Advertisement
3
Connect HDMI cables to your video input devices and the HDMI ports on
the side and back of the WirelessHD Transmitter.
Note: You can connect up to five input devices to the transmitter. See
"Viewing WirelessHD content" for information on switching between
input sources.
4
To use the transmitter as a pass-through device to a television or other
display, connect an HDMI cable to the display device and the HDMI
output port on the rear of the WirelessHD Transmitter. See "Viewing
WirelessHD content" for information on switching between wireless and
wired display modes.
Viewing WirelessHD
content
1
Turn on your video device and begin playback.
2
Turn on the power switch on the side of the WirelessHD Transmitter.
3
Turn on the projector.
4
If you have connected a television or other display to the output port on
the transmitter and want to switch between wired and wireless display
modes, press the Output button on the remote control or transmitter.
The WiHD light on the transmitter will light up when the wireless
display mode is active.
5
Press the WirelessHD button on the projector remote control.
Note: If the WirelessHD connection fails, press the Setup button on the
bottom of the transmitter, then try again.
6
If you have connected multiple input devices to the transmitter, press
the Input button on the remote control or transmitter once to display
the sub-screen menu, then press the button again to switch between the
input devices.
7
To display two WirelessHD input devices simultaneously, press the P-in-P
button on the remote control to enable picture-in-picture mode. Press
and hold the P-in-P button for three seconds to switch the main image
and sub-screen, or press the P-in-P button again to disable picture-in-
picture mode.
See the online User's Guide for more information on adjusting and configuring
the WirelessHD connection and display modes.
Troubleshooting
If you see a blank screen or the No signal message after turning on your video
device or computer, check the following:
•
Make sure the power light on the projector is blue and not flashing.
•
Press the Source buttons on the projector or the remote control to switch
to the correct image source, if necessary.
•
If you're using a Windows
®
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
•
If you're using a Mac laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary, then
click the Arrange or Arrangement tab, and select the Mirror Displays
check box.
If 3D images aren't displaying properly, check the following:
•
Press the
button to switch to 3D viewing mode, if necessary.
•
Make sure that you are within the 3D viewing range. See "Choose a
location" on the front of this sheet or the online User's Guide for more
information.
•
Press the Menu button on your remote control, select the Signal menu,
then 3D Setup, then select 3D Format. Make sure that the Auto option is
selected.
•
Check that your video device and media are both 3D-compatible. Refer
to the documentation that came with your video device for more
information.
If WirelessHD content isn't displaying properly, check the following:
•
Check that the Link light on the transmitter is lit. If the light is flashing
slowly, the transmitter could not connect with the projector and has
entered standby mode. Verify that the projector is turned on and that all
cables are properly connected as shown in the "Connect the WirelessHD
Transmitter" section.
•
Make sure the WirelessHD Transmitter is within 32 feet (10 m) of the
projector, isn't obstructed by any large objects and is not placed on a
metal surface.
•
If you are viewing wireless content, make sure that the WiHD light on the
transmitter is lit. If it isn't, press the Output button on the remote control
or transmitter.
laptop, press the function key on your
. You may have to hold down the
Advertisement
