Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Alliance Laundry Systems Hardmount Coin and OPL
Summary of Contents for Alliance Laundry Systems Hardmount Coin and OPL
- Page 1 Washer-Extractors Cabinet Hardmount Mechanical Timer Coin and OPL Models Refer to page 6 for Model Identification CHM166C Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. F232134R5 www.comlaundry.com June 2008...
-
Page 3: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. F232134 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Table of Contents... Safety Information... -
Page 4: Safety Information
NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information Important Safety Instructions To reduce the risk of fire, electric shock,... - Page 5 If this occurs, have washer checked by a qualified service person. F232134 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 20. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
-
Page 6: Safety Decals
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Be careful around the open door, particularly when loading from a level below the door. Impact with door edges can cause personal injury. -
Page 7: Operator Safety
Machine is not connected to a properly grounded circuit. F232134 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Do not bypass any safety devices in the machine. Never operate the machine with a bypassed or disconnected balance system. -
Page 8: Introduction
HC30MD2 HC80MV3 HC30ML2 NC18MD2 HC30MN2 NC18MDX HC30MX2 NC18MX2 HC30MY2 NC25MD2 HC35MC2 NC25MDX HC35MD2 NC25MX2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction NC27MD2 SC27MH2 NC27MDX SC27MN2 NC27MX2 SC27MV2 NC35MD2 SC27MX2 NC35MDX SC30MD2 NC35MX2 SC30ML2 NC50MD2... -
Page 9: Nameplate Location
Nameplate F232134 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Replacement Parts If literature or replacement parts are required, contact the source from whom the machine was... - Page 10 Option Identification (varies from machine to machine) 0001 * Denotes Brand *C60MX2OU60001 00000000000 208 – 240 500000 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Model Number Familiarization Guide C60MX20060001 Sample Model Number: EXAMPLE OF NAMEPLATE Figure 1 CHM2028N...
-
Page 11: Communications
For detailed information on the Central Pay System Communications, refer to the manufacturer. F232134 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Card Reader (Card Reader Models Only) The models are usually designated by the “Prep for Card Reader”... -
Page 12: Operation
The CYCLE INDICATOR dial displays current cycle step. The depressed pushbutton on the cycle selector switch indicates currently selected cycle. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation Operating Instructions 1. Turn on the main power source (circuit breaker). - Page 13 4. Close door and turn handle counterclockwise until button pops out. Refer to Figure 6. Figure 6 F232134 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5. Select wash cycle. Refer to Figure 7. CYCLE INDICATOR ADD BLEACH...
-
Page 14: Supply Dispenser
Refer to Figure 9. DELICATE KNITS WARM COLD Figure 9 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 10. Add bleach to container 2 when ADD BLEACH WHEN LIT is illuminated. Refer to Figure 10. Supply Dispenser B157R B157R... -
Page 15: Mechanical Timer Cycles
Shakeout Supply 1 Supply 3 * Cycle times are for the factory-preset jumper configuration. See Programming Manual for information. F232134 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Program Water Temperature Water Level Warm High Warm... -
Page 16: Maintenance
2. Inspect steam hose connections for leaks (where applicable). © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance 3. Check door interlock before starting operation: a. Attempt to start the machine with the door open. -
Page 17: Weekly
Motor Pulley Straightedge Basket Pulley Figure 11 F232134 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT c. For flat-pulley drive systems, verify allowable distance of belt from edge of pulley. Refer to Table 1 below. Model 50 –... - Page 18 This can result in overlubrication, causing damage to bearings and seals. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Figure 12 3. Remove back panel and check overflow hose and drain hose for leaks.
-
Page 19: Quarterly
Unscrew Cap. c. Remove Element and clean. d. Replace Element and Cap. F232134 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Filter Element Figure 13 7. Check the bearing mounting bolts to make sure they are torqued properly. Refer to Table 2 for specifications. -
Page 20: Care Of Stainless Steel
● overheating by scouring with a powder or by employing special chemical solutions. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Do not leave sanitizers or sterilizing solutions on ● stainless steel equipment for prolonged periods of time.
Need help?
Do you have a question about the Hardmount Coin and OPL and is the answer not in the manual?
Questions and answers