Replacing The Oven Light(S); Troubleshooting - Dacor MCS130S Use And Care Manual

Replacing
the Oven
Light(s) I
1.
The light assembly consists of a removable lens 2.
cover and 10-watt 120VAC halogen bulb, as well
as a light fixture housing. Light bulb replacement
is considered to be a homeowner maintenance
operation.
_ WARNINGS:
To prevent electrical shock and/or personal
injury:
1. Make certain that the appliance and
light bulb are cool and that power to the
appliance has been turned off before
replacing the light bulb.
2. Always ensure that the lens cover is
in place when using the appliance.
The lens cover protects the bulb from
breakage caused by high temperatures
or mechanical shock.
To replace a light bulb, follow these steps:
Turn off the power at the main power
supply.
Remove the lens cover from the housing
by pulling straight out.
_Lens Cover
Oven Light Assembly
Troubleshooting
I
NOTE:
In some cases the lens cover may be tight
enough to require the use of your light lens
pry stick. This prying tool should be used
with caution. Do not cause uneven stress on
the lens cover. Gently insert the point end
of the pry stick under the center edge of the
lens cover on the side facing the oven door.
Hold your hand under the lens for support
then pry out to remove the lens cover.
3. Pull the light bulb out and replace it with a
specia! !0-watt halogen bulb rated for use
in a Self-Cleaning oven. Use DACOR Part
No. 86364 available from any authorized
DACOR parts distributor or dealer.
4. Reinstall the lens cover by aligning the
cover over the opening and gently pressing
it into its original position.
5. Turn the power back on at the main power
supply.
Unnecessary service calls may be expensive, frustrating and time-consuming. Before you call for service, please review the potential problems, possible
causes and remedies shown below. Also, refer to the table on page !1 to view various oven failure codes that can be displayed by the clock. Failure
Codes will appear where the temperature is normally displayed.
IMPORTANT:
If a Failure Code is displayed, the oven will beep continuously until the user presses the "CANCEL,SECURE" button. The oven will not heat
after a failure. Call a qualified appliance technician to repair the oven.
Problem
1. Nothing works
Possible Cause
Oven is not connected to electrical power
Remedy
Have oven connected to a properly sized
electrical power supply by a qualified
electrician.
Power supply is not energized. Have an electrician check power supply,
including the house circuit breaker, wiring and
fuses
2. Oven wiii not heat..
Time of day is not set. Press "CLOCK" touch pad, then press
"TIME.TEMP" pad to set correct time of day.
Oven settings are not correct Follow mode selection and clock settings as
specified in OVEN OPERATION section.
Oven is set for Delay Timed Cooking. Oven will turn on automatically at preset time. I1
desired, press "CANCEL.SECURE" touch pad
to cancel out of Delay Timed Cooking.
Change rack position.
3. Clock displays incorrect time of day. Time of day is not set. Press "CLOCK" touch pad, then press
"TIME.TEMP" pad to set correct time of day.
Power supply has been interrupted. Reset time of day.
4. Foods over-cook.
Incorrect cooking time, temperature, or rack
position being used.
Adjust time or temperature.
Oven temperature calibration differs from your
previous oven.
Adjust oven temperature as per ADJUSTING
THE OVEN TEMPERATURE section.
5. Foods under-cook.
Incorrect cooking time, temperature, or rack
position being used.
Adjust time or temperature.
Oven temperature calibration differs from your
previous oven.
Adjust oven temperature as per ADJUSTING
THE OVEN TEMPERATURE section.
6. Oven does not Self-Clean.
Door is not shut tight, so automatic door latch
will not lock.
Close door tightly.
Troubleshooting Guide
10