Download Print this page

NEC MD211G5 User Manual

21" 5mp medical diagnostic display (fda pending)
Hide thumbs

Advertisement

Quick Links

MD211G5

Advertisement

loading

  Related Manuals for NEC MD211G5

  Summary of Contents for NEC MD211G5

  • Page 1 MD211G5...
  • Page 2 Disclaimer * Windows and MS-DOS are trademarks and/or registered trademarks of Microsoft Corporation in the United States and/or other countries. * VESA is a trademark of the Video Electronics Standard Association. * All other products and company names are trademarks of their respective owners.
  • Page 3 English...
  • Page 4: Table Of Contents

    CAN/CSA-C22.2 No. 60601-1:08 Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway, Spain, Sweden, U.K.
  • Page 5: Registration Information

    Declaration Declaration of the Authorized Representative Declaration of the Authorized Representative Means of Conformity NEC Display Solutions Europe GmbH declares that the product listed is in conformity with the essential requirements and Device Classifi cation: Class I, non-measuring function provisions of the Council Directive 93/42/EEC, including the Applicable Rules: Annex IX, Rules 1.4 (Section 1)
  • Page 6 WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
  • Page 7: Intended Use

    To secure full functionality of this display, only NEC approved display controller models for connection with the fi nal system must be used.
  • Page 8: Recommended Use

    WARNING: To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth. WARNING: No modifi cation of this equipment is allowed. WARNING: For EMC details information, please contact NEC local authority. •...
  • Page 9 NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
  • Page 10: Contents

    Contents Your new NEC monitor box* should contain the following: • MD211G5 monitor with tilt/swivel/pivot/height adjust stand • Power Cord • Video Signal Cable (DVI-D to DVI-D cable)* • DisplayPort cable • USB Cable • Quick Reference Guide Power Cord*...
  • Page 11: Quick Start

    Quick Start To connect the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended Use” before installation. In order to display the maximum resolution, a display controller that can output a resolution of 2048 x 2560 is needed. 1.
  • Page 12 5. To keep the cables neatly organized, place them into the cable management system that is built into the stand. Place the cables in the hooks fi rmly and evenly (Figure D). Figure D 6. Slide down the cable cover (Figure E). 7.
  • Page 13: Controls

    Controls 1 Power Switch To turn the monitor on and off. 2 LED Indicates that the power is on. Turns off automatically, when the luminance is stabilized. 3 Front Sensor For luminance stabilization and calibration. 4 Ambient Light Sensor Measures ambient light during calibration process. 5 + (plus) Button To open the OSD (On Screen Display) click –...
  • Page 14: Specifi Cations

    Specifi cations Monitor Specifi cations MD211G5 Notes LCD panel color Clear Base 21.3-inch (54 cm), monochrome, TFT active matrix, anti-glare Pixel pitch (H x V) 0.165 x 0.165 mm Display area (H x V) 337.9 x 422.4 mm Pixel (H x V) 2048 x 2560 Grayscale 256 steps of gray out of a palette of 12277...
  • Page 15: Additional Installation Information

    Additional Installation Information Advanced OSD Several control functions are available by entering the advanced OSD. These control functions are additional OSD menu items, which are always accessible after opening the standard OSD. Control Function Description EDID Change the picture format to be recognized by the operating system •...
  • Page 16 3. After selecting your preferred EDID mode, hold down the (+) plus button and the (-) minus button simultaneously for over 2 seconds again. Then displayed (Information) OSD and Selected (Landscape) EDID data is displayed as (FIXED). Then confi rm the EDID line (Portrait/Landscape) on the “INFORMATION” OSD. 4.
  • Page 17 How to Change Confi guration (Preset 1, 2, 3) The NEC model MD211G5 is shipped with 3 factory preset confi gurations, as listed below. Luminance (cd/m Confi guration Gamma Remark Maximum Minimum Ambient DICOM [Factory Default] DICOM DICOM The confi guration can be changed via an OSD menu. The confi guration 1 parameters may be modifi ed anytime by a new display calibration.
  • Page 18 Performing the DICOM conformance test This function is available only when the display has been calibrated to DICOM GSDF. Performing the DICOM conformance test ensures DICOM conformance of the display by measuring and checking the display properties. The DICOM conformance test is recommended to be performed after 60 minutes of continuous lighting time of the backlight of the LCD panel.
  • Page 19 4. Showing the test results When the measurement is completed, the test results are shown. Test results Test results Passed: Max. deviation ≤ 10% Failed: Max. deviation > 10% Canceled: Test has been canceled. Passed(!), Failed(!) “(!)” following Passed and Failed indicates that the recommended condition has not been met. (The test was performed in less than 60 minutes of continuous lighting time of the backlight.) If the test is continuously performed in less than 30 seconds, “Unstable”...
  • Page 20: Antitheft Security Slot

    Attaching a wall mount or multi-display mounting arm The tilt and swivel stand, as shipped with the display, is interchangeable with commercially available wall mounts or multi-display mounting arms that: • Come with a mount plate with 4 slotted screw holes at 100 mm x 100 mm and •...
  • Page 21: Manufacturer's Recycling And Energy Information

    Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.
  • Page 22 NEC Display Solutions, Ltd. NEC Display Solutions of America NEC Display Solutions Europe GmbH 4-28, Mita 1-chome, Minato-ku, 500 Park Blvd. Suite 1100 Itasca, Landshuter Allee 12-14 Tokyo, Japan Illinois 60143 D-80637 Muenchen Germany Phone: +1-630.467.3000 Phone: +49(0)89/99699-0 Fax: +1-630.467.3010 Fax: +49(0)89/99699-500 Vol.