Multi-Function Door Control (Optional) - Chamberlain ATS Owner's Manual

Multi-Function Door Control (Optional)

INSTALLATION
Locate door control within sight of the door at a minimum
height of 5 feet (1.5 m) where small children cannot
reach, and away from moving parts of the door and door
hardware. If installing into drywall, drill 5/32" holes and
use anchors provided. For pre-wired installations (as in
new home construction), it may be mounted to a single
gang box. NOTE: After installation, a green indicator light
behind the cover will indicate proper connection. If not lit,
the Lock and Light features will not function (reverse wires
to correct).
1. Strip 1/4" (6 mm) of insulation from one end of bell
wire and connect to the two screw terminals on back
of door control by color: white wire to 2 and white/red
wire to 1.
2. Remove cover by gently pushing both thumbs against
upper corners of cover on back side of door control.
Fasten with 6ABx1-1/4" self-tapping screws (standard
installation) or 6-32x1" machine screws (into gang box)
as follows:
• Drill and install bottom screw, allowing 1/8" (3 mm)
to protrude above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fi t.
• Install top screw with care to avoid cracking plastic
housing. DO NOT overtighten.
• Insert bottom tabs and snap on cover. (To remove
cover after mounting, gently pry at top with paper
clip or small fl at head screwdriver.)
3. (Standard installation only) Run bell wire up wall and
across ceiling to motor unit. Use insulated staples to
secure wire in several places. DO NOT pierce wire with
a staple, creating a short or open circuit.
4. Connect bell wire to the opener terminal screws: white
to 2 and white/red to 1.
5. Use tacks or staples to permanently attach entrapment
warning label to wall near door control, and manual
release/safety reverse test label in a prominent location
on inside of garage door.
NOTE: DO NOT connect the power and operate the opener
at this time. The trolley will travel to the full open position
but will not return to the close position until the sensor
beam is connected and properly aligned. See safety
reversing sensor instructions beginning on page 15.
Multi-Function Door Control
Panel Terminal Screws
2-Conductor Bell Wire
Door Control
Push Bar
Lock
Button
Opener Terminal Screws
Light Opener Panel
Button
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is NOT connected BEFORE installing
door control.
• Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from
a closing garage door:
• Install door control within sight of garage door, out
of reach of children at a minimum height of 5 feet
(1.5 m), and away from ALL moving parts of door.
• NEVER permit children to operate or play with door
control push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to
door travel.
• ALWAYS keep garage door in sight until completely
closed. NEVER permit anyone to cross path of
closing garage door.
OPERATION OF THE MULTI-FUNCTION DOOR CONTROL
Press the push button to open or close
the door. Press again to reverse the
door during the closing cycle or to stop
the door while it's opening.
Light feature
Press the Light button to turn the
opener light on or off. It will not control
the opener lights when the door is in motion. If you turn it
on and then activate the opener, the light will remain on for
4-1/2 minutes. Press again to turn it off sooner. The 4-1/2
minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2
minutes as follows: Press and hold the Lock button until
the light blinks (about 10 seconds).
A single blink indicates that the timer is reset to 1-1/2
minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes. Repeat again
for a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
Lock feature
Designed to prevent operation of the door from hand-held
remote controls. However, the door will open and close
from the Door Control and the Keyless Entry Accessories.
To activate, press and hold the Lock
button for 2 seconds. The push bar light
will fl ash as long as the Lock feature is
on.
To turn off, press and hold the Lock
button again for 2 seconds. The push
bar light will stop fl ashing. The Lock
feature will also turn off whenever the
"learn" button on the motor unit panel is
activated.
Antenna
31
Lighted
Push
Button
Lock
Button
Light
Button