Related Manuals for Elektra Beckum TKHS 315
Summary of Contents for Elektra Beckum TKHS 315
- Page 1 A0250IVZ.fm TKHS 315 (AUS) Operating Instruction ....3...
- Page 2 U2a0250.fm...
-
Page 3: Scope Of Delivery
XA0034AUS1.fm Operating Instruction ENGLISH ENGLISH 1. Scope of delivery Table insert Leg (4x) Fence carrier, lower / mitre fence Riving knife Handwheel / blade tilt Fence carrier, upper / Blade guard Handwheel / blade rise and fall mitre fence Saw blade Chipcase guide panel, front Mitre fence extrusion Suction hose... -
Page 4: Machine Overview
ENGLISH 2. Machine overview Saw blade ∅315 mm Stand with multiple reinforce- ment beads for high stability Rip fence Mitre fence Table top of galvanized steel plate – high stability under load Maintenance-free induction and permanent protection motor against corrosion Handwheel for setting the depth of cut steplessly from 0 –... -
Page 5: Table Of Contents
ENGLISH ronment. Table of Contents 4. Safety instructions Prevent body contact with earthed objects such as radiators, pipes, cooking Scope of delivery ......3 Specified conditions of stoves, refrigerators when operating this Machine overview ....... 4 tool. Please read first!......5 This machine is intended to rip and Do not use the power cable for purposes crosscut grown timber, faced boards,... -
Page 6: Symbols Used Throughout These Instructions
ENGLISH Hazard generated by insuffi- Caution! cient personal protection gear! Risk of material damage. Wear hearing protection. Note: Wear safety glasses. Additional information. Wear dust mask. Safety devices Wear suitable work clothes. When work- ing outdoors wearing of non-slip shoes is Riving knife recommended. -
Page 7: Assembly
ENGLISH In order to prevent the set blade tilt to The chipcase guide panels (55) and (57) change during cutting, its position is are installed on the underside of the locked with the lock lever (50). table top (58). Place table top with the folds facing Handwheel for setting the depth of up on a sturdy support. - Page 8 ENGLISH Bevel tilt setting device installation Item Description Qty. Hex. socket counter- sunk head screw M8 x 35 Cup spring 8.216 Outer clamping piece Inner clamping piece Hexagon nut, prevail- ing torque-type, M8 Setting tube Pinion shaft Adjust bearing plates so that the Threaded rod their lower edges are parallel with Setting knob...
- Page 9 ENGLISH Installation of sliding plate port to the chipcase Item Description Qty. Sliding plate Cup square neck screw M5 x 16 Flange nut M5 • Install the sliding plate (91) on the outside of the chipcase, using two each saucer-head screws (92) and Fasten the thus prepared turning flange nuts (93).
- Page 10 ENGLISH − the wide sides of the stanchions Item Description Qty. face the table panel; Hex. socket counter- − the nibs and recesses must fit sunk head screw into each other; M6 x 25 − fit hexagon head screws (104) Guide bracket into holes from the outside;...
- Page 11 ENGLISH − in its lateral alignment. Saw blade alignment Turn flat head screw clockwise (viewed from top) until it stops, and If necessary, crank the saw blade Distance to the saw blade: place table insert extrusion flush into fully up using the handwheel to The distance between the saw blade's the table top's slot.
- Page 12 ENGLISH Fit other end of the suction hose to does not touch any of the teeth set to the the dust extraction port (133) on the right. Otherwise the straightedge is not chipcase. exactly parallel with the saw blade. Hook the suction hose into the hose carrier (132).
-
Page 13: Mains Connection
ENGLISH Accessory holder installation 8. Operation Note: Item Description Qty. Check with your local Electricity Risk of injury! Hexagon head screw Board or electrician if in doubt whether This saw may only be operated M6 x 50 your house service connection meets by one person at a time. -
Page 14: Setting The Depth Of Cut
ENGLISH − hoses must fit the outer diameter Adopting the fence extrusion to the of the dust extraction ports (blade workpiece height: guard 36 mm; chipcase 100 mm); ≥ − air flow volume 460 m − vacuum at dust extraction port of ≥... -
Page 15: Sawing With The Mitre Fence
ENGLISH Sawing with the mitre 10.1 Saw blade change Danger! Use only suitable saw blades fence Danger! (see "Available accessories") – when Swing mitre fence on the table top. Directly after cutting the saw using unsuitable or damaged blades blade can be very hot – burning haz- Set to desired mitre angle and lock parts could be explosive-like hurled ard! Let a hot saw blade cool down. -
Page 16: Saw Storage
ENGLISH Apply a light coat of Care and Main- 13. Available accessories tenance Spray. For special tasks the following accesso- Install saw blade and tighten arbor ries are available at your specialist bolt. dealer – see back cover for illustrations: Install the table insert. -
Page 17: Technical Specifications
ENGLISH 14. Technical specifications TKHS 315 2.2 W Voltage 230 V / 1~50 Hz Nominal current 10.6 Fuse protection min. 1 - 16 (time-lag) Degree of protection IP 54 Motor speed 2800 Motor capacity input capacity P 2.2 kW S6 40% power output P 1.5 kW S1 100%... - Page 18 X_1Leer.fm...
- Page 19 U3a0250.fm 091 005 7154 091 005 3680 091 001 4030 091 003 1260 091 101 8691 091 000 0250 091 000 0195 091 001 2282 091 005 3353 091 005 3361 091 005 3345...
- Page 20 U4BA_EB3.fm www.elektra-beckum.de...
Need help?
Do you have a question about the TKHS 315 and is the answer not in the manual?
Questions and answers