Table of Contents
Advertisement
EZ-Programming
There are 9 user-selectable options so you can
customize your Solo S3 for your own preferences.
The Mode button ("M") and the "VOL" buttons (up
or down arrows) are used to enter the programming,
REVIEW your current program settings, and to
CHANGE any settings as desired. The letters "PGM"
(program), RVW (review), and CHG (change) are
located on the front of the detector, and are
highlighted in blue graphics. Pages 16-19 explain
each option in more detail.
How to use EZ-Programming
1 To enter Program Mode, press and hold either
of the "VOL" (up or down) buttons, and the "M"
(mode) down for 2 seconds. The unit will beep
twice, and will display the word "Program."
2 Then press the RVW button to review the
current settings. You can either tap the button to
change from item to item, or press and hold the
button to scroll through the items.
3 Press the CHG button to change any setting.
You can either tap the button to change from
setting to setting, or hold the button to scroll
through all the options.
4 To leave the Program Mode, simply wait 8
seconds without pressing any button. The unit
will display Complete, beep 4 times, and return
to normal operation.
To quickly reset Solo S3 to the factory program
settings, press and hold the Mute and M (Mode)
buttons while turning Solo S3 on.
Example of EZ-Programming
Here is how you would turn Solo S3's AutoMute
feature off.
1 Enter the Program Mode by holding one of the
VOL buttons and "M" (mode) button down for 2
seconds. Solo S3 will beep twice and display
"Program."
2 Then hold the RVW button down. Solo S3 will
scroll through the categories, starting with Pilot
options, Auto-Power, Power-On sequence, Signal
Strength Meter, AutoMute, Tones, City sensitivity,
Brightness, and Bands.
3 Release the RVW button when Solo S3 shows the
AutoMute item. Since the factory setting is for
AutoMute to be on, Solo S3 will display "aMute
ON." (If you accidentally go to the next category,
press the opposite "VOL" button to go back.)
4 Press the CHG button to change from "aMuteON"
to "aMuteOFF."
5 To complete the Programming, simply wait 8
seconds without pressing any button. Solo S3 will
display Complete, beep 4 times, and return to
normal operation.
14
Overview of EZ-Programming
Press the RVW button to go
your setting within a category
PILOT LIGHT
Pilot HWY
Pilot H
(Options using
12-volt SmartCord)
Pilot H.>
Pilot +
Pilot +.>
Pilot +>
AUTO POWER
POWER-ON SEQUENCE
PwrOn STD
PwrOn FST
SIGNAL STRENGTH METER
Meter STD
Meter EXP
AUTOMUTE
aMute ON
aMute OFF
AUDIOTONES
CITY MODE SENSITIVITY
BRIGHTNESS
BANDS
Bands ALL
Bands MOD
*
Solo S3's Factory Settings
To reset Solo S3 to its original factory
settings, press and hold the Mute and
M (Mode) buttons while turning Solo
S3 on. Solo S3's display will provide a
"Reset" message, accompanied by an
audible alert, acknowledging the reset.
Press the CHG button to change
from one category to the next
*
Full word:Highway or Auto or City
Letter:H or A or C
Letter,with scanning dot
Symbol:+ or • or --
Symbol,with scanning dot
Scanning symbol
*
aPwr Motn
Uses motion to turn Solo S3 off
aPwr Time
Uses time to turn Solo S3 off
aPwr Off
Turn Solo S3 on and off manually
*
Standard power-on sequence
Fast power-on sequence
*
Standard signal strength meter
Expert Meter
*
AutoMute on
AutoMute off
*
Tone STD
Standard tones
Tone LOUD
Loud tones
*
City STD
Standard City mode sensitivity
City LoX
Low X-band sensitivity in City Mode
City NoX
No X-band sensitivity in City Mode
*
Brt AUTO
Brightness is controlled automatically
Brt MIN
Minimum brightness when turned on
Brt MED
Medium brightness when turned on
Brt MAX
Maximum brightness when turned on
Brt DARK
Full Dark Mode when turned on
*
All bands enabled
One or more bands are disabled
Turn bands"ON"or"OFF"by
pressing the Mute button
*
X ON
OFF
or
X-band detection on
*
K ON
OFF
or
K-band detection on
*
Ka ON
OFF
or
Ka-band detection on
*
LSR ON
OFF
or
Laser detection on
*
SWS ON
OFF
or
SWS detection off
*
VG2 ON
OFF
or
VG2 detection off
15
Advertisement
Table of Contents
