Download Print this page

HP Kayak XW 04xx Installation Manual

Hp kayak xw series 0480, hp visualize fx6 texture module installation guide
Hide thumbs

Advertisement

Quick Links

HP Kayak XW Series 0480 PC Workstation—
HP VISUALIZE fx6 Texture Module

Advertisement

loading

  Also See for HP Kayak XW 04xx

  Related Manuals for HP Kayak XW 04xx

  Summary of Contents for HP Kayak XW 04xx

  • Page 1 HP Kayak XW Series 0480 PC Workstation— HP VISUALIZE fx6 Texture Module...
  • Page 2: Important Safety Instructions

    HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module Important Safety Instructions Important Safety Instructions Please read the following safety information first. CAUTION Static electricity can damage electronic components. Use an electrostatic bracelet if you have one. Turn all equipment OFF.
  • Page 3 HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module Introduction Introduction The HP VISUALIZE fx6 Texture Module is an add-on accessory for the HP VISUALIZE fx6 graphics board. The HP VISUALIZE fx6 Texture Module provides: Accelerated hardware texture mapping •...
  • Page 4: Installing The Texture Module

    HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module Installing the Texture Module Installing the Texture Module CAUTION Be very careful when handling the VISUALIZE fx6 board. Bumping, bending or dropping the board can cause irreparable damage. Removing the VISUALIZE fx6 Graphics Board 1 Switch off the display and PC Workstation, and disconnect all power cords and any telecommunication cables.
  • Page 5 HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module Installing the Texture Module WARNING Before handling the VISUALIZE fx6 graphics board, first wait until the board has cooled down completely before touching it. The graphics board can become hot during use. 4 Remove the two accessory slot screws and the retaining screw that holds the board in place and, carefully ease the board up and out of the PC Workstation’s case using the board’s strengthening bar.
  • Page 6 HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module Installing the Texture Module Adding the Texture Module to the VISUALIZE fx6 Board 1 Remove the two screws from the board’s strengthening bar, and then remove it from the VISUALIZE Fx6 board. (You can use a Torx screwdriver or a flat-blade screwdriver of the correct size.) Strengthening Bar Terminator...
  • Page 7 HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module Installing the Texture Module 4 Carefully line up the connectors on the texture module and the VISUALIZE fx6 board. Then using both thumbs, press the texture module into place. Texture Module Texture Module Connectors...
  • Page 8 HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module Installing the Texture Module Replacing the VISUALIZE fx6 Graphics Board 1 First ensure that the system board data cables are correctly routed and flat against the system board so that they do not obstruct the VISUALIZE fx6 graphics board.
  • Page 9: Checking The Installation

    HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module Checking the Installation Checking the Installation The fx6 texture module is automatically detected by the VISUALIZE fx6 driver. No software configuration is necessary. To check that the texture module is correctly installed: 1 Switch on your PC Workstation.
  • Page 10: Hardware Warranty

    The type of service provided is return to an HP or repair-authorized reseller service-center. At Hewlett-Packard’s discretion, a defective accessory will be repaired or replaced by a new unit, either of the same type or of an equivalent model.

This manual is also suitable for:

Kayak xw series 0480