Sharp FO-2970M Service Manual page 28

FO-2970MU
SW17 No. 1, No. 2 Speaker volume (3 stages)
Used to adjust sound volume from a speaker.
SW17 No. 3, No. 4 Hand-set receiver volume (3 stages)
Used to adjust sound volume from a handset receiver volume.
SW17 No. 5, No. 6 Ringer volume (4 stages)
Used to adjust ringing volume.
SW17 No. 7, No. 8 Key volume
Key buzzer volume:
The sound volume of key inputting buzzer and other buzzers is set.
SW18 No. 1 Reserved
Set to "1".
SW18 No. 2 Auto reception in PC I/F mode
Automatic receiving of I/F mode:
Which receives the call is determined.
SW18 No. 3 Summer time setting
The day light saving function ON/OFF is set.
SW18 No. 4 Sender's phone number setting
Whether the registered sender's phone number can be changed or not
is selected. If it is set at 1, the phone number of the sender can not be
registered or changed. Set 1 in order to prevent careless change of the
sender's phone number.
0: Change allowed
1: Cannot change
SW18 No. 5 Polling key
If this switch is set to 1, the last of Rapid key works as polling key.
SW18 No. 6 Activity report print
Whether the communication record table is automatically printed or not,
it is selected if the number of communication data is excessive. Regard-
less of the setting of this selection, communication record table can be
printed at all times by operating the keys.
FUNCTION + "2" + "#" + "START"
When the communication record table is printed, the memorized con-
tent of the data sent and received up to now will be all cleared (erased).
If No (non-printing) is set, the oldest data will be erased when the number
of memorized items is excessive.
0: No (first data lost when memory is full)
1: YES (when memory is full)
SW18 No. 7 Total communication hours and pages print
Whether the total time of communication and total number of sheets are
recorded in the communication record table or not is selected.
0: Recorded.
1: Not recorded.
SW18 No. 8 Line density selection
Used to set the transmission mode which is automatically selected when
the Resolution Key is not pressed. In the copy mode, however, the fine
mode is automatically selected unless the Resolution key is manually
set to another mode.
SW19 No. 1 , No. 2 Density adjustment (when Fine/STD mode)
This is used for density adjustment in fine/standard mode. Adjust the
density according to that of frequently used original.
Set to "Dark" for darker reading (either in the auto or the dark mode) of
light original. Set to "Light" for lighter reading (either in the auto or the
dark mode) of dark original.
Set to "Dark only in dark mode" for darker reading only in the dark mode.
SW19 No. 3 , No. 4 Density adjustment (when Half-tone mode)
This is used for density adjustment in the half tone. Setting procedures
are the same as SW19 No. 1, No. 2.
SW19 No. 5, No. 6 Reserved
Set to "0".
SW19 No. 7 Reserved
Set to "1".
SW19 No. 8 Reserved
Set to "0".
SW20 No. 1 ~ No. 6 Reserved
Set to "0".
SW20 No. 7 F.A.S.T (RMS) mode
Used to determine a function of remote maintenance system (F.A.S.T).
SW20 No. 8 Quick on-line
It is selected whether auto dial call is activated in the memory input
mode when one document is completely read or when all pages are
completely read.
SW21 No. 1, No. 2 Reserved
Set to "0".
SW21 No. 3 Reserved
Set to "1".
SW21 No. 4 ~ No. 8 Reserved
Set to "0".
SW22 No.1 ~ No. 8 Reserved
Set to "0".
SW23 No. 1 Automatic reduce of receive
If set to 1, it is reduced automatically.
SW23 No. 2 Cut off mode (COPY mode)
When in copy, if the scanned data is out of the range of recording, the
operator has one of the choices below using the switch
1: Continue: Data is printed onto the next page with the last 20mm
also printed at the beginning of the next page
0: Cut off. Data scanned out of the limit is cut off (a page is printed.)
SW23 No. 3, No. 4 Paper set size
At present a size of the record paper.
00: LETTER
01: LEGAL
10: A4
SW23 No. 5 ~ No. 8 Reserved
Set to "0".
SW24 No. 1, No. 2 DTMF detection time
Used to set detect time of DTMF (Dual Tone Multi Frequency) used in
remote reception (5
detection is caused by noises.
SW24 No. 3 Protection remote reception (5
Used to set the function of remote reception (5
the remote reception function is disabled.
SW24 No. 4 Reserved
Set to "0".
SW24 No. 5 ~ No. 8 Remote operation code figures by external tel
(0 ~ 9)
Remote operation codes can be changed from 0 through 9. if set to
greater than 9, it defaults to 9. The "5
2 – 24
). The longer the detection time is, the error
) detect
). When set to "1",
" is not changed.