Advertisement
Installation
<ENGLISH>
Parts supplied
®
Rear view camera X I
®
RCA power supply cable X
©
Power supply unit X I
@ Hexagon wrench X I
®
Hook and loop fastener (soft type) X I
®
Hook and loop fastener (hard type) X
®
Clamp X 6
®
Waterproof pad X I
CD
Double-sided tape X
Installation example (Fig. 1)
CD
Glass surface
@
Make sure it doesn't touch the wiper
@
Install on the center part
Installation Procedure
Note:
Before making a final installation of the unit,
temporarily connect the wiring to confirm that
the connections are correct and the system works
properly.
Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
Install the unit where it does not get in the driver"
s way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
When mounting this unit, make sure none of the
leads are trapped between this unit and the sur-
rounding metalwork or fillings.
To prevent electric shock, do not install the power
supply unit in places where it might come in con-
tact with liquids.
Do not mount this unit near the heater outlet,
where it would be affected by heat, or near the
doors, where rainwater might splash OnlO it. (Never
install in locations such as the above because of
the danger of malfunction due to high tempera-
tures.)
Before drilling any mounling holes always check
behind where you want to drill the holes. Do not
drill into the gas line, brake line, electrical wiring
or other important parts.
If this unit is installed in the passenger compartment,
anchor it securely so it does not break free while the
car is moving, and cause injury or an accident.
If this unit is installed under a front seat, make
sure il does nOI obslruct seat movement. Route
all leads and cords carefully around the sliding
mechanism so they do not get caught or pinched in
the mechanism and cause a short circuit.
o
Locate in the position you want to install thl' rear
view camera, Adjust the angle of the rear \ lew
camera, and install so that the camera doe,n't
touch the car.
o
When sticking to a glass surface, stick it on in a
position that assures the camera doesn't touch the
rear window.
o
Install so that it does not obstruct the rear field of
view.
o
Install so that it does not protrude from the side of
the car.
o
Do not perform installation in rain or fog.
o
When humidity is high, dry the surface to which
the unit is to be attached before installing, Moisture
on the attachment surface reduces adhesive strength
which may lead to the unit coming off.
o
If the temperature of the attachment surface is
low, warm with a hair dryer of other means before
installing to improve adhesive strength.
o
Do not attach the camera stand to areas on the car
body treated with fluorocarbon resin, or glass. This
may result in the rear view camera falling off.
o
During the 24-hour period after installing:
- Do not apply water to the unit.
- Do not expose the unit to rain.
- Do not subject the camera to unnecessary force,
Thoroughly clean where tape is used for sticking
on the unit.
1. Clean the surface to which the rear
view camera is to be installed.
(Fig. 2)
Use a cloth or other item to wipe oil, wax,
dust and any other dirt from the installation
surface.
2. Peel off the sheet on the back of the
camera stand and stick it on. (Fig. 3,
Fig. 4, Fig. 5)
Press the camera stand with your fingers
to
stick it to the installation surface, Touching
the adhesive surface or sticking the unit
on a second time reduces adhesive power
which may result in the unit coming off.
CD
Camera stand
®
Top
®
Mark
®
Bottom
®
Make sure to install the rear view camera so
that the mark is located on top of the camera.
®
Be sure not to hide any part of the characters
on the license plate when auaching the cam-
era.
3. Adjust the angle so that the bumper
or rear edge of the car is displayed
at the bottom of the TV screen.
(Fig. 6, Fig. 7, Fig. 8)
CD
Hexagon wrench
®
Bumper or rear edge of car
4. Attach the power supply unit.
(Fig. 9)
Affix the Hook and loop fastener (hard
type) to the bottom of the power supply
unit, and affix the Hook and loop fastener
(soft type) to the mounting location,
CD
Power supply unit
®
Hook and loop fastener (hard type)
@
Hook and loop fastener (soft type)
• You can use Hook and loop fastener (hard
type) to attach directly to a carpet, but do not
use the soft
type,
• Install the power supply unit close enough
for the rear view camera cable to reach,
Installation
<ENGLISH>
Parts supplied
@ Rear view camera X I
®
RCA power supply cable
X
©
Power supply unit X I
@
Hexagon wrench X I
®
Hook and loop fastener (soft type) X I
®
Hook and loop fastener (hard type) X
®
Clamp X 6
®
Waterproof pad X I
<D
Double-sided tape
X
Installation example (Fig. 1)
CD
Glass surface
®
Make sure it doesn't touch the wiper
@
Install on the center part
Installation Procedure
Note:
• Before making a final installation of the unit,
temporarily connect the wiring to confirm that
the connections are correct and the system works
properly.
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver"
s way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• When mounting this unit, make sure none of the
leads are trapped between this unit and the sur-
rounding metalwork or fiHings.
To prevent electric shock, do not install the power
supply unit in places where it might come in con-
tact with liquids.
• Do not mount this unit near the heater outlet,
where it would be affected by heat, or near the
doors, where rainwater might splash onto it. (Never
install in locations such as the above because of
the danger of malfunction due to high tempera-
tures.)
Before drilling any mounting holes always check
behind where you want to drill the holes. Do not
drill into the gas line, brake line, electrical wiring
or other important parts.
• If this unit is installed in the passenger compartment,
anchor it securely so it does not break free while the
car is moving, and cause injury or an accident.
If this unit is installed under a front seat, make
sure it does not obstruct seat movement. Route
all leads and cords carefully around the sliding
mechanism so they do not get caught or pinched in
the mechanism and cause a short circuit.
Locate in the position you want to install the rear
view camera. Adjust the angle of the rear \ lew
camera, and install so that the camera doe,n't
touch the car.
• When sticking to a glass surface. stick it on in a
position that assures the camera doesn't touch the
rear window.
• Install so that it does not obstruct the rear field of
view.
• Install so that it does not protrude from the side of
the car.
• Do not perform installation in rain or fog.
• When humidity is high. dry the surface to which
the unit is to be attached before installing. Moisture
on the attachment surface reduces adhesive strength
which may lead to the unit coming off.
• If the temperature of the aHachment surface is
low, warm with a hair dryer of other means before
installing to improve adhesive strength.
• Do not attach the camera stand to areas on the car
body treated with fluorocarbon resin, or glass. This
may result in the rear view camera tid ling off.
• During the 24-hour period after installing:
- Do not apply water to the unit.
- Do not expose the unit to rain.
- Do not subject the camera to unnecessary force.
• Thoroughly clean where tape is used for sticking
on the unit.
1. Clean the surface to which the rear
view camera is to be installed.
(Fig. 2)
Use a cloth or other item to wipe oil, wax,
dust and any other dirt from the installation
surface.
2. Peel off the sheet on the back of the
camera stand and stick it on. (Fig. 3,
Fig. 4, Fig. 5)
Press the camera stand with your fingers to
stick it to the installation surface. Touching
the adhesive surface or sticking the unit
on a second time reduces adhesive power
which may result in the unit coming off.
CD
Camera stand
®
Top
®
Mark
®
Bottom
®
Make sure to install the rear view camera so
that the mark is located on top of the camera.
®
Be sure not to hide any part of the characters
on the license plate when attaching the cam-
era.
3. Adjust the angle so that the bumper
or rear edge of the car is displayed
at the bottom of the TV screen.
(Fig. 6, Fig. 7, Fig. 8)
CD
Hexagon wrench
(3)
Bumper or rear edge of car
4. Attach the power supply unit.
(Fig. 9)
Affix the Hook and loop fastener (hard
type) to the bottom of the power supply
unit, and affix the Hook and loop fastener
(soft type) to the mounting location.
CD
Power supply unit
®
Hook and loop fastener (hard type)
@
Hook and loop fastener (soft type)
• You can use Hook and loop fastener (hard
type) to attach directly to a carpet, but do not
use the soft type.
• Install the power supply unit close enough
for the rear view camera cable to reach.
Advertisement
