Sharp FO IS125N - B/W Laser - All-in-One Service Manual page 66

FO-IS125N
SW22 No. 4, No. 5 Busy tone detection frequency
To select frequency range of signals to be detected as Busy Tone.
SW22 No. 6 ~ No. 8 Reserved
SW23 No.1 ~ No. 4 Number of rings for auto-receive (0: No ring
receive)
When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from zero to nine
rings using a binary number. If the soft switch was set to 1, a direct
connection is made to the facsimile. If it was above 9, receive rings are
set to 9.
SW23 No.5 ~ No. 8 Distinctive ring
When the ringing setting is turned off, all of the CI signal are received.
When any of the standard, and ring patterns 1 through 5 is selected for
the ringing setting, only the selected CI signal is received.
CI signal patterns
The CI signal patterns consists of the standard pattern, and ring pat-
terns 1 through 7. The standard pattern is the conventional one.
SW24 ~ SW36 No. 1 ~ No. 8 Reserved
SW37 No. 1, No. 2 Delay timer before line connect in auto dial
Set a time period between start of dial operation and line connection in
the auto dial mode.
SW37 No. 3, No. 4 Delay timer after line connect in auto dial
Set a time period between dial-up line connection and dial data trans-
mission in the auto dial mode.
SW37 No. 5, No. 6 Calling time
Set the call time for dialing in the auto dial mode.
SW37 No. 7, No. 8 CNG timing
Set a time period between dialing in the auto dial mode and CNG sig-
nal transmission.
SW38 No. 1 Dial tone detection (before auto dial)
When set to "1", a number is dialed after detecting the dial tone.
SW38 No. 2 Busy tone detection (after auto dial)
When set to "1", the busy tone is detected after dialing a number.
SW38 No. 3 Recall control (for FCC part68)
Recalling fixed only one time when dialing was unsuccessful without
detecting busy tone signal.
SW38 No. 4 ~ No. 8 Reserved
SW39 No. 1 ~ No. 8 Reserved
SW40 No. 1 ~ No. 6 Reserved
SW40 No. 7, No. 8 Paper size
The paper size is set.
SW41 No. 1 Reserved
SW41 No. 2 Dial pause
Pauses can be inserted between telephone numbers of direct dial con-
nection. Selection of 4 sec or 2 sec pause is available.
SW41 No. 3, No. 4 Line density selection
Used to set the transmission mode which is automatically selected
when the Resolution key is not pressed. In the copy mode, however,
the fine mode is automatically selected unless the Resolution key is
manually set to another mode.
SW41 No. 5 Activity report print
This soft switch is used to select: whether or not to print out the activity
report when the memory is full. An activity report can be printed when
the following key entry command is mode.
"FUNCTION ", "↓", "↓", "→"
After producing the activity report, all the data in the memory will be
cleared. When the switch function is set to "0" (no), the data in the
memory will be deleted from the oldest as it reaches the maximum
memory capacity.
SW41 No. 6 Daylight saving
The daylight saving function ON/OFF is set.
SW41 No. 7 Print setting of received fax for Receive Fax to e-mail
This soft switch is used to select before.
0: Received FAX is always printed when Receive Fax to e-mail func-
tion worked.
1: Received FAX is printed only transfer error when Receive Fax to e-
mail function worked.
SW41 No. 8 Reserved
SW42 No. 1, No. 2 Reserved
SW42 No. 3, No. 4 Ringer volume
The calling sound volume of CI signal receiving is set.
SW42 No. 5, No. 6 Speaker volume
The line monitor volume is set.
SW42 No. 7, No. 8 Reserved
SW43 No. 1 ~ No. 8 Reserved
SW44 No. 1 ~ No. 3 Reserved
SW44 No. 4 ~ No. 6 CI signal min. OFF time
Used to set the min. OFF time criterion of the CI signal.
SW44 No. 7, No. 8 Reserved
SW45 No. 1 ~ No. 8 Reserved
SW46 ~ SW54 No. 1 ~ No. 8 Reserved
SW55 No. 1, No. 2 Reserved
SW55 No. 3 Digital cable equalizer for reception
Digital cable equalizer for reception
0: OFF
1: ON
2 – 53