Sharp FO-2970M Service Manual page 25

•
Soft switch function description
SW1 No. 1 ~ No. 4 Recall interval
Choice is made for a recall interval for speed, rapid dial numbers, ten
key +START and search + START. Use a binary number to program
this. If set to 0 accidentally, 1 will be assumed.
SW1 No. 5 ~ No. 8 Recall times
Choice is made as to how many recall times should be made. Use a
binary number to program this.
SW2 No. 1 Dial mode
Switch the type according to the telephone circuit connected to the fac-
simile.
0: TONE DIAL
1: PULSE DIAL
SW2 No. 2 Reception mode
Auto/manual receiving mode is set.
SW2 No. 3 ECM mode
Used to determine ECM mode function. Refer to the following table.
SW2- No. 3 ECM mode
SW6- No. 2 MH fixed
Compression method ECM MMR mode
ECM MR mode
ECM MMH mode
ECM MH mode
MR mode
MH mode
(Depending on remote machine)
SW2 No. 4 CNG detection in stand-by mode
The CNG signal detection function during stand-by stops.
0: Yes
1: No
SW2 No. 5 Polling security
This switch is employed to enable or disable the polling operation using
the ID code verification function, in order to prevent unauthorized poll-
ing operation.
SW2 No. 6 Automatic cover sheet
When "0" (=YES) is selected, the cover sheet is automatically sent after
transmission of the original to notify the receiver of the number of origi-
nal sheets transmitted.
SW2 No. 7 Junk fax function in manual reception
It is set whether JUNK-FAX is functioned in the manual receiving mode
or not.
SW2 No. 8 Anti junk fax function
This function is used to receive data from a specific remote machine
(station registered in entry mode). It is the function that refused a recep-
tion in the case that TSI of remote machine matched with fax number of
the station registered.
0: No
1: Yes
SW3 No. 1 ~ No. 4 Number of rings for auto receive
When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from one to nine rings
using a binary number. If the soft switch was set to 1, a direct connec-
tion is made to the facsimile. If it was set to 0 accidentally, receive ring is
set to 1. If it was above 9, receive rings are set to 9.
0 0 0 0 0 0
0 1 0 1 0 1
Yes No Yes No No No
Yes No Yes No Yes No Yes No
Yes Yes No No Yes Yes No
Yes Yes Yes Yes Yes Yes Yes Yes No
Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No
Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
SW3 No. 5 ~ No. 8 Automatic switching manual to auto receive mode
(0: OFF)
This setting allows machine to switch from manual to Auto Receive mode.
Setting this number to 0 forces machine to stay in Manual receive mode.
Entering the binary number 0 forces the machine to remain in the manual
answer mode. If a number between 1 and 9 is entered, the machine will
go into the answer mode after the given number of rings. However, it
can be used as an ordinary telephone if the handset is taken off the
hook before this programmed number is finished. If entry of a number
above 9 by accident, it will be set to 9. In this case, it must be corrected
to the proper number.
SW4 No. 1 ~ No. 3 Communication results printout
(transaction report)
Every communication, the result can be output. As usual, it is set to print
the timer sending communication error alone. If No.1 : 1 No.2 : 1 No.3 :
0 are set, printing is always on (printed ever if it is normally ended).
SW4 No. 4 Delay timer before line connect in auto dial
Delay time between the dial key input and line connection under the
auto dial mode.
SW4 No. 5, No. 6 Delay timer of after line connect in auto dial
Delay time between the line connection and dial data output under the
auto-dial mode.
SW4 No. 7, No. 8 Number of CNG detect (STAND-BY mode)
Used for detection of CNG in 1 to 4 pulses.
SW5 No. 1 Time format
When this switch is set to "0", time is displayed in 12-hour system.
When set to "1", 24-hour system.
2 – 21
0 0 1 1 1 1
0 1 0 1 0 1
No No No No No No
No No No No
No No No No No
No No No
000 : Error, timer and memory sending/receiving
010 : Sending
110 : Continuous printing
100 : Not printed
001 : Communication error
FO-2970MU
1 1 1 1
0 1 0 1
No No No No
No No No No
No No No No
No No No No