Alliance Laundry Systems CABINET HARDMOUNT HC80VNV Programming Manual
Cabinet hardmount-opl v series microcomputer 2 speed and variable speed
Hide thumbs
Also See for CABINET HARDMOUNT HC80VNV:
- Installation manual (112 pages) ,
- Operation & maintenance manual (46 pages) ,
- Troubleshooting manual (110 pages)
Table of Contents
Advertisement
Washer-Extractors
Cabinet Hardmount – OPL
V-Series Microcomputer
2 Speed and Variable-Speed
Refer to Page 3 for Model Identification
CHM166C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F232141R3
www.comlaundry.com
December 2008
Advertisement
Table of Contents
Related Manuals for Alliance Laundry Systems CABINET HARDMOUNT HC80VNV
Summary of Contents for Alliance Laundry Systems CABINET HARDMOUNT HC80VNV
- Page 1 Washer-Extractors Cabinet Hardmount – OPL V-Series Microcomputer 2 Speed and Variable-Speed Refer to Page 3 for Model Identification CHM166C Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. F232141R3 www.comlaundry.com December 2008...
- Page 3 All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. F232141 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction... Model Identification ...
-
Page 4: Model Identification
Model Identification Information in this manual is applicable to these models: HC80VNV SC125VNV SC18VN2 SC20VN2 SC27VN2 SC30VN2 SC35VN2 SC35VNV © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction SC40VN2 UC125VNV SC40VNV UC18VN2 SC50VN2 UC20VN2 SC50VNV UC27VN2 SC60VN2... -
Page 5: Nameplate Location
Nameplate F232141 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Replacement Parts If literature or replacement parts are required, contact the source from which the machine was purchased or... -
Page 6: Safety Information
NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information Important Safety Instructions To reduce the risk of fire, electric shock,... - Page 7 If this occurs, have washer checked by a qualified service person. F232141 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 20. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
-
Page 8: Safety Decals
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Be careful around the open door, particularly when loading from a level below the door. Impact with door edges can cause personal injury. -
Page 9: Operator Safety
Machine is not connected to a properly grounded circuit. F232141 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Do not bypass any safety devices in the machine. Never operate the machine with a bypassed or disconnected balance system. -
Page 10: Entering Program Mode
Figure 1 4. Flip switch to down position to enter PROGRAM Mode. Display will show temperature of sump. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming Procedures for Calibration of Temperature Probe for V-Computer Controlled Machines 1. - Page 11 (refer to Figure 2). F232141 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT SW012 12. When the temperatures match, calibration is completed.
-
Page 12: Programming Setup Options
4. Press the Stop (*) key anytime to exit SETUP Mode. The display will show sump temperature. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Programming a Cycle 1. With the display showing sump temperature, press the Up (arrow) key to edit a cycle. -
Page 13: Programming Cycle Segments
Low (“Lo”), Medium (“nEd”) or High (“HI”). Press Start (#) key. F232141 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 11. Use Up or Down (arrow) key to select Supply Option. Refer to Table 4. Display... -
Page 14: Test Cycle
17. Press the Stop (*) key to complete the cycle programming procedure. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Test Cycle To select test cycle: 1. Flip program switch to up position (RUN Mode). -
Page 15: Cycle Charts
Time (Min.) Water Both (warm) Level Supply Temp (F) Drain DrAI Spin (Sec.) F232141 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT V-Computer Standard OPL Cycles Permanent Cotton Permanent Press Terrycloth Press Medium Soil Medium Soil... - Page 16 Time (Min.) Water Both (warm) Level Supply Temp (F) Drain DrAI Spin SPn3 Spin (Min.) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Permanent Cotton Permanent Press Terrycloth Press Medium Soil Medium Soil Heavy Soil Both (warm)
- Page 17 Both (warm) Level High High Supply Temp (F) Drain DrAI DrAI Spin (Sec.) F232141 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Rags Reclaim Personals with Bleach Heavy Soil AG 1 AG 1 AG 1 AGSn AGSn...
- Page 18 Spin (Sec.) Fill 9 Time (Min.) Water Level Supply Temp (F) Drain Spin Spin (Min.) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Rags Reclaim Personals with Bleach Heavy Soil Both (warm) Both (warm) High High...
- Page 19 Cold Cold Level Medium Medium Supply Temp (C) Drain DrAI DrAI Spin (Sec.) F232141 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Normal Normal Normal Permanent 60ºC 60ºC 40ºC Press 90ºC (PreWash) (PreWash) AG 1 AG 1...
- Page 20 Time (Min.) Water Cold Cold Level Medium Medium Supply Temp (C) Spin SPn3 SPn3 Spin (Min.) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Normal Normal Normal Permanent 60ºC 60ºC 40ºC Press 90ºC (PreWash) (PreWash) Cold Cold...
Need help?
Do you have a question about the CABINET HARDMOUNT HC80VNV and is the answer not in the manual?
Questions and answers