL - SLOT TEE SUPPORT CABLE (BY OTHERS) CADDY CLIP SLOT TEE STANDARD SLOT TEE (BY OTHERS) 1/4-20 STUD STRAIN RELIEF CANOPY 4-1/2” Ø 1/4-20 COUPLING SJT POWER CORD We reserve the right to change details of design, materials and finish.
- Page 10 IS_LSC Lighting Systems CANOPY DETAIL - STANDARD 1" TEE SUPPORT CABLE (BY OTHERS) STANDARD 1” TEE CADDY CLIP STANDARD 1” TEE (BY OTHERS) STRAIN RELIEF 1/4-20 STUD CANOPY 4-1/2” Ø SJT POWER CORD 1/4-20 COUPLINGS We reserve the right to change details of design, materials and finish.
- Page 11 IS_LSC Lighting Systems CANOPY DETAIL - JUNCTION BOX JUNCTION BOX (BY OTHERS) 1/4-20 STUD STRAIN RELIEF #8-32 SCREWS (BY OTHERS) CANOPY 4-1/2” Ø SJT POWER CORD 1/4-20 COUPLING We reserve the right to change details of design, materials and finish.
Need help?
Do you have a question about the IS_LSC and is the answer not in the manual?
Questions and answers