Alliance Laundry Systems CHM1772C Installation Manual
  1. Manuals
  2. Brands
  3. Alliance Laundry Systems Manuals
  4. Washer
  5. CHM1772C
  6. Installation manual

Alliance Laundry Systems CHM1772C Installation Manual

Washer-extractors cabinet hardmount
Hide thumbs Also See for CHM1772C:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operation & Maintenance Manual, Installation Manual
Washer-Extractors
Cabinet Hardmount
Refer to Page 6 for Model Identification
CHM1772C
CHM1772C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F8208301R5
www.comlaundry.com
February 2011

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CHM1772C and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Alliance Laundry Systems CHM1772C

Summary of Contents for Alliance Laundry Systems CHM1772C

  • Page 1 Washer-Extractors Cabinet Hardmount Refer to Page 6 for Model Identification CHM1772C CHM1772C Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. F8208301R5 www.comlaundry.com February 2011...

  • Page 3: Table Of Contents

    All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. F8208301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 4: Safety Information

    8. Do not reach into the washer if the wash drum is moving. 9. Do not install or store the washer where it will be exposed to water and/or weather. 10. Do not tamper with the controls. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 5 22. Loading door MUST BE CLOSED any time the washer is to fill, tumble or spin. DO NOT bypass the loading door switch by permitting the washer to operate with the loading door open. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 6: Safety Decals

    If questions regarding safety arise, contact the manufacturer immediately. Use manufacturer-authorized spare parts to avoid safety hazards. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 7: Operator Safety

    The door does not remain securely locked during the entire cycle. b. Excessively high water level is evident. c. Machine is not connected to a properly grounded circuit. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 8: Introduction

    SCU020JDV UCU020GN2 HCN020HNF HCU020HX2 SCN020GX2 SCN020WC2 SCU020JE2 UCU020HN2 HCN020HY2 HCU020KCF SCN020GY2 SCN020WCF SCU020JEF UCU020HNF HCN020HYF HCU020KCV SCN020HN2 SCN020WCV SCU020JEV UCU020KN2 HCN020KC2 HCU020KE2 SCN020HNF SCN020WD2 SCU020JL2 UCZ020GN2 (Continued) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 9 SCN040WCV SCU040JLV UCU040HNF HCN040KD2 SCD040GD2 SCN040HNF SCN040WDV SCU040JX2 UCU040KN2 HCN040KDF SCD040LD2 SCN040JC2 SCN040WY2 SCU040JXF UCU040KNV HCN040KDV SCL040GC2 SCN040JCF SCN040WYF SCU040JXV VCU040GN2 HCN040KEF SCL040GN2 SCN040JCV SCN040WYV SCU040JY2 (Continued) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 10 HCU080GXF SCN080GNF SCN080WYV SCU080JLF UCU080KNV HCN080HYF HCU080GYF SCN080GXF SCU080GCF SCU080JLV VCU080GNF HCN080HYV HCU080HCF SCN080GYF SCU080GDF SCU080JYF HCN080KCF HCU080HNF SCN080HNF SCU080GEF SCU080JYV SCL125KNV UCU125KNV SCN125KNV SCN125LYV SCU125KNV UCL125KNV © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 11: Delivery Inspection

    If any damage is discovered upon removal of the crate and/or protective cover, advise the carrier and file a written claim immediately. CHM2233N Nameplate Figure 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 12 Max. Load : LB LB Schematic : Schematic : 30 - 85 psi, 2 - 5.7 Supply Water: Supply Water: EXAMPLE OF NAMEPLATE CHM2286N CHM2286N Figure 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 13: Replacement Parts

    Customer Service For technical assistance, contact your local distributor or call: Alliance Laundry Systems (920) 748-3121 Ripon, Wisconsin U.S.A. Alliance International +32 56 41 20 54 Wevelgem, Belgium © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 14: Specifications And Dimensions

    Cylinder volume, ft. 2.76 4.19 6.34 9.00 (78.1) (118.6) (180) (255) Perforation size, in. (mm) 0.188 0.188 0.188 0.188 (4.76) (4.76) (4.76) (4.76) Perforation open area, % 17.5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 15 (1.3) (2.01) Cylinder Speeds Wash/reverse speed, RPM High extract speed, RPM Centrifugal Force Data Wash/reverse centrifugal force, G High extract centrifugal force, G 80.3 72.1 78.1 85.4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 16 200V 10.8 10.8 240V 15.6 15.6 380V 13.0 13.0 415V 15.5 15.5 480V 10.4 10.4 15.6 15.6 Electrical heating elements Electrical heat element size, kW © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 17 1200 (101) (113) (129) (189) (239) (302) Drive Train Information Number of motors in drive train Drive motor power, hp (kW) (.75) (.75) (1.7) (2.2) (3.7) (5.6) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 18 15.6 15.6 31.2 380V 13.0 13.0 19.6 34.4 415V 15.5 15.5 23.3 480V 10.4 10.4 15.6 15.6 31.2 54.8 Electrical heating elements Electrical heat element size, kW © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 19 20, 30, 40, 60 and 80 POUND CAPACITY MACHINES CHM2278N Supply Dispenser Cold Water Inlet Input Power Block Compartment Vacuum Breaker Hot Water Inlet Drain Outlet Figure 3 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 20 (1142 mm) (1199 mm) (1267 mm) (1426 mm) 9 in. 9 in. 9 in. 9 in. 9 in. (229 mm) (229 mm) (229 mm) (229 mm) (229 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 21 51.26 in. (1302 mm) 60 in. (1524 mm) 75.15 in. (1909 mm) 9.92 in (252 mm) 83.4 in. (2118 mm) 88.09 in. (2237 mm) 2.86 in. (73 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 22 39.28 in. (998 mm) 48 in. (1219 mm) 60.21 in. (1529 mm) 7.94 in (202 mm) 65.77 in. (1671 mm) 70.47 in. (1790 mm) 2.29 in. (58 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 23: Dimensional Clearances

    (914 mm) 12 in. 12 in. 12 in. 12 in. 18 in. 24 in. Minimum (305 mm) (305 mm) (305 mm) (305 mm) (457 mm) (610 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 24: Installation

    * Recommend SAE 495 Grade 5 or higher strength bolts. Table 1 WARNING To reduce the risk of fire, this appliance must be bolted to an uncovered concrete floor. W731 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 25 (kN-m) (1.38) (2.08) (3.05) (4.51) (11.5) (19.7) Maximum vertical load, lbs. (kN) 1313 1824 2394 4799 6904 (4.23) (5.84) (8.11) (10.65) (21.35) (30.7) Table 3 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 26: Concrete Foundation Installation

    (2 and F-Speed Models) .5 in. (13 mm) minimum 6 in. (152 mm) minimum (V-Speed Models) 4 in. (102 mm) minimum Concrete reinforcing bar Figure 6 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 27 (38 mm) to extend above the surface of the concrete. Refer to the Machine Anchoring section. 7. Allow concrete to dry and cure before machine is placed into service. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 28 COMPACTED FILL DIRT 24 in. (609 mm) DEPTH CHM2283N 125 MODELS CHM2283N 12 in. (305 mm) 48 in. (1219 mm) 6 in. (152 mm) 6 ft. (1829 mm) Figure 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 29: Machine Anchoring

    12. Fill the space between the machine base and the floor with a good quality non-shrinking machinery grout to ensure a stable installation. Grout completely under all frame members. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 30: Elevated Base Frame Installation

    .38 inch floor. (9.5 mm) in 20, 30 and 60 pound models and .25 inch (6.3 mm) in 40 pound models. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 31 Refer to Table 4. P035I Machine Base Mounting Bolt Threads Grouting Bolt-Locator Fixture or Rebar Frame Figure 12 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 32: Mounting Bolt Hole Locations (Without Elevated Base Frames)

    20.88 in. (530 mm) Front of Front Panel 2.56 in. 2.56 in. 20 Models (65 mm) (65 mm) CHM2224N Figure 13 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 33 23.88 in. (607 mm) Front of Front Panel 30 Models 2.56 in. 2.56 in. (65 mm) (65 mm) CHM2063N Figure 14 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 34 (45 mm) (660 mm) Front of Front Panel 30.63 in. 2.32 in. (778 mm) (59 mm) 40 Models CHM206 CHM2067N Figure 15 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 35 (760 mm) (32 mm) Front of Front Panel 2.03 in. (52 mm) 2.03 in. 60 Models (52 mm) CHM2065N Figure 16 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 36 (1054 mm) 80 Models* CHM2334 CHM2334N *For close mounting, use mounting bolt pattern labeled “A”; for standard mounting, use “B.” Figure 17 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 37 (591 mm) (591 mm) Front of Front Panel 0.75 in. (19 mm) 48 in. (1219 mm) 125 Models CHM2069N Figure 18 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 38: Mounting Bolt Hole Locations (With Elevated Base Frames)

    20.88 in. (530 mm) Front of Front Panel 2.75 in. 2.75 in. (70 mm) (70 mm) 20 Models CHM2070N Figure 19 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 39 23.88 in. (607 mm) Front of Front Panel 2.75 in. 2.75 in. (70 mm) (70 mm) 30 Models CHM2072N Figure 20 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 40 2.38 in. Front of Front Panel (61 mm) 30.88 in. (784 mm) 2.44 in. 40 Models (62 mm) CHM2074N Figure 21 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 41 30 in. (762 mm) Front of Front Panel 2.22 in. 2.22 in. (56 mm) (56 mm) 60 Models CHN2076N CHM2076N Figure 22 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 42: Drain Connection

    Overflow Hose Drain Valve Vent Pipe* Drain Tee Trap (as required by local codes) * Drain line must be vented to meet local plumbing codes. Figure 24 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 43 6 in. (152 mm) 4 in. (102 mm) 6 in. (152 mm) 6 in. (152 mm) 8 in. (203 mm) 8 in. (203 mm) 80, 125 Table 6 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 44: Water Connection Requirements

    2 in. (50 mm) 2 in. (50 mm) 2.5 in. (70 mm) 2 in. (50 mm) Table 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 45: Electrical Installation Requirements

    IMPORTANT: Alliance Laundry Systems warranty does not cover components that fail as a result of improper input voltage. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 46: Input Power Conditioning

    The stinger leg should be connected to the center Phase B on the reactor. Table 9 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 47: Input Voltage Requirements

    15 in this section for model-specific circuit breaker requirements. IMPORTANT: All quick disconnects should comply with the above specifications. DO NOT use fuses instead of circuit breakers. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 48: Phase Adder

    Customer Input Power Terminals Figure 28 Machines can be converted for lower voltage operation and/or 50 Hz operation. Refer to conversion label by serial plate for details. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 49 (starting 7/7/10) 380 – 415 (starting 7/7/10) 200 – 240 50/60 NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. Table 10 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 50 7/7/10) 380 – 415 50/60 (starting 7/7/10) 200 – 240 50/60 NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. Table 11 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 51 7/7/10) 200 – 240 50/60 10.0 200 – 240 50/60 10/6 NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. Table 12 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 52 380 – 415 (starting 7/7/10) 200-240 50/60 10.0 200-240 50/60 11/8 NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. Table 13 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 53 7/7/10) 25.0 380 – 415 (starting 7/7/10) 200 – 240 50/60 NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. Table 15 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 54: Steam Requirements (Steam Heat Option Only)

    Loops do not prevent drips if these instructions are not followed. IMPORTANT: Failure to follow these instructions could damage the machine and void the warranty. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 55: External Supplies

    “RELAY COM” and the other to the external “RELAY COM”. Do not use the transformer dispenser input signals common. terminals if an external power supply is used. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 56: Connection Of External Liquid Supplies

    Consult the supply vendor instructions for operational CHM2001N details about supply injections. Strain Relief for Liquid Chemical Supply Lines Supply Dispenser Lid Four Way Water Valve Dry Supply Cups Supply Dispenser Figure 30 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 57: Start Up

    3. For V-speed models, have a qualified electrician reverse any two motor leads at the AC terminal block. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

This manual is also suitable for:

Hcd020gd2Hcd020jd2Hcd020ld2Hcl020gd2Hcl020gn2Hcl020hdf ... Show all

Table of Contents