NEC MD211G3 Quick Reference Manual
21" grayscale 3-megapixel medical diagnostic monitor
Hide thumbs
Also See for MD211G3:
- Installation & maintenance manual (32 pages) ,
- Brochure & specs (3 pages) ,
- Specification (6 pages)
Related Manuals for NEC MD211G3
Summary of Contents for NEC MD211G3
- Page 1 MD211G3 MD211G3 paper manual.indb 1 MD211G3 paper manual.indb 1 3/27/12 11:18:27 AM 3/27/12 11:18:27 AM...
-
Page 2: Registration Information
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: NEC Display Solutions of America, Inc. Address: Tel. -
Page 3: Energy Saving
Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life. - Page 4 MD211G3 paper manual.indb 4 MD211G3 paper manual.indb 4 3/27/12 11:18:29 AM 3/27/12 11:18:29 AM...
-
Page 5: Table Of Contents
UL MARK CERTIFICATION, ANSI/AAMI ES60601-1:2005 cUL, CAN/CSA-C22.2 NO.60601-1:08 Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway, Spain, Sweden, U.K. - Page 6 TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
-
Page 7: Intended Use
The MD211G3 Grayscale display is intended to be used for displaying and viewing of digital images for diagnosis by trained physicians. To guarantee the display performance as specifi ed, it must only be used in conjunction with NEC approved display controllers. MD211G3 cannot be used for a life-support system. -
Page 8: Recommended Use
WARNING: To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth. WARNING: No modifi cation of this equipment is allowed. WARNING: For EMC details information, please contact NEC local authority. •... - Page 9 Get regular eye checkups. NOTE: This model is set up in the factory so that the NEC logo is briefl y displayed after the monitor is powered on. This feature can be turned on or off in the Advanced OSD.
-
Page 10: Contents
Contents Your new NEC monitor box* should contain the following: • MD211G3 monitor with tilt/swivel/pivot/height adjust stand • Power Cord • Video Signal Cable (DVI-D to DVI-D cable)* • DisplayPort cable • USB Cable • Quick Reference Guide • CD-ROM x 2... -
Page 11: Quick Start
Quick Start To connect the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended Use” before installation. In order to display the maximum resolution, a display controller that can output a resolution of 1536 x 2048 (in portrait mode) or 2048 x 1536 (in landscape mode) is needed. - Page 12 4. Connect all cables to the appropriate connectors (Figure C.1). When using the USB cable, connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the computer (Figure C.1a).
- Page 13 7. Slide down the cable cover (Figure D.1). 8. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet. NOTE: Please refer to the Caution section of this manual for proper selection of an AC power cord. 9.
-
Page 14: Controls
Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: To access the OSD menu, press the EXIT button. To change the signal input, press the SELECT button. All buttons are located at the back of the monitor. The Key Guide appears pressing any button when not in the OSD control menu. -
Page 15: Setting Osd Language
SETTING OSD LANGUAGE • Set the OSD language before using OSD functions. • Use the control keys (LEFT/RIGHT or UP/DOWN or EXIT) to access the “LANGUAGE SELECTION” menu. • Press the LEFT/RIGHT or UP/DOWN buttons to select the desired OSD language. •... -
Page 16: Specifi Cations
1920 x 1200* at 60 Hz 2048 x 1536 at 30 Hz to 60 Hz (Reduced Blanking) 2048 x 1536 at 60 Hz (Reduced Blanking)... NEC DISPLAY SOLUTIONS recommended resolution 1024 x 1280 at 60 Hz* 1200 x 1600 at 60 Hz* 1536 x 2048 at 60 Hz (Reduced Blanking)... - Page 17 MD211G3 paper manual.indb 13 MD211G3 paper manual.indb 13 3/27/12 11:19:14 AM 3/27/12 11:19:14 AM...
- Page 18 4-28, Mita 1-chome, Minato-ku, Tokyo, Japan Printed on recycled paper MD211G3 paper manual.indb 14 MD211G3 paper manual.indb 14 NEC Display Solutions of America, Inc. NEC Display Solutions Europe GmbH 500 Park Blvd. Suite 1100 Itasca, Landshuter Allee 12-14 Illinois 60143...