1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Fax Machine
  5. FO-2970M
  6. Service manual

Sharp FO-2970M Service Manual

Service manual
Hide thumbs Also See for FO-2970M:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual
Chapters 1, 3, 7 and 8 of this manual are omitted because they are partly common to the FO-2950MU. Please refer to
previous service manual UX-4000MU/FO-2950MU/C (00ZUX4000USME) for these chapters.
Difference between FO-2970MU and FO-2950MU
Control PWB
TEL/LIU PWB
Modem speed
CAUTION
This laser facsimile is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH or IEC60825-1 standard.
This means that this machine does not produce a hazardous laser radiation. The use of controls, adjustments or performance of
procedures other than those specified herein may result in hazardous radiation exposure.
This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved on the eyes retina, there is
danger of spot damage to the retina.
The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of servicing.
1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a unit, not an individual part.
2) Do not look into the machine with the main switch turned on after removing the toner/developer unit and drum cartridge.
3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected when removing and installing
the optical system.
4) The cover of Laser Printer Unit contains the safety interlock switch.
Do not defeat the safety interlock by inserting wedges or other items into the switch slot.
Laser Wave Length : 780 15 nm
Laser Pulse Times : (13.95
3 s)/7mm
Laser Output Power : 0.4 mW
0.05mW
Parts marked with " " is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintain-
ing the safety and performance of the set.
SERVICE MANUAL
FO-2970MU
DCEKC182PSCZZ
DCEKL259CSC01
33,600 bps
SHARP CORPORATION
No. 00ZFO2970USME
FACSIMILE
FO-2970M
MODEL
SELECTION CODE
U
FO-2950MU
DCEKC388NSCZZ
DCEKL222CSC01
14,400 bps
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
FO-2970MU
DESTINATION
U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Sharp FO-2970M

Summary of Contents for Sharp FO-2970M

  • Page 1 FO-2970MU SERVICE MANUAL No. 00ZFO2970USME FACSIMILE FO-2970M MODEL SELECTION CODE DESTINATION U.S.A. Chapters 1, 3, 7 and 8 of this manual are omitted because they are partly common to the FO-2950MU. Please refer to previous service manual UX-4000MU/FO-2950MU/C (00ZUX4000USME) for these chapters.

  • Page 2: Table Of Contents

    FO-2970MU CONTENTS CHAPTER 1. GENERAL DESCRIPTION [1] Specifications ..............1-1 [2] Operation panel .

  • Page 3: Chapter 1. General Description

    Length:5.5 to 39.4" mm (140 to 1,000mm) As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

  • Page 4: Operation Panel

    FO-2970MU [2] Operation panel 10 11 12 TEL FAX A.M. FUNCTION VOLUME DOWN RECEPTION SPEED RESOLUTION BROADCAST PAPER TONER LINE MODE DIAL CHECK EMPTY IN USE IN USE REDIAL HOLD/ PQRS WXYZ REDUCTION/ SEARCH COPY/HELP ENLARGEMENT 16/POLL SPEAKER START STOP 17/G1 18/G2 19/G3...

  • Page 5: Chapter 2. Adjustments

    FO-2970MU CHAPTER 2. ADJUSTMENTS [1] Adjustments General Output Voltage limits 4.75V~5.25V Since the following adjustments and settings are provided for this model, make adjustments and/or setup as necessary. +24VH 23.04V~24.96V +24V* 23.04V~24.96V 1. Adjustments Adjustments of output voltage (FACTORY ONLY) Connector CNPW PIN No.
  • Page 6 FO-2970MU DC bias output voltage adjustment VR1 (MC output voltage adjustment volume) Adjust VR2 so that the output voltage is –310V 5V For measurement, use the high voltage tester (effective value me- ter). – DRUM DC-Bias Output voltage check DC-Bias –...
  • Page 7 FO-2970MU 3. IC protectors replacement ICPs (IC Protectors) are installed to protect the TX motor drive circuit CNPRT CNRTH and verification stamp drive circuit. ICPs protect various ICs and elec- CNFUSE tronic circuits from an overcurrent condition. The location of ICPs are shown below: CNLIUA CNPN (1) F100 (ICPS10) is installed in order to protect IC’s from and...

  • Page 8: Diagnostics And Service Soft Switches

    FO-2970MU [2] Diagnostics and service soft switches 1. Operating procedure 1-2. Print diagnosis Two kinds of diagnoses are supported. This diagnosis is concerned with the print which is used for production and service support. 1-1. Fax diagnosis Entering the diagnostic mode This diagnosis is concerned with the main body of fax which is used for production and service support.
  • Page 9 FO-2970MU 2. Diagnostic items description 4) Panel key test This is used to check whether each key is normally operated or not. According to the key input, LCD is displayed. 2-1. Fax diagnosis 1) When the START key is pressed while PANEL KEY TEST is being displayed, a test will start.
  • Page 10 FO-2970MU 9) Auto feeder mode 2-2. Print diagnosis The auto feed function can be checked by inserting and discharging the Rapid key 01: Area print mode document. (After entering this mode, when a document is placed in the The effective printing area frame is printed in the specified sheet size. machine and the START key is pressed, the operation will start.) After this mode is activated, the document size A4(A4 ) and...
  • Page 11 FO-2970MU Rapid key 05: Paper feed aging Rapid key 07: Life all clear The mode is used for aging related to the printing. In this mode, the The mode is used to clear the life counter of the printer of the counter following modes are provided.
  • Page 12 FO-2970MU Rapid key 10: Life clear mode The mode is used to respectively clear the life counter of the printer and the counter of the auto feeder. For setting, proceed with the following procedure. When the life counter clearing mode is selected, the following will be is displayed.
  • Page 13 FO-2970MU 3. How to make soft switch setting To enter the soft switch mode, make the following key entries in sequence. Press FUNCTION START START S F T S W 1 = 0 0 0 0 0 0 0 0 Press FUNCTION key.
  • Page 14 FO-2970MU 4. Soft switch description • Soft switch Switch setting and function Initial DATA ITEM Remarks setting Recall interval Binary input OPTION No. = Set to 01~15 1 (5 x 60 sec = 5 min) Recall times Binary input OPTION No.
  • Page 15 FO-2970MU Switch setting and function Initial DATA ITEM Remarks setting H2 mode MH fixed No (depends on remote machine) Reserved Reserved Modem speed V.17 V. 29 V. 27ter (DCS data reception speed) 14400 12000 9600 7200 9600 7200 4800 2400 No.
  • Page 16 FO-2970MU Switch setting and function Initial DATA ITEM Remarks setting End buzzer 3 sec 1 sec No Beep No Beep OPTION No. 1 No. 2 Communication error treatment No communication error Communication error in RTN sending mode (reception) SW11 CNG transmission after auto dialing Error criterion 10 ~ 20 % 5 ~ 10 %...
  • Page 17 FO-2970MU Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Reserved Reserved SW16 Reserved Reserved Reserved Reserved Speaker volume (3 stages) High High Middle Using No. 1 Volume No. 2 Hand-set receiver volume (3 stages) High High Middle Using No.
  • Page 18 FO-2970MU Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Reserved Reserved SW21 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW22 Reserved Reserved Reserved Reserved Automatic reduce of receive Auto 100% OPTION Cut off mode (COPY mode) Continue Cut-off OPTION...
  • Page 19 FO-2970MU Switch setting and function Initial DATA ITEM Remarks setting Quiet detect time Binary input OPTION No. = 0 (4 sec) SW27 Quiet detect start timing Binary input No. = 1 (5 sec) Reserved Reserved Reserved Reserved SW28 Reserved Reserved Reserved Reserved Reserved...
  • Page 20 FO-2970MU Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Reserved Reserved SW32 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW33 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW34 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW35 Reserved...
  • Page 21 FO-2970MU Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Reserved Reserved SW39 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW40 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW41 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW42 Reserved...
  • Page 22 FO-2970MU Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Reserved Reserved SW46 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW47 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW48 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW49 Reserved...
  • Page 23 FO-2970MU Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Reserved Reserved SW53 Reserved Reserved Reserved Reserved V.34 mode sending speed Sending speed = 2400 (bps) x N Example: 2400 (bps) x 12 = 28800 (bps) 2400 (bps) is set for N = 0. 33600 (bps) is set for N = 15.
  • Page 24 FO-2970MU Switch setting and function Initial DATA ITEM Remarks setting Reserved Reserved Reserved Reserved SW60 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW61 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW62 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved SW63 Reserved...
  • Page 25 FO-2970MU • Soft switch function description SW1 No. 1 ~ No. 4 Recall interval Choice is made for a recall interval for speed, rapid dial numbers, ten key +START and search + START. Use a binary number to program this. If set to 0 accidentally, 1 will be assumed. SW1 No.

  • Page 26: Reserved

    FO-2970MU SW5 No. 2 Date format SW7 No. 5 EOL detect timer Used to select date display/print formats. 25 seconds or 13 seconds are selected for the detection timer of EOL (end of line). This is effective against communication trouble on a spe- 0: DAY-Month-Year cific type of long EOL.

  • Page 27: Example

    FO-2970MU SW10 No. 3, No. 4 CI off detection timer SW11 No. 1, No. 2 End buzzer (Distinctive ring setting off only) The sounding length of the buzzer for normal end of operation set. Set the minimum time period of CI signal interruption which affords to be SW11 No.
  • Page 28 FO-2970MU SW17 No. 1, No. 2 Speaker volume (3 stages) SW19 No. 5, No. 6 Reserved Used to adjust sound volume from a speaker. Set to "0". SW17 No. 3, No. 4 Hand-set receiver volume (3 stages) SW19 No. 7 Reserved Used to adjust sound volume from a handset receiver volume.
  • Page 29 FO-2970MU SW25 No. 1 Busy tone detection ON/OFF time (Shorter duration) SW33 No. 2 Reserved The initial value of detection is set according to electric condition. Set to "1". The set value is changed according to the local switch board. (Errone- SW33 No.
  • Page 30 FO-2970MU SW49 No. 2 ~ No.8 Reserved SW59 No. 5 ~ No. 8 Reserved Set to "0". Set to "0". SW50 No. 1 ~ No.8 Reserved SW60 No. 1, No. 2 Reserved Set to "0". Set to "0". SW51 No. 1 ~ No.8 Reserved SW60 No.

  • Page 31: Troubleshooting

    FO-2970MU [3] Troubleshooting • 1. Fax troubleshooting Apply line equalization SOFT SWITCH 8-1, 2 Refer to the following actions to troubleshoot any of the problems men- May be used in all cases. tioned in 1-4. • Slow down the transmission speed SOFT SWITCH 6-5, 6, 7, 8 [1] A communication error occurs.

  • Page 32: Error Code Table

    FO-2970MU [4] Error code table 1. Communication error code table G3 Transmission Code Final received signal Error Condition (Receiver side) Incomplete signal frame Cannot recognize bit stream after flag NSF, DIS Cannot recognize DCS signal by echo etc. Cannot recognize NSS signal (FIF code etc) Disconnects line during reception (carrier missing etc) Disconnects line by fallback Disconnects line during reception of multi page...
  • Page 33 FO-2970MU Super G3 mode Error Code Transmission Errors Reception Errors E-16 Same as E-0 Same as E-0 E-17 Same as E-1 Same as E-1 E-18 Same as E-2 Same as E-2 E-19 Same as E-8 E-20 Same as E-4 Same as E-9 E-21 Same as E-10 E-22...

  • Page 34: Chapter 4. Diagrams

    FO-2970MU CHAPTER 4. DIAGRAMS [1] Block diagram 4 – 1...

  • Page 35: Wiring Diagram

    FO-2970MU [2] Wiring diagram HANDSET EXT.TEL LINE CNLIUA CNLIUA CN101 THERMISTOR CNPW CNPN CNMT CNMMT CNLSU CNTNR CNPL 4 – 2...

  • Page 36: Point-To-Point Diagram And Connector Signal Name

    FO-2970MU [3] Point- to-point diagram and connector signal name 4 – 3...

  • Page 37: Chapter 5. Circuit Description

    FO-2970MU CHAPTER 5. CIRCUIT DESCRIPTION 3. Operational description Operational descriptions are given below: • [1] Circuit description Transmission operation When a document is loaded in stand-by mode, the state of the docu- ment sensor is sensed via the ASIC (IC15). 1.

  • Page 38: Circuit Description Of Control Pwb

    FO-2970MU [2] Circuit description of control PWB 2) M27C800-90F1 (IC14): pin-42 DIP (ROM) EPROM of 8M bit equipped with software for the main CPU. 1. General description 3) W24010S-70LET (IC1): pin-32 SOP (RAM) Fig. 2 shows the functional blocks of the control PWB, which is com- Line memory for the main CPU system RAM area and coding/decoding posed of 5 blocks.
  • Page 39 FO-2970MU SH7041 (IC5) Terminal descriptions Classification Code Terminal No. Name Function Power 12,26,40, Power Connect Vcc terminals with the power source for all systems. 63,77,85, If any open terminal remained, operation is impossible. 99,112,135 6,14,28, Ground Connect to the ground. 35,42,55, Connect Vss terminals with the ground for all systems.
  • Page 40 FO-2970MU SH7041 (IC5) Terminal descriptions Classification Code Terminal No. Name Function Data bus D0 ~ D15 45,46 Data bus Bilateral data bus for 16 bit (Pin plate QFP-112 ) or 32 bit (Pin plate (QFP-112) 56~60, QFP-144). D0 ~ D31 62,64~70 (QFP-144) 72~76,78...
  • Page 41 FO-2970MU SH7041 (IC5) Terminal descriptions Classification Code Terminal No. Name Function Serial TxD0, 131, Transmitting data Output terminal for transmitting data of SC10 to 1. communication TxD1 (Channels 0 and 1) interface (SCI) RxD0, 130, Receiving data Input terminal for receiving data of SC10 to 1. RxD1 (Channels 0 and 1) SCK0,...
  • Page 42 FO-2970MU (2) Panel control block LR38784A (IC15) Terminal description The following controls are performed by the Gate array (LR38784). Pin No. Signal name • Operation panel key scanning – • – Operation panel LCD display LCPD3 (3) ASIC/Printing control block LCPD4 1) ASIC [LR38784A 208pin (embedded gate array) LCDREQ...
  • Page 43 FO-2970MU LR38784A (IC15) Terminal description Pin No. Signal name Pin No. Signal name DRAK1 DREQ0Z DREQ1Z – – SHCK – – – – RESET2Z USOUT INT1Z – INT2Z – INT3Z – INT4Z – INT5Z OSC3M PEPCKO OSCI PEPCKI WRHZ EXINT1Z WRLZ RESETZ CS2Z...
  • Page 44 FO-2970MU LR38784A (IC15) Terminal description Pin No. Signal name Pin No. Signal name – DOPZ PINZ POUTZ – XBPSTB IO12MR BPBD7 VIDEO – IO12MR BPBD6 IO12MR BPBD5 IO12MR BPBD4 – IO12MR BPBD3 IO12MR BPBD2 IO12MR BPBD1 – – – – –...
  • Page 45 FO-2970MU 2) Printing control (PCU) The CPU and ASIC control printing. 1. Blockdiagram Laser scanning unit Laser start position sensor Motor Main motor driver Laser diode Scanning motor (SH7041) IEEE1284 Host I/F Connector computer ASIC (LR38784A) Heater lamp Driver control circuit Reset circuit Thermistor PIN sensor...
  • Page 46 FO-2970MU c. Electrical connection 3) Unit control In the paper feed and transportation system, drive parts and sensors a. Main motor drive circuit are connected as shown in the figure below. This machine uses the 4-phase pulse motor, and is driven by the follow- ing pulses and the circuit 24VP CONTROL PWB...
  • Page 47 FO-2970MU d. High voltage unit control The high voltage unit outputs the following voltages: • Main charger voltage (DC-950V + AC600V peak to peak) • Transfer charger voltage (DC+2100V + AC600V peak to peak) • Developing bias voltage (DC-390V) The following signals are outputted from the CPU (ASIC) to control the above voltages.
  • Page 48 FO-2970MU f. Laser scanning unit This unit controls the laser beam power and laser beam scanning. The control is performed with the signals inputted outputted to or from the CPU and ASIC. +5VL BD CIRCUIT Q601 A1015 R603 R604 IC602 +24V R601 D601...
  • Page 49 FO-2970MU • Laser control signal 3) Starting operation LEND signal is controlled based on HSYNC signal. Warm-up operation of laser scanning is described below. For simultaneous APC control, SAMP signal is also controlled. The operation is made when the cover is closed from the open state, These timings are made by ASIC.
  • Page 50 FO-2970MU g. Electrical connection CONTROL PWB PRINTER PWB LSU PWB +24V Laser beam detecting PWB ASIC (Start position detecting PWB) (LR38784A) IC603 CNLSU CN601 CN603 CN604 3-terminal +24V +24V +5VL +5VL 136 SAMP regulator SYNC_ SYNC_ 146 VIDEO VIDEO VIDEO SAMP SAMP 135 SYNC-...
  • Page 51 FO-2970MU • After printing, temperature is not controlled. 2) Protect against overheat • Fan motor starts revolving from the beginning of temperature control Though the heater lamp ON signal (HLON) is normal, if triac PD101 and and stops 120 seconds after printing is finished. T2 are kept ON, overheat may result.
  • Page 52 FO-2970MU i. Electrical connection Heater lamp: The 400W halogen lamp is used. This spring presses the pressure roller with a 690g pressure on one side. Thermistor: Thermistor of chip type with good response is used to respond to rapid heating (rapid warm-up of about 8 sec) of the heat roller.
  • Page 53 FO-2970MU j. Timing chart Continuous printing processing *1 Waiting according to fixing temperature (Environmental tempera- • Printing process ture) Pre-revolution processing *2 Top margin Timing from DPAGE (internal signal of ASIC) to BIAS ON (pre-revolu- tion processing) is specified. READY DPAGE Before rotation of printing (unit:sec) VSYNC...
  • Page 54 FO-2970MU k. Top margin control (4) MODEM control block Top margin is set according to the number of lines (the number of HSYNC 1) INTRODUCTION interrupt) from detail paper Pin On to LASER input. Conexant's FM336 modem is a V.34 half-duplex modem. It supports The interval between Pin On and point D is 52.6747 mm.
  • Page 55 FO-2970MU FM336 (IC8) Terminal description Signal Name I/O Type Interface Signal Name I/O Type Interface RESERVED – – RESERVED – – Host interface VSUB – Host interface – Host interface – Host interface – Host interface SLEEP Modem interconnect Host interface VDD1 –...
  • Page 56 FO-2970MU (5) Image signal process block LOCAL ASIC VIDEO SIGNAL LC82103 CLOCK (IC4) VREF+ VREF– Fig. 22 The CIS is driven by the LSI (LC82103), and the output video signal from the CIS in input into the LC82103. The ADC and buffer are provided in the LC82103, and the digital image processing is performed.

  • Page 57: Circuit Description Of Tel/Liu And Hook Sw Pwb

    FO-2970MU [3] Circuit description of TEL/LIU and Hook SW PWB 1. TEL/LIU block operation description (1) Block diagram LIU PWB CONTROL PWB GAIN -C TXOUT SIGTX HS DETECTOR LINE CI DETECTOR EXT. 0:CID RXIN SIXGRX MODEM(FM336) 1:RX TEL MUTE (H:MUTE) 0:MID SPKR TEL IN...
  • Page 58 FO-2970MU 5) Matching transformer [Signals for status recognition according to input signals] The matching transformer performs electrical insulation from the tel- Signal Name Function ephone line and impedance matching for transmitting the TEL/FAX H: The handset is in the on-hook state. signal.

  • Page 59: Circuit Description Of Power Supply Pwb

    FO-2970MU (Example: Fax signal send) LIU PWB CONTROL PWB GAIN -C TXOUT SIGTX HS DETECTOR LINE CI DETECTOR EXT. 0:CID SIXGRX RXIN MODEM(FM336) 1:RX TEL MUTE (H:MUTE) 0:MID SPKR TEL IN 1:HIGH TELOUT SP MUTE (H:MUTE) BZCONT BZCONT IC15 G.A 0:LINE LR38784A 1:BZ...

  • Page 60: Circuit Description Of Cis Unit

    FO-2970MU TRANSFORMER CIRCUIT NOISE RECTIFIED SWITCHING FILTER SMOOTHING CIRCUIT AC IN CIRCUIT CIRCUIT +24V +24VH CIRCUIT +24V SW101 ZERO CROSS CIRCUIT +24VS HEATER CIRCUIT HLON Fig. 25 [5] Circuit description of CIS UNIT This CIS unit picks up optical information from the document, converts it 2.

  • Page 61: Chapter 6. Circuit Schematics And Parts Layout

    FO-2970MU CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT C121 C118 C117 C112 C113 C114 C116 C115 C110 C111 C147 C148 C149 C150 C155 C156 C152 C153 C144 C145 C146 C221 C180 C181 C160 C24 C25 C157 C179 BR23 33 x 4 33 x 4 BR22 33 x 4...
  • Page 62 FO-2970MU C264 100P C361 1000P C261 0.1 C39 0.1 C38 0.1 C40 0.1 C41 0.1 C34 0.1 LCPD0 (4-5I) LCPD0 EXINT1Z TEST1 RTCIO (2-1F) RTCIO RTCCE (2-1F) RTCCE RTCDT (2-1F) RTCDT RTCCK /RAS (1-4B) (2-1F) RTCCK RASZ /B4SNS R250 470 /CASH (9-1E) B4SNS...
  • Page 63 FO-2970MU 6 – 3...
  • Page 64 FO-2970MU 6 – 4...
  • Page 65 FO-2970MU 6 – 5...
  • Page 66 FO-2970MU N.M. 6 – 6...
  • Page 67 FO-2970MU DAP202U C350 6 – 7...
  • Page 68 FO-2970MU C251 C252 C119 6 – 8...
  • Page 69 FO-2970MU C321 C297 C314 C311 C296 N.M. C295 C303 C294 C301 47P C300 1000P C293 C299 4700P C298 4700P C19 N.M. C342 C343 C357 C344 1000P C330 C345 N.M. N.M. C341 C340 C339 C338 C337 C348 C336 C335 C334 C309 C346 C333 C310...
  • Page 70 FO-2970MU Control PWB parts layout (Top side) 6 – 10...
  • Page 71 FO-2970MU Control PWB parts layout (Bottom side) 6 – 11...
  • Page 72 FO-2970MU 6 – 12...
  • Page 73 FO-2970MU TEL/LIU and Hook SW PWB parts layout (Top side) 6 – 13...
  • Page 74 FO-2970MU TEL/LIU and Hook SW PWB parts layout (Bottom side) 6 – 14...
  • Page 75 FO-2970MU 0.56(1W) SENSE2 0.56(1W) SENSE1 OUT4 OUT3 OUT2 OUT1 C12 1000P C8 1000P 330P 330P 3.0(1/2W) RD2.4ES DSM1D DSM1D 0.015(F) 1000P 4700P(F) 1000P/3KV 1000P/6KV 100M RK(1/2W) 8.2M RK(1/2) 1000P/1KV 1000P/6KV 6 – 15...
  • Page 76 FO-2970MU 390P 390P 390P 6 – 16...
  • Page 77 FO-2970MU Printer PWB parts layout 6 – 17...
  • Page 78 FO-2970MU R505 (OPTION) (OPTION) R507 (OPTION) R101 (OPTION) 6 – 18...
  • Page 79 FO-2970MU Power supply PWB parts layout 6 – 19...
  • Page 80 FO-2970MU 6 – 20...
  • Page 81 FO-2970MU PARTS GUIDE FO-2970M MODEL SELECTION CODE DESTINATION U.S.A. CONTENTS Cabinet, etc. Fusing unit Operation panel unit Packing material & Accessories Document guide upper unit Control PWB unit Drive unit TEL/LIU and Hook SW PWB unit Scanner frame unit Printer PWB unit...

  • Page 82: Cabinet, Etc

    FO-2970MU [1] Cabinet, etc. Scanner frame unit Operation panel unit Printer unit Document guide upper unit – 1 –...
  • Page 83 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [1] Cabinet,etc. CCNW-270ASC01 Speaker ass’y GDAI-2074XHZZ Handset holder upper GDAI-2075XHZZ Handset holder lower DCEKC182PSCZZ Control PWB unit DCEKL259CSC01 TEL/LIU and Hook SW PWB unit MLEVP2332SCZZ Hook switch lever GCABA2350SCZA Upper cabinet GCABB2351SCZA Document guide lower GCABC2352SCZA...

  • Page 84: Operation Panel Unit

    FO-2970MU [2] Operation panel unit [3] Document guide upper unit 5 17 – 3 –...
  • Page 85 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [2] Operation panel unit DCEKP223CSC01 Operation panel PWB unit(without sensor) GCASP2121SCZG Panel case JBTN-2282SCZA 10 key JBTN-2283SCZA Direct key JBTN-2284SCZZ Start key JBTN-2285SCZA Copy,reduction key JBTN-2286SCZA Stop key JBTN-2287SCZZ E-mail key JBTN-2288SCZA Function key QCNW-268ASCZZ...

  • Page 86: Drive Unit

    FO-2970MU [4] Drive unit [5] Scanner frame unit Drive unit – 5 –...
  • Page 87 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [4] Drive unit LPLTM3091SCZZ Radiator plate LPLTP3094SCZZ Drive frame NGERH2277XHZZ Reduction gear B NGERH2279XHZZ Idler gear NGERH2380XHZZ Reduction gear(17/36Z) NGERH2395AXZZ Gear,White(15/23Z) PSHEZ3528SCZZ Motor sheet RMOTZ2150SCZZ Transfer motor QCNW-342ASCZZ Ground cable C XEBSE30P08000 Screw(3x8) [5] Scanner frame unit...

  • Page 88: Printer Frame

    FO-2970MU [6] Printer frame Upper frame Lower frame Fusing unit – 7 –...
  • Page 89 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [6] Printer frame JKNBZ0004GCZZ Fusing knob LPLTM0159GCZ1 Gear plate LPLTM0282GCZ2 Heat sink plate MLEVP0037GCZZ Fusing clutch lever MLEVP0093GCZZ Tray lock lever MSPRC0135GCAZ Fusing clutch spring MSPRC3151SCZZ SW lever spring MSPRT0307GCZZ Lock lever spring NBLTH0008GCA1 Fan belt NBRGP0106GCZZ...
  • Page 90 FO-2970MU [7] Upper frame – 9 –...
  • Page 91 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [7] Upper frame DHAI-0139GCZZ MM harness LBOSZ0058GCZ1 Paper feed roller boss LFIX-0003GCZZ DV fixer LPLTM0273GCZZ MM heat sink PMLT-0124GCZZ FFC protect molt RCORF7013XCZZ Core RMOTN0039GCZZ Main motor RPLU-0004GCZZ Paper feed solenoid MLEVP0046GCZZ Sleeve release lever MLEVP0088GCZZ...
  • Page 92 FO-2970MU [8] Lower frame – 11 –...
  • Page 93 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [8] Lower frame CPLTP0274PS51 Separate plate ass’y DUNTK0152PSZZ DV bias LFRM-0045GCZ1 Lower frame LPLTM0163GCZZ Separation electrode LPLTM0275GCZ1 Lift plate QSLP-0028GCZZ Earth terminal MLEVP0038GCZZ DR lock lever R MLEVP0039GCZZ DR lock lever L MLEVP0040GCZZ PIN actuator MLEVP0089GCZZ...
  • Page 94 FO-2970MU [9] Fusing unit PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [9] Fusing unit CHLDZ0040PS73 Temperature fuse holder QSLP-0030GCZZ Fusing AC terminal C RDTCT0014GCZZ Thermistor MSPRT0308GCZZ Fusing separate spring RLMPU0021GCZZ Heater lamp NBRGC0035GCZ1 Fusing bearing R NBRGP0082GCZZ Fusing bearing L NGERH0083GCZZ Fusing gear(27T) NGERH0174GCZZ...

  • Page 95: Packing Material & Accessories

    CPLTP3088SC02 Received document tray ass’y DUNTK369BSCOG Handset unit CPLTP3085SC02 Paper tray ass’y DUNT-205CSCZA Toner cartridge(Initial starter cartridge) TLABM311BSCZA Rapid key labels UDSKA2024SCZA Sharp laser multifunction CD-ROM QCNW-289ASCOG Handset cord QCNW-290ASCZZ Telephone line cord SPAKA315BSCZZ Add.,left SPAKA316BSCZZ Add.,right SPAKA317BSCZZ Add. SPAKC229CSCCZ...

  • Page 96: Control Pwb Unit

    FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [11] Control PWB unit UBATL2049SCZZ Battery(CR2032T23) [BAT] RR-DZ1115AFZZ Resistor array(10K x4) [BR1] RR-DZ1115AFZZ Resistor array(10K x4) [BR2] RR-DZ1115AFZZ Resistor array(10K x4) [BR3] RR-DZ1115AFZZ Resistor array(10K x4) [BR4] RR-TZ3016SCZZ Resistor array(33 x4) [BR5] RR-TZ3016SCZZ Resistor array(33 x4)
  • Page 97 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [11] Control PWB unit VCCCCY1HH180J Capacitor(50WV 18PF) [C114] VCCCCY1HH180J Capacitor(50WV 18PF) [C115] VCCCCY1HH180J Capacitor(50WV 18PF) [C116] VCCCCY1HH180J Capacitor(50WV 18PF) [C117] VCCCCY1HH180J Capacitor(50WV 18PF) [C118] VCCCCY1HH180J Capacitor(50WV 18PF) [C120] VCCCCY1HH180J Capacitor(50WV 18PF) [C121] VCKYCY1HB222K Capacitor(50WV 2200PF)
  • Page 98 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [11] Control PWB unit VCKYCY1HB102K Capacitor(50WV 1000PF) [C243] VCKYCY1HB102K Capacitor(50WV 1000PF) [C244] VCKYCY1HB102K Capacitor(50WV 1000PF) [C247] VCCCCY1HH470J Capacitor(50WV 47PF) [C249] VCKYCY1EF104Z Capacitor(25WV 0.1 F) [C250] VCKYCY1EF104Z Capacitor(25WV 0.1 F) [C253] VCKYCY1EF104Z Capacitor(25WV 0.1 F) [C254] VCKYCY1HB102K...
  • Page 99 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [11] Control PWB unit VCKYCY1AF105Z Capacitor(10WV 1 F) [C411] RC-KZ0001RCZZ Ceramic capacitor array(100PFx4) [CA1] RC-KZ0001RCZZ Ceramic capacitor array(100PFx4) [CA2] RC-KZ0001RCZZ Ceramic capacitor array(100PFx4) [CA3] RC-KZ0001RCZZ Ceramic capacitor array(100PFx4) [CA4] QCNCM7014SC0G Connector(7pin) [CNCIS] QCNCM7014SC0C Connector(3pin)
  • Page 100 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [11] Control PWB unit VRS-CY1JB271J Resistor(1/10W 270 [R162] VRS-CY1JB103J Resistor(1/10W 10K [R163] VRS-CY1JB330J Resistor(1/10W 33 [R164] VRS-CY1JB101J Resistor(1/10W 100 [R165] VRS-CY1JB680J Resistor(1/10W 68 [R166] VRS-CY1JB271J Resistor(1/10W 270 [R168] VRS-CY1JB101J Resistor(1/10W 100 [R169] VRS-CY1JB101J Resistor(1/10W 100...
  • Page 101 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [11] Control PWB unit VRS-CY1JB103J Resistor(1/10W 10K [R270] VRS-CY1JB470J Resistor(1/10W 47 [R271] VRS-CY1JB470J Resistor(1/10W 47 [R272] VRS-CY1JB470J Resistor(1/10W 47 [R273] VRS-CY1JB470J Resistor(1/10W 47 [R274] VRS-CY1JB470J Resistor(1/10W 47 [R275] VRS-CY1JB470J Resistor(1/10W 47 [R276] VRS-CY1JB470J Resistor(1/10W 47...

  • Page 102: Tel/Liu And Hook Sw Pwb Unit

    FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [11] Control PWB unit VRS-CY1JB000J Resistor(1/10W 0 [R358] VRS-CY1JB000J Resistor(1/10W 0 [R359] VRS-CY1JB103J Resistor(1/10W 10K [R364] VRS-CY1JB103J Resistor(1/10W 10K [R365] VRS-CY1JB103J Resistor(1/10W 10K [R366] VRS-CY1JB000J Resistor(1/10W 0 [R368] VRS-CY1JB000J Resistor(1/10W 0 [R369] VRS-CY1JB271J Resistor(1/10W 270...

  • Page 103: Printer Pwb Unit

    FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [12] TEL/LIU and Hook SW PWB unit VHDDSS133//-1 Diode(1SS270) [D1] VHDDSS133//-1 Diode(1SS270) [D2] VHD0R5G4B42-1 Diode bridge(0R5G4B42) [DB1] VHINJM2904D-1 IC,OPE AMP.(NJM2904D) [IC1] RCILZ2118SCZZ Coil [L1] RFILN2027XHZZ Coil(R-5C) [L2] RFILN2027XHZZ Coil(R-5C) [L3] RFILN2027XHZZ Coil(R-5C) [L4] RFILN2027XHZZ...
  • Page 104 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [13] Printer PWB unit VCKYPA1HB391K Capacitor(50WV 390PF) [C18] VCQYNA1HM472K Capacitor(50WV 4700PF) [C19] VCQYNA1HM153K Capacitor(50WV 0.015 F) [C20] VCKYPA1HB102K Capacitor(50WV 1000PF) [C21] VCKYPA1HB102K Capacitor(50WV 1000PF) [C22] VCTYPA1HF104Z Capacitor(50WV 0.1 F) [C23] VCTYPA1HF104Z Capacitor(50WV 0.1 F) [C24] VCEAGA1VW476M...

  • Page 105: Power Supply Pwb Unit

    FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [13] Printer PWB unit VRD-HT2EY103J Resistor(1/4W 10K [R17] VRD-HT2EY203J Resistor(1/4W 20K [R18] VRD-HT2EY203J Resistor(1/4W 20K [R19] VRD-HT2EY103J Resistor(1/4W 10K [R20] VRD-HT2EY122J Resistor(1/4W 1.2K [R21] VRD-HT2EY122J Resistor(1/4W 1.2K [R22] VRD-HT2EY122J Resistor(1/4W 1.2K [R23] VRD-HT2EY122J Resistor(1/4W 1.2K...
  • Page 106 FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [14] Power supply PWB unit 0KY0K207B0020 Connector [CN1] 0KY0K251A0020 Connector(B2P3-VH) [CN2] 0KY0K214L0120 Connector [CN101] 0KY0D251A0020 Diode(1SS133) [D4] 0KY0D466A0600 Zener diode(HZS9B) [D5] 0KY0D251A0020 Diode(1SS133) [D6] 0KY0D251A0020 Diode(1SS133) [D7] 0KY0D157A0060 Diode(ERA15-06) [D10] 0KY0D157A0060 Diode(ERA15-06) [D11] 0KY0D157A0060...

  • Page 107: Operation Panel Pwb Unit

    FO-2970MU PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [14] Power supply PWB unit (Unit) RDENT2148SCZZ Power supply PWB unit [15] Operation panel PWB unit QSW-K0005AWZZ Tact switch [SW] QSW-Z2262AXZZ FR sensor switch [FR SNS] QSW-M2294XHZZ ORG sensor switch [ORG SNS] (Unit) DCEKP223CSC01 Operation panel PWB unit(without sensor)
  • Page 108 FO-2970MU I n d e x PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK RANK MARK RANK LX-WZ0017GCZZ 7-W1 NGERH2395AXZZ CCASP2121SC08 2-901 LX-WZ0018GCZZ 7-W2 NGERP2318XHZZ 1-31 CCNW-270ASC01 LX-WZ0019GCZZ 7-W3 NROLM0108GCZ1 9-10 CFRM-2214SC51 7-23...
  • Page 109 FO-2970MU PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE MARK MARK MARK RANK RANK RANK RANK RANK RANK RR-TZ3012SC10 11-15 VCCCCY1HH331J 11-116 QCNW-289ASCOG 10-8 QCNW-290ASCZZ 10-9 RR-TZ3016SCZZ 11-6 11-154 QCNW-342ASCZZ 1-29 11-7 VCCCCY1HH470J 11-164 11-8 11-184 11-9 11-188 QCNW-343ASCZZ...
  • Page 110 FO-2970MU PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK RANK MARK RANK VCKYCY1HB102K 12-15 VHDDSM1D1//-1 13-55 VCKYCY1EF104Z 11-56 11-57 12-20 13-58 11-58 12-21 VHDDSS133//-1 12-29 11-59 VCKYCY1HB103K 11-75 12-30 11-76 13-64 11-60 11-61...
  • Page 111 FO-2970MU PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE MARK MARK MARK RANK RANK RANK RANK RANK RANK VRS-CY1JB101J 11-301 VRS-CY1JB152J 11-315 VRD-HT2EY122J 13-92 13-102 11-308 12-68 13-103 11-309 12-69 13-104 11-310 VRS-CY1JB154J 11-378 11-319 VRS-CY1JB163J 12-62 13-105 13-106...
  • Page 112 FO-2970MU PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK RANK MARK RANK XEBSD30P30000 8-B3 0KY0R153U2200 14-69 VRS-CY1JB471J 11-368 11-369 XEBSE30P08000 1-B3 0KY0R153U2230 14-71 11-382 4-B1 14-72 11-384 XEBSF30P12000 1-B4 0KY0R153U2730 14-73 XEPSD30P06X00 9-B5...
  • Page 113 FO-2970MU CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer.
  • Page 114 FO-2970MU © COPYRIGHT 2000 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Table of Contents