Page of 8

HP LC2000r - NetServer - 128 MB RAM Introduction Manual

Hp netserver lxr pro netraid config guide for windows nt4.0 clusters.
Hide thumbs
   
(see Version History at the end of this document)
Introduction
This document defines the supported HP NetServer LXr Pro configurations for Microsoft Cluster Server.
These configurations minimize single points of failure, provide maximum availability, and have been
certified by Hewlett-Packard and Microsoft. This guide is prescriptive; it describes the HP NetServer LXr
Pro configurations supported by HP. Any configuration not expressly allowed by this guide will not be
supported by HP.
What's Defined
Cluster
SPUs
Local and Shared Storage
Intra-cluster and Client LANs
Cluster
Type of SPUs
Number of nodes
Shared Storage
LANs:
Client LAN
Intra-cluster
(Heartbeat) LAN
Power source
System software:
Navigator version
Operating System
Service pack
SPU
Model
with
NetRAID (HP Rack Storage/8)
Cluster Configuration Guide
04 April 2000
HP NetServer LXr Pro Model 1
Each node must be the same model SPU, but may have different size main
memory, cache, and number of CPUs (at least 2 are required).
2
Shared Storage HP Rack Storage/8 with HP NetRAID controller and HP
disks. See Shared Storage below.
Any NIC that is HP and Microsoft approved. See
HP D5013A or J3171A only with crossover cable. See
below.
Direct from power mains, power conditioner or uninterruptable power
supply (UPS) using any power conditioner or UPS.
G.01.00 or later
Microsoft Windows NT Server 4.0, Enterprise Edition.
SP3 and hotfix "clusfixi", or later. The hotfix is not required but is
recommended for clusters using 9.1GB and higher capacity drives.
HP NetServer LXr Pro Model 1
1
Client LAN
below.
Intra-cluster LAN

Advertising

   Related Manuals for HP LC2000r - NetServer - 128 MB RAM

   Summary of Contents for HP LC2000r - NetServer - 128 MB RAM

  • Page 1: Hp Netserver Lxr Pro

    These configurations minimize single points of failure, provide maximum availability, and have been certified by Hewlett-Packard and Microsoft. This guide is prescriptive; it describes the HP NetServer LXr Pro configurations supported by HP. Any configuration not expressly allowed by this guide will not be supported by HP.

  • Page 2

    Clock speed 200 MHz. No. of CPUs 2 – 4 (at least 2 are required) BIOS version 1.00.09.CDOL or later CPU cache Any size 128 MB minimum. Must be HP. No. of power supplies Hot swap cages May use for local storage; but not use for shared storage. Local storage Internal or external, using any controller.

  • Page 3

    Disk drives: HP 2.1 GB Hot-Swap Ultra SCSI Disk Module D3582C HP 4.2 GB Hot-Swap Ultra SCSI Disk Module D3583C HP 4.2 GB 10K rpm Hot-Swap Ultra SCSI Disk Module D4903A HP 9.1 GB Hot-Swap Ultra SCSI Disk Module D4289A HP 9.1 GB 10K rpm Hot-Swap Ultra SCSI Disk Module D6019A HP 18.2 GB Hot-Swap Ultra SCSI Disk Module D5039A RAID arrays...

  • Page 4: Shared Storage Cabling

    Shared Storage Cabling This part of the guide defines the allowable cabling configurations for clusters using the HP NetServer LXr Pro and HP Rack Storage/8s. Only these cabling configurations and cables are supported. NetRAID Ch. 0 NetRAID Ch. 1 NOTES: 1.

  • Page 5

    NetRAID Adapter 1, NetRAID Adapter 2, Ch. 0 (top) Ch. 0 (top) Ch. 1 (bottom) Ch. 1 (bottom) NOTES: 1. Configure cluster using 3 or 4 Rack Storage/8s. 2. Channel 0 and 1 of each NetRAID Adapter for each LXr must be connected together through the Rack Storage/8s as shown on the diagram.

  • Page 6

    Power Cabling to Separate Power Circuits (One HP NetRAID Adapter, Two RS/8s)

  • Page 7

    Power Cabling to Separate Power Circuits (Two HP NetRAID Adapters, Four RS/8s)

  • Page 8

    Version History 4 April 2000 Corrected reference to software version: “or later”. Added power diags. 18 November 1998 Initial release.

Comments to this Manuals

Symbols: 0
Latest comments: