Advertisement
Available languages
Available languages
− adding approx. 3-5 drops of pneu-
matic oil by hand every 15 min-
utes of use (constant operation)
to the air inlet.
1.
Installing or changing the saw blade.
− Loosen hexagon socket screw
locking the saw blade.
− Insert or replace the saw blade.
− Retighten hexagon socket screw.
− Check to see that the saw blade
is properly secured.
2.
Adjusting the hoop guard:
− Loosen both Phillips screws for
hoop guard adjustment.
− Adjust hoop guard to desired
depth of cut.
− Retighten both Phillips screws.
3.
Adjust working pressure at the com-
pressor (see Technical Specifica-
tions for max. permissible working
pressure).
4.
Connect tool with quick coupler to
the air supply.
5.
To start:
− Push safety forward.
− Press throttle fully down.
6.
Hold saw at right angle to the work-
piece and and apply slight pressure
while cutting.
A
Caution!
•
If too much pressure is applied on
the saw blade, it may overheat and
break. With too little pressure there
9. Technical Specifications
Model
Air consumption
Max. permissible working pressure
Stroke
Number of strokes
Maximum cutting capacity, steel
Maximum cutting capacity, aluminium
Minimum hose size (inner)
Vibration (effective value of weighted acceleration)
Sound power level L
WA
Sound pressure level L
PA
Dimensions:
length x width x height
Weight
is no sufficient cutting capacity,
resulting likewise in an overheating
of the saw blade.
•
If the saw blade jams while cutting:
− Release throttle lever immedi-
ately.
− Remove cause for jamming.
− Commence cutting only after saw
blade has been entirely freed.
7.
Release throttle lever to turn OFF.
5. Care and Maintenance
A
Danger!
Always disconnect from air
supply before servicing.
Repair and maintenance work other
than described in this section must
be carried out by qualified specialists
only.
•
Check all screwed connections for
tightness, tighten if necessary.
•
If the tool is not lubricated by a serv-
ice unit or line lubricator, add 3-5
drops pneumatic oil to the air inlet
every 15 minutes of use (constant
operation).
•
Do not store tool unprotected out-
doors or in damp environment.
6. Available Accessories
•
Pneumatic oil 0.5 litre
Special lubricant for air tools, serv-
ice units and line oilers.
Stock-no. 090 100 8540
•
Line oiler R3/8" female
For fitting directly to air tools. Oil
level
can
through sight glass.
Stock-no. 090 105 4592
•
Swivel-type air inlet
DKG 1/4"
For fitting directly to air tools.
Improves tool manoeuverability.
Stock-no. 090 106 0991
7. Repairs
A
Danger!
Repairs to air tools must be
carried out by qualified specialists
ONLY!
Air tools in need of repair can be send to
the service centre in your country. See
Spare Parts List for address.
Please attach a description of the fault to
the air tool.
8. Environmental Protection
The tool's packaging can be 100 % recy-
cled.
Worn out machines and accessories
contain considerable amounts of valua-
ble raw and plastic materials, which can
be recycled.
These instructions are printed on paper
produced with elemental chlorine free
bleaching process.
KS 6000 Set
l/min
bar
mm
min
mm
mm
mm
2
m/s
dB (A)
dB (A)
mm
260 x 40 x 80
kg
ENGLISH
always
be
checked
470
6.3
10
10000
2.91
3.26
9
< 9
85
0.67
9
Advertisement
Chapters
