Related Manuals for WELLTECH ATA-171 - V1.4
Summary of Contents for WELLTECH ATA-171 - V1.4
- Page 1 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide ATA-171/172/17 (ATA-S1/S2/P) User’s Guide V.1.4 2006/4/24...
-
Page 2: Table Of Contents
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Introduction............................2 Hardware Overview....................... 2 Software Overview ........................ 2 Keypad Interface for The ATA......................3 Setup the ATA by Web Browser......................4 Login............................4 System Information for the ATA..................... 5 Phone Book........................... 5 Phone Setting........................6 Network .......................... -
Page 3: Hardware Overview
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Introduction This user’s manual is for 1-port FXS VoIP terminal adapter (ATA). This user’s manual will explain the IVR instruction, web configuration, and command line configuration for the ATA. Before using the ATA, some setup processes are required to make the ATA work properly. Please refer to the Setup Menu for further information. -
Page 4: Keypad Interface For The Ata
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Keypad Interface for The ATA You can use the PSTN phone keypad to operate the ATA. Please follow the instruction to configure your terminal adapter. Group IVR Action IVR Menu Choice Parameter(s) Notes: Press O# can pass relay to PSTN Dial out from 0¡... -
Page 5: Setup The Ata By Web Browser
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Setup the ATA by Web Browser The ATA provides a built-in web server. You can use Web browser to configure the ATA. First please input the IP address in the Web page. In the end of IP address, please add the port number “:9999”. Ex: http://192.168.1.100:9999 Login. -
Page 6: System Information For The Ata
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide System Information for the ATA. 3.2.1 When you login the web page, you can see the ATA current system information like firmware version, company… etc in this page. 3.2.2 Also you can see the function lists in the left side. You can use mouse to click the function you want to set up. -
Page 7: Phone Setting
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 3. Speed Dial Phone Setting 3.4.1 In Phone Setting contains Call Forward, SNTP Settings, Volume Settings, Block Setting, Caller ID, Auto Dial Setting, Flash Time Setting, Call Waiting, and T.38(FAX) Setting functions. 3.4.2 Call Forward function: you can setup the phone number you want to forward in this page. There are three type of Forward mode. - Page 8 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 4. Forward Setting 3.4.3 SNTP Setting function: you can setup the primary and second SNTP Server IP Address, to get the date/time information. Also you can base on your location to set the Time Zone, and how long need to synchronize again.
- Page 9 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide 3.4.4 Volume Setting function: you can setup the Handset Volume, Ringer Volume, and the Handset Gain. When you finished the setting, please click the Submit button. Handset Volume is to set the volume for you can hear from the handset. Ringer Volume is to set the ringer volume for you can hear.
- Page 10 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 7. Block Setting 3.4.6 Caller ID function: you can set the device to show Caller ID in your PSTN Phone or IP Phone. There are four selection of Caller ID. You need to base on your environment to set the Caller ID function for FSK or DTMF.
- Page 11 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide 3.4.7 Auto Dial Setting function: This function is when you input the phone number by the keypad but you don’t need to press “#”. After time out the system will dial directly. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button.
- Page 12 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 10. Flash Time Setting 3.4.9 Call Waiting Setting function: You can Enable/Disable the Call Waiting function, When you are talking with someone, there is a new incoming call, you will hear the call waiting tone. When you finished the setting, please click the Submit button.
-
Page 13: Network
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide 3.4.10 T.38 Setting function: You can Enable/Disable the T.38 function. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically. - Page 14 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide 3.5.3 NAT Settings: The TA’s default setting is NAT mode. In this page you can configure the TA LAN and WAN port’s setting. LAN port is for you to connect to your PC or other Switch, and the WAN port is for you to connect to the ADSL Router, Broadband Router.
- Page 15 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide 3.5.4 Bridge Setting: If you don’t want to use the NAT Mode, then you can set the network setting in this page. The TCP/IP Configuration item is to setup the LAN port’s network environment. You may refer to your current network environment to configure the VoIP Phone properly.
- Page 16 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide 3.5.5 DDNS Setting: You can configure the DDNS setting in this page. You need to have the DDNS account and input the informations properly. You can have a DDNS account with a public IP address then others can call you via the DDNS account. But now most of the VoIP applications are work with a SIP Proxy Server.
-
Page 17: Ip Settings
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide going to the TA(with the TA’s IP address and the correct VID), and the VID is not these four VID you set, then the packets will be discard by the TA. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. - Page 18 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide (1-12) If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically. Figure 18.
- Page 19 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 19. Port Setting 3.6.4 Codec Settings: you can setup the Codec priority, RTP packet length, and VAD function in this page. You need to follow the ISP suggestion to setup these items. When you finished the setting, please click the Submit button.
- Page 20 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide 3.6.5 Codec ID Setting: Sometimes 2 VoIP device with different Codec ID will cause the interopability issue. If you are talking with others got some problems, you may ask the other one what kind of Codec ID he use, then you can change your Codec ID. When you finished the setting, please click the Submit button.
- Page 21 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 22. DTMF Setting 3.6.7 RPort Function: you can setup the RPort Enable/Disable in this page. To change this setting, please following your ISP information. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button.
-
Page 22: Nat Trans
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide 3.6.8 Other Settings: you can setup the Hold by RFC, Voice/SIP QoS and SIP expire time in this page. To change these settings please following your ISP information. When you finished the setting, please click the Submit button. The QoS setting is to set the voice packets’ priority. If you set the value higher than 0, then the voice packets will get the higher priority to the Internet. -
Page 23: Others
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 205. STUN Setting Others 3.8.1 In Others you can setup Auto Config, PTT Setting and ICMP Setting function. The function can configure your VoIP Phone automatically. 3.8.2 Auto Config: you can setup the Auto Configuration Enable/Disable and auto configuration by FTP or TFTP. - Page 24 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 216. Auto Configuration Setting 3.8.5 ICMP Setting: you can setup the ICMP echo Enable/Disable in this page. This function can disable echo when someone ping this device, it can avoid haker try to attack the device. When you finished the setting, please click the Submit button.
- Page 25 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 238. ICMP Setting 3.8.6 PTT Setting: you can setup the PTT in this page. When you are using different country’s PSTN Phone, you have to set the country’s setting to meet the requirement. When you finished the setting, please click the Submit button.
-
Page 26: System Auth
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide System Auth. 3.9.1 In System Authority you can change your login name and password. When you finished the setting, please click the Submit button. If there is nothing need to change, please click the Save Change Item in the left side, then click the Save button. The change you made will save into the system and the system will Reboot automatically. -
Page 27: Update
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 31. Save Change 3.11 Update 3.11.1 In Update you can update the ATA’s firmware to the new one or do the factory reset to let the ATA back to default setting. 3.11.2 In New Firmware function you can update new firmware via HTTP in this page. You can ugrade the firmware by the following steps: Select the firmware code type, Risc or DSP code. - Page 28 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 32. Update Firmware 3.11.3 In Default Setting you can restore the TA to factory default in this page. You can just click the Restore button, then the TA will restore to default and automatically restart again. The Default Setting will be NAT Mode, WAN port is DHCP Client Mode, LAN port is Fixed IP Mode and the IP Address is 192.168.123.1.
-
Page 29: Reboot
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Figure 33. Restore Default Setting 3.12 Reboot 3.12.1 Reboot function you can restart the ATA. If you want to restart the ATA, you can just click the Reboot button, then the ATA will automatically. Figure 34. Reboot System... -
Page 30: Setup The Ata By Using Console (Hyper Terminal)
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Setup the ATA by using Console (Hyper Terminal) Configure the COM port First Open the hyper terminal window, select the connection by the COM port, and then click the “Setting” button. Figure 25. Console Setting-1 Set the COM port’s setting as following setting. Then click OK. Figure 26. -
Page 31: Login Into The Ata
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Login into the ATA After finished the setting, click the “Connect” button (looks like a telephone icon). Then the hyper terminal is ready to connect to the ATA. Press “Enter” and the hyper terminal will show the “Login: “. Input “root” and press the “Enter”... -
Page 32: Using Cli Command To Configure The Ata
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Using CLI command to configure the ATA 4.3.1 CLI command list as below: Index Command Description Show CLI Command ARP Configuration ipconfig Interface Configuration save Save to flash reboot Reboot exit Exit debugmode Enter Debug Mode update Update Flash Code/RAM auth... - Page 33 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide Show 'ipconfig -ifN' Option Set Host Type Set MAC Address Set IP Address Set Net Mask Set Gateway -dns0 Set Primary DNS server -dns1 Set Secondary DNS server Set Default Route -nat Set NAT Enable Interface Disable Interface -dhcps DHCP Server Setting...
- Page 34 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide -sys1 Change System user1 user name/password -sys2 Change System user2 user name/password -sys3 Change System user3 user name/password -sys4 Change System user4 user name/password -norm0 Change Normal user0 user name/password -norm1 Change Normal user1 user name/password -norm2 Change Normal user2 user name/password -norm3...
- Page 35 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide -13- sip function Index Command Description Show 'sip' Option -proxy0 sip -proxy0 -proxy1 sip -proxy1 -proxy2 sip -proxy2 -upnp sip -upnp on/off/show -exts sip -exts sip upnp external-port -extr sip -extr rtp upnp external-port -sipp sip udp port -rtpp sip rtp port -stun...
- Page 36 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide -16- vlan function Index Command Description Show 'vlan' Option Tx Vlan setting Rx Vlan setting (null) Show Vlan Setting -17- time function Index Command Description Show 'Time' Option Modify Time: hour:min:sec Modify date: year:mon:date (null) Show Data & Time -18- mactab function is to show MAC learning table.
- Page 37 ATA-171/172/171P (ATA-S1/S2/P) User’s Guide -24- weblogo function Index Command Description Show 'weblogo' Option Vender Logo -off Default Logo (null) Show weblogo Setting -25- dsp function is to show dsp code type. -26- addport function is to add Nat Port Mapping -27- cid function Index...
-
Page 38: How To Make A Phone Call
ATA-171/172/171P (ATA-S1/S2/P) User’s Guide How to make a phone call When your ATA is configured properly, you can make a phone call to your friend in the same Service provider. If you want to make a phone call, you can dial the phone number and press “#” button to start to dial the phone number.