Press Arm Main Frame 1 - Nautilus NS-4000 Assembly Instructions Manual

step
2
72
120
1 1/4"L
20
109
4"L
19
Step #2 Materials:
# Component
17 Press Arm Main Frame
18 Press Arm Base
19 Press Arm Seat Frame
20 Seat Adjuster
21 Press Arm
22 Press Arm Top Beam
23 Press Arm Range of Motion
24 Press Arm Pivot Shaft
25 Left Press Arm Handle
26 Right Press Arm Handle
34 Guide Cable Upper Bracket
71 Press Arm Back Pad
72 Press Arm Seat Pad
101 Guide Cable
102 Hex Bolt - 1/2" x 2 3/4"L ThreadLock
106 Hex Bolt - 3/8" x 5"L
109 Hex Bolt - 3/8" x 4"L
112 Hex Bolt - 3/8" x 3"L
116 Hex Bolt - 3/8" x 2 1/4"L
120 Hex Bolt - 3/8" x 1 1/4"L
124 Hex Bolt - 3/8" x 1"L ThreadLock
127 Button Head Screw 3/8" x 3/4"L ThreadLock
129 1/2" Flat Washer
130 3/8" Flat Washer
132 Half Circle Washer
135 3/8" Lock Nut
142 Set Screw 5/16" x 1/4"L ThreadLock
26
71
116
2 1/4"L
C
A
112
3"L
B
B
106
135
18
124
1"L
25
24
142 1/4"L
132
127
3/4"L
A 130
17
3
5"L
A. Attach the Press Arm Base (18) to the Main Base using the
hardware shown. Do not tighten hardware.
B. Attach the Press Arm Top Beam (22) to the Main Top Frame
Qty
using only the screw and washer located away from the Pec Fly
Beam. Do not tighten screw until after completing step C.
1
C. Place end "AA" of the Guide Cable (101) in the slot on the
1
Upper Bracket (34) as shown. Attach the Upper Bracket (34) to
1
the Main Top Frame and Press Arm Top Beam (22) using the
1
1 hardware shown. Tighten hardware securely. Note: Guide
1
Cable (101) will not be fully assembled until step 15.
1
D. Attach the Press Arm Main Frame (17) to the Press Arm Base
1
(18) and the Press Arm Support Upright (3) using the hardware
1
shown. Do not tighten hardware. NOTE: Be sure to install the
1
hardware with the bolt head to the inside as shown in detail B.
1
Otherwise, the end of the bolt will interfere with the weight stack.
1
E. Attach the Press Arm Seat Frame (19) to the Press Arm Base
1
(18) using the hardware shown. Tighten all hardware in
1
instructions A-D securely.
2
F. Attach the Press Arm Range of Motion (23) and the Press Arm
2
(21) to the Press Arm Main Frame (17) using the Press Arm
2
Pivot Shaft (24). Align the Pivot Shaft (24) and secure by
1
tighten the Set Screws (142) securely.
2
G. Attach the left and right Press Arm Handles (25)(26) to the
4
Press Arm (21) using the hardware shown. Make sure that the
2
handles point away from each other. Tighten hardware securely.
4
2 H. Attach the Press Arm Seat Pad (72) to the Seat Adjuster (20)
20
and slide the adjuster tube into the Press Arm Seat Frame (19)
4
as shown. Tighten hardware securely.
7
I. Attach the Press Arm Back Pad (71) to the Press Arm Main
4
Frame (17) using the hardware shown in detail A. Tighten
hardware securely.
8
1676mm (66")
21
AA
22
C
129
A A
23
1 1/4"L
120
A A
B
NS-4000
34
102
2 3/4"L
101
NECESSARY BOLT
ORIENTATION