Sharp FO-2970M Service Manual page 10

FO-2970MU
9) Auto feeder mode
The auto feed function can be checked by inserting and discharging the
document. (After entering this mode, when a document is placed in the
machine and the START key is pressed, the operation will start.)
After this mode is activated, the document size A4(A4
sensor information A4(A4 ORG) are displayed when the document
sensor is turned.
AUTO FEEDER MODE
(
After setup of the document
AUTO FEEDER MODE
A4 (A4 ORG)
Only the sensor which is
activated (fallen down) is displayed.)
The paper sheet size (A4) is
displayed.
10) Motor aging mode
Regardless of the presence or absence of a document, the transmis-
sion system motor will continue to run until the STOP key is pressed.
When the START key is pressed after this mode has been selected, the
motor will run at the STANDARD mode speed. Then, when the image
quality is changed using the RESOLUTION key, the motor will run at the
speed used for that image quality.
(When HALF-TONE is selected, the motor will run at the FINE
modespeed.)
11) TEL. number set
The function is used to simplify the registration of FAX/TEL No. during
aging.
1
The diagnosis mode is activated. If anything is not registered in the
Rapid number 01 or any program or group is registered, it will pass
the diagnosis without doing anything.
2
The FAX number (including the substitutive destination) of the Rapid
number 01 is copied to the Rapid numbers 02 thru 19.
3
FAX number of the Rapid number 01 is copied to SPEED key num-
bers 00 thru 99.
4
If any chain dial is not set in the Rapid number 01, the Rapid num-
bers 01 thru 19 and SPEED key numbers 00 thru 10 are registered in
the group number 04.
If any chain dial is set, the group will be not produced but the chain
dial setting alone of the Rapid number 01 will be reset.
(In all others except the Rapid number 01, the chain dials will be
continuously set as they are.)
Rapid key
RXX
SPEED key SXX
(12th and subsequential letters of the destination name registered in the
Rapid number 01 will be discarded.)
12) Signal Send Mode 2
The signals concerned with V.34 & V.8 are checked.
After this mode is activated, press the START key, and the signals will
be sent in the following sequence.
It can be used to check the modem.
[ 1] No signals (CML-ON) [10] 14400bps (V.34)
[ 2] 33600bps (V.34) [11] 12000bps (V.34)
[ 3] 31200bps (V.34) [12] 9600bps (V.34)
[ 4] 28800bps (V.34) [13] 7200bps (V.34)
[ 5] 26400bps (V.34) [14] 4800bps (V.34)
[ 6] 24000bps (V.34) [15] 2400bps (V.34)
[ 7] 21600bps (V.34) [16] 0-300bps (V.21)
[ 8] 19200bps (V.34) [17] ANsam (V.8)
[ 9] 16800bps (V.34) [18] END
)
XX : Rapid number
XX : Speed key number
2-2. Print diagnosis
Rapid key 01: Area print mode
The effective printing area frame is printed in the specified sheet size.
) and
1
2
3
4
5
6
7
8
9
4mm
1. [Full black pattern]
2. [Intermediate tone 2 pattern]
3. [Intermediate tone 1 pattern]
4. [Mesh point pattern]
5. [Longitudinal strip 2 pattern]
Black 2 dot and white 2 dot are repeated in line.
6. [Lateral strip 2 pattern]
Black 2 line and white 2 line are repeated.
7. [Longitudinal strip 1 pattern]
Black 1 dot and white 1 dot are repeated in line.
8. [Lateral strip 1 pattern]
Black 1 line and white 1 line are repeated.
9. [Full White pattern]
Rapid key 02: Check pattern 1
The lateral stripe 2 pattern is printed on one sheet.
(Black 2 line and white 2 line are repeated.)
Rapid key 03: Check pattern 2
The lateral stripe 2 pattern is printed on multiple pages.
Press the STOP key to end the printing.
Rapid key 04: Check pattern 3
The intermediate tone 1 is printed on one sheet.
2 – 6
4mm
4mm
208mm
4mm
The left pattern is repeated.
The left pattern is repeated.
The left pattern is repeated.