Advertisement
Installation
Specified Installation Position
⨋
Install this product in a vehicle and at a position that satisfies all of the following conditions.
—
A position where the lens of this product is in the area swept by the windshield wipers.
A position where the lens of this product is not affected by the sun visor and frit band.
—
A position where this product faces in the horizontal direction to the front and side to side.
—
—
A position where the Cigarette Lighter Power Cable can easily reach the socket.
This product must be slid to the left to remove it from the bracket after installation to the front windshield. If this
⨋
product is installed too close to the rear view mirror when it is installed on the right side of the rear view mirror in
a left-hand drive vehicle, you will not be able to remove it from the bracket.
Installation Angle
Installation Direction
Allowable Installation Angle: 5° to 80°
(With Lens Horizontal)
This product
Forward Direction
Front Wind
Front Wind
This product
Drive Recorder Unit
of Vehicle
Front Windshield
shield
shield
This product
*Install this product in a location where it will
Horizontal Direction
Horizontal Direction
not interfere with the driver's field of view,
such as behind the rearview mirror.
Within 20 % of Height
Rearview Mirror
This product
Range of Windshield Wipers
A Pillar
IMPORTANT
Always install this product in the specified installation position to ensure a safe field of view while driving and to
achieve full performance from the product.
1 Clean the installation area of
3 Route the cable.
dirt and oils using the included
cleaning cloth.
Horizontal Direction
2 Install this product.
Ground
Peel off the sticker on the Installation Bracket
(①) and attach this product to the front
windshield.
Firmly push the top of the product and both
sides of the LCD (②). Never touch the surface
of the LCD.
Installation Bracket
1
A Pillar
2
4 Adjust the angle of the lens.
Use extreme care as the double-sided tape
on the Installation Bracket in (①) is extreme-
Airbag
ly strong, and it will be difficult to reapply the
tape once it has been applied.
Note
A protective film is applied to the lens when the prod-
uct is purchased. Peel off this film.
Removing this product
The Installation Bracket is attached to this product when the product is purchased. After this product is installed in
the vehicle, remove this product from the Installation Bracket with the following steps.
1 Slide this product to the left as viewed from the LCD of this product.
Route the Cigarette Lighter Power Cable to the
passenger seat side.
2 Remove this product so that the hooks on the Installation Bracket disengage
Cigarette
from the slots on this product.
Lighter
Power Cable
The power terminal will be extremely hot
Installation Bracket Slots
immediately after using the cigarette lighter.
The tip of the Cigarette Lighter Power Cable
may melt or short circuit if it is plugged in
while hot. Wait for the terminal to cool be-
fore plugging in the Cigarette Lighter Power
Cable.
Reverse the steps to reattach this product. Line up and fit together the hooks on the Installation Bracket with the
slots on this product, then slide this product to the right as viewed from the LCD (the direction indicated by the
"LOCK➡" symbol on the Installation Bracket).
Part Names
8
7
Slide this product in the opposite direction of the "LOCK
➡" symbol.
Installation Bracket Hooks
① System Indicator
② Mini USB Terminal (mini-B type)
The Cigarette Lighter Power Cable is connected
to this terminal. You can also connect this
product to your computer with a commercially
available USB cable.
③ Speaker
④ Function Buttons
⑤ Power Button/Function Button
⑥ Microphone
⑦ microSD Card Slot
1
(Front)
2
3
6
5
4
(Back)
9
9
b
a
⑧ Reset Button
Press this button with the tip of a ballpoint pen
to reset this product. (When the product is reset,
the power turns off. To turn the power back on,
press and hold the power button.)
⑨ Installation Bracket Slots
⑩ Lens
⑪ Indicator
The indicator is illuminated when powered.
Advertisement
