TP-Link TL-WR702N User Manual
  1. Manuals
  2. Brands
  3. TP-Link Manuals
  4. Wireless Router
  5. TL-WR702N
  6. User manual

TP-Link TL-WR702N User Manual

150mbps wireless n nano router
Hide thumbs Also See for TL-WR702N:
Table of Contents

Advertisement

Quick Links

See also: User Manual
TL-WR702N
150Mbps Wireless N Nano Router
Rev: 1.0.0
1910010547

Advertisement

Table of Contents
loading

Related Manuals for TP-Link TL-WR702N

Summary of Contents for TP-Link TL-WR702N

  • Page 1 TL-WR702N 150Mbps Wireless N Nano Router Rev: 1.0.0 1910010547...

  • Page 2: Fcc Statement

    Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.

  • Page 3: Ce Mark Warning

    FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations.

  • Page 4: Declaration Of Conformity

    Audio/Video, information and communication technology equipment- Environmentally conscious design EN62075:2008 Person is responsible for marking this declaration: Yang Hongliang Product Manager of International Business TP-LINK TECHNOLOGIES CO., LTD . South Building, No.5 Keyuan Road, Central Zone, Science & Technology Park, Nanshan, Shenzhen, P. R. China...

  • Page 5: Table Of Contents

    CONTENTS Package Contents..........................1 Chapter 1. Introduction........................2 Overview of the Router .......................2 Conventions ........................3 Main Features ........................3 Panel Layout ........................4 Chapter 2. Connecting the Router .....................5 System Requirements......................5 Installation Environment Requirements ................5 Connecting the Router ......................5 Chapter 3. Quick Installation Guide....................10 TCP/IP Configuration .......................
  • Page 6 5.12 IP & MAC Binding Setting ....................94 5.13 Dynamic DNS........................96 5.14 System Tools........................98 Chapter 6. Configuration for Repeater Mode ................107 Login ..........................107 Status ..........................107 Quick Setup........................108 Working Mode ........................ 109 Network .......................... 109 Wireless ..........................110 DHCP ..........................112 System Tools........................116...

  • Page 7: Package Contents

    Quick Installation Guide One Power Adapter One USB Cable One RJ-45 Ethernet Cable One Resource CD for TL-WR702N 150Mbps Wireless N Nano Router, including: • User Guide • Other Helpful Information Note: Make sure that the package contains the above items. If any of the listed items is damaged or missing, please contact with your distributor.

  • Page 8: Chapter 1. Introduction

    TL-WR702N to work as a router for network sharing with high speed. The functions of Repeater mode and AP Bridge mode are similar, for they both make the TL-WR702N able to extend the existing wireless network. In Client mode, TL-WR702N acts as a wireless station to enable the wired host(s) to access AP.

  • Page 9: Conventions

    Before installing the Router, please look through this guide to know all the Router’s functions. 1.2 Conventions The Router or TL-WR702N mentioned in this guide stands for TL-WR702N 150Mbps Wireless N Nano Router without any explanation. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation.

  • Page 10: Panel Layout

    TL-WR702N 150Mbps Wireless N Nano Router 1.4 Panel Layout Figure 1-1 TL-WR702N sketch Status Indication Solid It’s powered on but the LAN/WAN port is not connected. Flashing The LAN/WAN cable is connected but there is no data Slowly being transmitted or received.

  • Page 11: Chapter 2. Connecting The Router

    TL-WR702N 150Mbps Wireless N Nano Router Chapter 2. Connecting the Router 2.1 System Requirements Each PC in the LAN needs a working Ethernet Adapter TCP/IP protocol must be installed on each PC Web browser, such as Microsoft Internet Explorer 5.0 or later, Mozilla Firefox, Apple Safari...

  • Page 12: Router Mode

    150Mbps Wireless N Nano Router 2.3.1 AP Mode As the supplement of wired LAN, TL-WR702N enables the wired LAN to connect to the Internet wirelessly. The default mode of TL-WR702N is AP. Plug the power plug of TL-WR702N in electrical wall socket and connect the Ethernet cable correctly, you can surf the Internet by connecting your PC(s) to the Router wirelessly.

  • Page 13: Repeater Mode

    On this mode, the only wired port works as LAN. Computer could connect to the device by either wired or wireless way. The SSID of TL-WR702N should be the same as that of the device you repeat. To avoid the conflict of DHCP service with front-end devices, the DHCP server is default to be closed on this mode.

  • Page 14: Bridge Mode

    Router from the PC/notebook to set the Router in AP Repeater mode. 2.3.4 Bridge Mode Similar to the Bridge mode, TL-WR702N in Bridge mode is also used to extend the range of wireless signal of the existing AP or wireless router.
  • Page 15 150Mbps Wireless N Nano Router Figure 2-5 Hardware Installation of the TL-WR702N in Client Mode Connect the PC to the LAN/WAN port of TL-WR702N router with an Ethernet cable. Plug the power plug of TL-WR702N in electrical wall socket. Power on the PC(s).

  • Page 16: Chapter 3. Quick Installation Guide

    TL-WR702N 150Mbps Wireless N Nano Router Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your TL-WR702N 150Mbps Wireless N Nano Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the TL-WR702N 150Mbps Wireless N Nano Router is 192.168.0.254.
  • Page 17 TL-WR702N 150Mbps Wireless N Nano Router Figure 3-1 Success result of Ping command If the result displayed is similar to the Figure 3-2, it means the connection between your PC and the Router has failed. Figure 3-2 Failure result of Ping command...

  • Page 18: Quick Installation Guide

    150Mbps Wireless N Nano Router 3.2 Quick Installation Guide With a Web-based utility, it is easy to configure and manage the TL-WR702N 150Mbps Wireless N Nano Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
  • Page 19 The Router supports five working modes for multi-user to access the Internet: AP, Router, Repeater, Bridge and Client. In AP mode, TL-WR702N enables the wired LAN to connect to the Internet wirelessly. In Router mode, it can access the Internet via DSL/Cable Modem. In Repeater mode, the device will relay data to an associated root AP.
  • Page 20 TL-WR702N 150Mbps Wireless N Nano Router Figure 3-6 Quick Setup - Wireless AP Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list. SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network.
  • Page 21 TL-WR702N 150Mbps Wireless N Nano Router • 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients. • 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless stations can connect to the Router.
  • Page 22 TL-WR702N 150Mbps Wireless N Nano Router Figure 3-8 Quick Setup – Finish 3.2.2 Router Mode When you choose Router on Working Mode page in Figure 3-5 , take the following steps: Click Next in Figure 3-5, and you will see the following screen. The wireless settings on Router mode are the same as that on AP mode.
  • Page 23 TL-WR702N 150Mbps Wireless N Nano Router Figure 3-10 Quick Setup - WAN Connection Type The Router supports three popular ways PPPoE, Dynamic IP and Static IP to connect to the Internet. To make sure the connection type your ISP provides, please refer to the ISP. Make sure the cable is securely plugged into the WAN port before detection.
  • Page 24 TL-WR702N 150Mbps Wireless N Nano Router Figure 3-12 Quick Setup - Static IP Click Next, you will see the Finish page as shown in Figure 3-13. Click the Reboot button to make your wireless configuration take effect and finish the Quick Setup.
  • Page 25 TL-WR702N 150Mbps Wireless N Nano Router Figure 3-14 Quick Setup - Wireless Repeater SSID - The SSID of AP that you want to access. MAC of AP - The MAC address of AP that you want to access. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used.
  • Page 26 TL-WR702N 150Mbps Wireless N Nano Router Figure 3-15 AP List Note: If you know the SSID of the desired AP, you can also input it into the field "SSID" manually. Click the Next button in Figure 3-14. You will then see the Finish page.
  • Page 27 TL-WR702N 150Mbps Wireless N Nano Router Figure 3-16 Quick Setup - Finish 3.2.4 Bridge Mode When you choose Bridge on Working Mode page in Figure 3-5 , take the following steps: Click Next, and then Wireless Repeater page will appear as shown in Figure 3-17.
  • Page 28 TL-WR702N 150Mbps Wireless N Nano Router Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field.
  • Page 29 TL-WR702N 150Mbps Wireless N Nano Router PassWord - If the AP your Router is going to connect needs password, you need to fill the password in this blank. Click Survey button on the Wireless page as shown in Figure 3-17, and then AP List page will appear as shown in Figure 3-18.
  • Page 30 TL-WR702N 150Mbps Wireless N Nano Router Figure 3-19 Quick Setup - Wireless Security Settings This page is for setting wireless security of your own AP. When computers and mobile phones are connected to the AP, they should input the same password.
  • Page 31 TL-WR702N 150Mbps Wireless N Nano Router Figure 3-21 Quick Setup - Wireless Client SSID - Enter the SSID that you want to access. MAC of AP - Enter the MAC address of AP that you want to access. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used.
  • Page 32 TL-WR702N 150Mbps Wireless N Nano Router Figure 3-22 AP List Click the Next button in Figure 3-23. You will then see the Finish page. Click the Reboot button to make your wireless configuration take effect and finish the Quick Setup.
  • Page 33 TL-WR702N 150Mbps Wireless N Nano Router Note: 1. The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For best results, place your Router. Near the center of the area in which your wireless stations will operate.

  • Page 34: Chapter 4. Configuration For Ap Mode

    TL-WR702N 150Mbps Wireless N Nano Router Chapter 4. Configuration for AP Mode This chapter will show each Web page's key functions and the configuration way for AP Mode of TL-WR702N. 4.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility.
  • Page 35 TL-WR702N 150Mbps Wireless N Nano Router Figure 4-2 Status Firmware Version - The version information of the Router’s firmware. Hardware Version - The version information of the Router’s hardware. LAN - This field displays the current settings or information for the LAN, you can configure them in the Network >...

  • Page 36: Quick Setup

    TL-WR702N 150Mbps Wireless N Nano Router • Channel Width - The current wireless channel width in use. • MAC address - The physical address of the Router, as seen from the WLAN. • WDS Status - The status of WDS connection.

  • Page 37: Network

    TL-WR702N 150Mbps Wireless N Nano Router Figure 4-4 4.5 Network Figure 4-5 the Network menu There is only one submenu under the Network menu (shown in Figure 4-5): LAN. 4.5.1 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below.

  • Page 38: Wireless

    TL-WR702N 150Mbps Wireless N Nano Router 4.6 Wireless Figure 4-7 Wireless menu There are five submenus under the Wireless menu (shown in Figure 4-7): Wireless Settings, Wireless Security, MAC Filtering, Wireless Advanced and Wireless Statistics. Click any of them, and you will be able to configure the corresponding function.
  • Page 39 TL-WR702N 150Mbps Wireless N Nano Router name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used.
  • Page 40 TL-WR702N 150Mbps Wireless N Nano Router SSID (to be bridged) - The SSID of the AP your Router is going to connect to as a client. You can also use the search function to select the SSID to join. BSSID (to be bridged) - The BSSID of the AP your Router is going to connect to as a client.

  • Page 41: Wireless Security

    TL-WR702N 150Mbps Wireless N Nano Router 2. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the Router. 4.6.2 Wireless Security Choose menu “Wireless → Wireless Security”, and then you can configure the security settings of your wireless network.
  • Page 42 TL-WR702N 150Mbps Wireless N Nano Router • Type - you can choose the type for the WEP security on the pull-down list. The default setting is Automatic, which can select Shared Key or Open System authentication type automatically based on the wireless station's capability and request.

  • Page 43: Mac Filtering

    TL-WR702N 150Mbps Wireless N Nano Router key of WPA) or WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request. • Encryption - When WPA-PSK or WPA is set as the Authentication Type, you can select Automatic (Recommended), TKIP or AES as Encryption.
  • Page 44 TL-WR702N 150Mbps Wireless N Nano Router Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, shown in Figure 4-11:...

  • Page 45: Wireless Advanced

    TL-WR702N 150Mbps Wireless N Nano Router 1. Click the Enable button to enable this function. 2. Select the radio button “Allow the stations specified by any enabled entries in the list to access” for Filtering Rules. 3. Delete all or disable all entries if there are any entries already.

  • Page 46: Wireless Statistics

    TL-WR702N 150Mbps Wireless N Nano Router Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here.

  • Page 47: Dhcp

    TL-WR702N 150Mbps Wireless N Nano Router Figure 4-13 Wireless Statistics MAC Address - The connected wireless station's MAC address Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN /...
  • Page 48 TL-WR702N 150Mbps Wireless N Nano Router Figure 4-15 DHCP Settings DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.

  • Page 49: Dhcp Clients List

    TL-WR702N 150Mbps Wireless N Nano Router 4.7.2 DHCP Clients List Choose menu “DHCP → DHCP Clients List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 4-16. Figure 4-16 DHCP Clients List...

  • Page 50: System Tools

    TL-WR702N 150Mbps Wireless N Nano Router Status - The status of this entry either Enabled or Disabled. To Reserve an IP address: Click the Add New… button. Then Figure 4-18 will pop-up. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) and IP address (in dotted-decimal notation) of the computer for which you want to reserve an IP address.
  • Page 51 TL-WR702N 150Mbps Wireless N Nano Router Choose menu “System Tools”, and then you can see the submenus under the main menu: Diagnostic, Firmware, Factory Defaults, Backup & Restore, Reboot, Password, and System Log. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below.
  • Page 52 150Mbps Wireless N Nano Router IP Address/Domain Name - Type the destination IP address (e.g. 202.108.22.5) or Domain name (e.g. http://www.tp-link.com). Pings Count - The number of Ping packets for a Ping connection. The default is 4. Ping Packet Size - The size of Ping packet. The default is 64.

  • Page 53: Factory Defaults

    3. Click the Upgrade button. Note: New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Router rather than the configuration, you can try to upgrade the firmware.
  • Page 54 TL-WR702N 150Mbps Wireless N Nano Router Note: All changed settings will be lost when defaults are restored. 4.8.4 Backup & Restore Choose menu “System Tools → Backup & Restore”, and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 4-24.
  • Page 55 TL-WR702N 150Mbps Wireless N Nano Router • Change the LAN IP Address (system will reboot automatically). • Change the DHCP Settings. • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically).

  • Page 56: System Log

    TL-WR702N 150Mbps Wireless N Nano Router 4.8.7 System Log Choose menu “System Tools → System Log”, and then you can view the logs of the Router. Figure 4-27 System Log Refresh - Refresh the page to show the latest log list.

  • Page 57: Chapter 5. Configuration For Router Mode

    Chapter 5. Configuration for Router Mode This chapter will show each Web page's key functions and the configuration way for Router Mode of TL-WR702N. 5.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility.
  • Page 58 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-2 Firmware Version - The version information of the Router’s firmware. Hardware Version - The version information of the Router’s hardware. - 52 -...
  • Page 59 TL-WR702N 150Mbps Wireless N Nano Router LAN - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page. • MAC Address - The physical address of the Router, as seen from the LAN.

  • Page 60: Quick Setup

    TL-WR702N 150Mbps Wireless N Nano Router • Received (Packets) - Traffic that counted in packets has been received out from the WAN port. System Up Time - The length of the time since the Router was last powered on or reset.

  • Page 61: Network

    TL-WR702N 150Mbps Wireless N Nano Router 5.5 Network Figure 5-5 the Network menu There are three submenus under the Network menu (shown in Figure 5-5): WAN, LAN and MAC Clone. Click any of them, and you will be able to configure the corresponding function.
  • Page 62 TL-WR702N 150Mbps Wireless N Nano Router This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters.
  • Page 63 TL-WR702N 150Mbps Wireless N Nano Router IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. Default Gateway - (Optional) Enter the gateway IP address in dotted-decimal notation provided by your ISP.
  • Page 64 TL-WR702N 150Mbps Wireless N Nano Router Secondary Connection - It’s available only for PPPoE Connection. If your ISP provides an extra Connection type such as Dynamic/Static IP to connect to a local area network, then you can check the radio button of Dynamic/Static IP to activate this secondary connection.
  • Page 65 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-9 PPPoE Advanced Settings MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP.
  • Page 66 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-10 WAN – L2TP/Russia L2TP User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connect button to connect immediately.
  • Page 67 TL-WR702N 150Mbps Wireless N Nano Router Connect Manually - You can configure the Router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again.
  • Page 68 TL-WR702N 150Mbps Wireless N Nano Router User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name.

  • Page 69: Mac Clone

    TL-WR702N 150Mbps Wireless N Nano Router 5.5.2 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 5-12 LAN MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can't be changed.

  • Page 70: Wireless

    TL-WR702N 150Mbps Wireless N Nano Router Some ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here. WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX-XX-XX-XX-XX-XX format (X is any hexadecimal digit).
  • Page 71 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-15 Wireless Settings - Router SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address).
  • Page 72 TL-WR702N 150Mbps Wireless N Nano Router Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless stations can connect to the Router. When 802.11n mode is selected, only 802.11n wireless stations can connect to the AP. It is strongly recommended that you set the Mode to 802.11b/g/n, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the...
  • Page 73 TL-WR702N 150Mbps Wireless N Nano Router Authentication Type - This option should be chosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the authorization type of the Root AP. Password - If the AP your Router is going to connect needs password, you need to fill the password in this blank.
  • Page 74 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-16 Wireless Security Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. But it’s strongly recommended to choose one of the following modes to enable security.
  • Page 75 TL-WR702N 150Mbps Wireless N Nano Router • WEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network.
  • Page 76 TL-WR702N 150Mbps Wireless N Nano Router For ASCII, the key can be made up of any numbers 0 to 9 and any letters A to Z, the length should be between 8 and 63 characters. For Hexadecimal, the key can be made up of any numbers 0 to 9 and letters A to F, the length should be between 8 and 64 characters.
  • Page 77 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-18 Add or Modify Wireless MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follow these instructions: Enter the appropriate MAC Address into the MAC Address field. The format of the MAC...
  • Page 78 TL-WR702N 150Mbps Wireless N Nano Router 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New... button. 1) Enter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB-00-07-5F in the MAC Address field. 2) Enter wireless station A/B in the Description field.
  • Page 79 TL-WR702N 150Mbps Wireless N Nano Router Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the Router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100.

  • Page 80: Dhcp

    TL-WR702N 150Mbps Wireless N Nano Router Figure 5-20 Wireless Statistics MAC Address - The connected wireless station's MAC address Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN /...
  • Page 81 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-22 DHCP Settings DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.
  • Page 82 TL-WR702N 150Mbps Wireless N Nano Router 5.7.2 DHCP Clients List Choose menu “DHCP → DHCP Clients List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 5-23. Figure 5-23 DHCP Clients List...

  • Page 83: Forwarding

    TL-WR702N 150Mbps Wireless N Nano Router Status - The status of this entry, either Enabled or Disabled. To Reserve an IP address: Click the Add New… button. Then will pop-up. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) and IP address (in dotted-decimal notation) of the computer for which you want to reserve an IP address.

  • Page 84: Virtual Servers

    TL-WR702N 150Mbps Wireless N Nano Router 5.8.1 Virtual Servers Choose menu “Forwarding → Virtual Servers”, and then you can view and add virtual servers in the screen as shown in Figure 5-27. Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and FTP.

  • Page 85: Port Triggering

    TL-WR702N 150Mbps Wireless N Nano Router Figure 5-28 Add or Modify a Virtual Server Entry Note: If your computer or server has more than one type of available service, please select another service, and enter the same IP Address for that computer or server.
  • Page 86 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-29 Port Triggering Once the Router is configured, the operation is as follows: 1. A local host makes an outgoing connection using a destination port number defined in the Trigger Port field. 2. The Router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host.
  • Page 87 TL-WR702N 150Mbps Wireless N Nano Router Select Enable in Status field. Click the Save button to save the new rule. Figure 5-30 Add or Modify a Port Triggering Entry To modify or delete an existing entry: Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete.
  • Page 88 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-31 DMZ To assign a computer or server to be a DMZ server: Check the Enable radio button. Enter the IP Address of a local host in the DMZ Host IP Address field.

  • Page 89: Security

    TL-WR702N 150Mbps Wireless N Nano Router • Protocol - The type of protocol the Router opens for the application. • Internal Port - The Internal port the Router opens for local host. • IP Address - The IP address of the UPnP device that is currently accessing the Router.

  • Page 90: Ip Address Filtering

    TL-WR702N 150Mbps Wireless N Nano Router Enable Firewall - the general firewall switch is on or off. Enable IP Address Filtering - set IP Address Filtering is enabled or disabled. There are two default filtering rules of IP Address Filtering, either Allow or Deny passing through the router.
  • Page 91 TL-WR702N 150Mbps Wireless N Nano Router Effective Time - Enter a range of time in HHMM format, which point to the range time for the entry to take effect. For example, 0803 - 1705, the entry will take effect from 08:03 to 17:05.

  • Page 92: Domain Filtering

    TL-WR702N 150Mbps Wireless N Nano Router 5.9.3 Domain Filtering The Domain Filtering page allows you to control access to certain websites on the Internet by specifying their domains or key words. Figure 5-37 Domain Filtering Before adding a Domain Filtering entry, you must ensure that Enable Firewall and Enable Domain Filtering have been selected on the Firewall page.

  • Page 93: Mac Address Filtering

    TL-WR702N 150Mbps Wireless N Nano Router Click the Disabled All button to make all entries disabled. Click the Delete All button to delete all entries Click the Next button to go to the next page and the Previous button to return to the previous page.
  • Page 94 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-40 Add or Modify a MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follow these instructions: Enter the appropriate MAC Address into the MAC Address field. The format of the MAC...

  • Page 95: Remote Management

    TL-WR702N 150Mbps Wireless N Nano Router 5.9.5 Remote Management You can configure the Remote Management function on this page. This feature allows you to manage your Router from a remote location, via the Internet. Figure 5-41 Remote Management Web Management Port - Web browser access normally uses the standard HTTP service port 80.
  • Page 96 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-42 Advanced Security settings Packets Statistic interval (5 ~ 60) - The default value is 10. Select a value between 5 and 60 seconds in the pull-down list. The Packets Statistic interval value indicates the time section of the packets statistic.

  • Page 97: Static Routing

    TL-WR702N 150Mbps Wireless N Nano Router Ignore Ping Packet from WAN Port - Enable or Disable ignore ping packet from WAN port. The default is disabled. If enabled, the ping packet from the Internet cannot access the router. Forbid Ping Packet from LAN Port - Enable or Disable forbidding Ping Packet to access the router from the LAN port.

  • Page 98: Ip Qos

    TL-WR702N 150Mbps Wireless N Nano Router To add static routing entries: Click the Add New button. Enter the following data: Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route.
  • Page 99 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-46 IP QoS Enable IP QoS - Enable or disable the function of IP QoS. Choose BandWidth Type - Select the network connection type from the drop-down list. Bandwidth Apply - The bandwidth you get. If you are not clear about that, please contact with your ISP for help.

  • Page 100: Ip & Mac Binding Setting

    TL-WR702N 150Mbps Wireless N Nano Router IP address range for different entries could not have intersection with each other. After the configurations, click the Save button for the change to take effect. 5.12 IP & MAC Binding Setting Figure 5-47 the IP & MAC Binding menu There are two submenus under the IP &...
  • Page 101 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-49 IP & MAC Binding Setting (Add & Modify) To add IP & MAC Binding entries: Click the Add New.. button. Enter the MAC Address and IP Address. Select the Bind checkbox. Click the Save button to save it.

  • Page 102: Dynamic Dns

    TL-WR702N 150Mbps Wireless N Nano Router Click the Delete All button to delete all entries. 5.12.2 ARP List To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could configure the items on the ARP list also.
  • Page 103 TL-WR702N 150Mbps Wireless N Nano Router sign up for DDNS service providers such as www.dyndns.org, www.oray.net or www.comexe.cn. The Dynamic DNS client service provider will give you a password or key. 5.13.1 Oray.net DDNS If your selected dynamic DNS Service Provider is www.oray.net, the page will appear as shown in Figure 5-52: Figure 5-52 Oray.net DDNS Settings...

  • Page 104: System Tools

    TL-WR702N 150Mbps Wireless N Nano Router 5.14 System Tools Figure 5-53 The System Tools menu There are nine submenus under the System Tools menu: Time, Diagnostic, Firmware, Factory Defaults, Backup and Restore, Reboot, Password, Log and Statistics. Click any of them, and you will be able to configure the corresponding function.
  • Page 105 TL-WR702N 150Mbps Wireless N Nano Router To set time manually, follow the steps below: Select your local time zone. Enter the Date in Month/Day/Year format. Enter the Time in Hour/Minute/Second format. Click Save. For automatic time synchronization: Enter the address of the NTP Server I or NTP Server II.
  • Page 106 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-55 Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic too. • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway.
  • Page 107 The page allows you to upgrade the latest version firmware to keep your router up-to-date. Figure 5-57 Firmware Upgrade New firmware is posted at http://www.tp-link.com and can be downloaded for free. If the router is not experiencing difficulties, there is no need to upgrade firmware, unless the new firmware supports a new feature you need.
  • Page 108 Set your IP address as static IP before upgrading. To upgrade the router's firmware, follow these instructions: Download the latest firmware upgrade file from the TP-LINK website http://www.tp-link.com. Enter or select the path name where you save the downloaded file on the computer into the File blank.
  • Page 109 TL-WR702N 150Mbps Wireless N Nano Router Figure 5-59 Backup & Restore Configuration Click the Backup button to save all configuration settings as a backup file in your local computer. To restore the router's configuration, follow these instructions: • Click the Browse button to select the backup file which you want to restore.
  • Page 110 TL-WR702N 150Mbps Wireless N Nano Router 5.14.7 Password This page allows you to change the factory default user name and password of the router. Figure 5-61 Password It is recommended strongly that you change the factory default user name and password of the router.
  • Page 111 TL-WR702N 150Mbps Wireless N Nano Router Click the Refresh button to refresh the logs. Click the Clear All button to clear all the logs. 5.14.9 Statistics The Statistics page displays the network traffic of each PC in LAN, including total traffic and traffic of the last Packets Statistic interval seconds.
  • Page 112 TL-WR702N 150Mbps Wireless N Nano Router The total amount of the UDP packets transmitted to WAN in the UDP Tx last Packets Statistic interval seconds. The total amount of the TCP SYN packets transmitted to WAN in TCP SYN Tx the last Packets Statistic interval seconds.

  • Page 113: Chapter 6. Configuration For Repeater Mode

    Chapter 6. Configuration for Repeater Mode This chapter will show each Web page's key functions and the configuration way for Repeater Mode of TL-WR702N. 6.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility.

  • Page 114: Quick Setup

    TL-WR702N 150Mbps Wireless N Nano Router Figure 6-2 Status Firmware Version - The version information of the Router’s firmware. Hardware Version - The version information of the Router’s hardware. LAN - This field displays the current settings or information for the LAN, you can configure them in the Network >...

  • Page 115: Working Mode

    TL-WR702N 150Mbps Wireless N Nano Router 6.4 Working Mode The Router supports five operation mode types: AP, Router, Repeater, Bridge and Client. Please select one your want. Click Save to save your choice, which is shown as Figure 4-3. Figure 6-3 Working Mode AP - The wireless access point mode.

  • Page 116: Wireless

    TL-WR702N 150Mbps Wireless N Nano Router 6.5.1 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 6-6 LAN MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can't be changed.
  • Page 117 TL-WR702N 150Mbps Wireless N Nano Router Figure 6-8 Wireless Settings - Repeater SSID - The SSID of AP that you want to access. MAC of AP - The MAC address of AP that you want to access. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used.

  • Page 118: Dhcp

    TL-WR702N 150Mbps Wireless N Nano Router Near the center of the area in which your wireless stations will operate. In an elevated location such as a high shelf. Away from the potential sources of interference, such as PCs, microwaves, and cordless phones.
  • Page 119 TL-WR702N 150Mbps Wireless N Nano Router Figure 6-10 DHCP Settings DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.
  • Page 120 TL-WR702N 150Mbps Wireless N Nano Router To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 6.7.2 DHCP Clients List Choose menu “DHCP → DHCP Clients List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 6-11.
  • Page 121 TL-WR702N 150Mbps Wireless N Nano Router MAC Address - The MAC address of the PC for which you want to reserve an IP address. Reserved IP Address - The IP address reserved for the PC by the Router. Status - The status of this entry either Enabled or Disabled.

  • Page 122: System Tools

    TL-WR702N 150Mbps Wireless N Nano Router System Tools Figure 6-14 The System Tools menu Choose menu “System Tools”, and then you can see the submenus under the main menu: Diagnostic, Firmware, Factory Defaults, Backup & Restore, Reboot, Password, and System Log.
  • Page 123 Domain Name System (DNS) queries. IP Address/Domain Name - Type the destination IP address (e.g. 202.108.22.5) or Domain name (e.g. http://www.tp-link.com). Pings Count - The number of Ping packets for a Ping connection. The default is 4.
  • Page 124 Click the Upgrade button. Note: New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Router rather than the configuration, you can try to upgrade the firmware.
  • Page 125 TL-WR702N 150Mbps Wireless N Nano Router Figure 6-18 Restore Factory Default Click the Restore button to reset all configuration settings to their default values. • The default User Name: admin • The default Password: admin • The default IP Address: 192.168.0.254 •...
  • Page 126 TL-WR702N 150Mbps Wireless N Nano Router 6.8.5 Reboot Choose menu “System Tools → Reboot”, and then you can click the Reboot button to reboot the Router via the next screen. Figure 6-20 Reboot the Router Some settings of the Router will take effect only after rebooting, including: •...
  • Page 127 TL-WR702N 150Mbps Wireless N Nano Router It is strongly recommended that you should change the factory default user name and password of the Router, because all users who try to access the Router's Web-based utility or Quick Setup will be prompted for the Router's default user name and password.

  • Page 128: Chapter 7. Configuration For Bridge Mode

    Chapter 7. Configuration for Bridge Mode This chapter will show each Web page's key functions and the configuration way for Bridge Mode of TL-WR702N. 7.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility.
  • Page 129 TL-WR702N 150Mbps Wireless N Nano Router Figure 7-2 Status Firmware Version - The version information of the Router’s firmware. Hardware Version - The version information of the Router’s hardware. LAN - This field displays the current settings or information for the LAN, you can configure them in the Network >...

  • Page 130: Quick Setup

    TL-WR702N 150Mbps Wireless N Nano Router • MAC address - The physical address of the Router, as seen from the WLAN. • WDS Status - The status of WDS connection. System Up Time - The length of the time since the Router was last powered on or reset.

  • Page 131: Network

    TL-WR702N 150Mbps Wireless N Nano Router Figure 7-4 7.5 Network Figure 7-5 the Network menu There is only one submenu under the Network menu (shown in Figure 7-5): LAN. 7.5.1 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below.

  • Page 132: Wireless

    TL-WR702N 150Mbps Wireless N Nano Router 7.6 Wireless Figure 7-7 Wireless menu There are two submenus under the Wireless menu (shown in Figure 7-7): Wireless Settings and Wireless Security. Click any of them, and you will be able to configure the corresponding function.
  • Page 133 TL-WR702N 150Mbps Wireless N Nano Router name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used.
  • Page 134 TL-WR702N 150Mbps Wireless N Nano Router Authentication Type - This option should be chosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the authorization type of the Root AP. Password - If the AP your Router is going to connect needs password, you need to fill the password in this blank.
  • Page 135 TL-WR702N 150Mbps Wireless N Nano Router Figure 7-9 Wireless Security Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. But it’s strongly recommended to choose one of the following modes to enable security.
  • Page 136 TL-WR702N 150Mbps Wireless N Nano Router • WEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network.

  • Page 137: Dhcp

    TL-WR702N 150Mbps Wireless N Nano Router For ASCII, the key can be made up of any numbers 0 to 9 and any letters A to Z, the length should be between 8 and 63 characters. For Hexadecimal, the key can be made up of any numbers 0 to 9 and letters A to F, the length should be between 8 and 64 characters.
  • Page 138 TL-WR702N 150Mbps Wireless N Nano Router Figure 7-11 DHCP Settings DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.
  • Page 139 TL-WR702N 150Mbps Wireless N Nano Router Note: To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 7.7.2 DHCP Clients List Choose menu “DHCP → DHCP Clients List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 7-12.
  • Page 140 TL-WR702N 150Mbps Wireless N Nano Router Figure 7-13 Address Reservation MAC Address - The MAC address of the PC for which you want to reserve an IP address. Reserved IP Address - The IP address reserved for the PC by the Router.

  • Page 141: System Tools

    TL-WR702N 150Mbps Wireless N Nano Router Click the Next button to go to the next page and Click the Previous button to return the previous page. System Tools Figure 7-15 The System Tools menu Choose menu “System Tools”, and then you can see the submenus under the main menu: Diagnostic, Firmware, Factory Defaults, Backup &...
  • Page 142 TL-WR702N 150Mbps Wireless N Nano Router Figure 7-16 Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway.
  • Page 143 TL-WR702N 150Mbps Wireless N Nano Router Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis.
  • Page 144 Click the Upgrade button. Note: New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Router rather than the configuration, you can try to upgrade the firmware.
  • Page 145 TL-WR702N 150Mbps Wireless N Nano Router 7.8.4 Backup & Restore Choose menu “System Tools → Backup & Restore”, and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 7-20.
  • Page 146 TL-WR702N 150Mbps Wireless N Nano Router • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defaults (system will reboot automatically).
  • Page 147 TL-WR702N 150Mbps Wireless N Nano Router 7.8.7 System Log Choose menu “System Tools → System Log”, and then you can view the logs of the Router. Figure 7-23 System Log Refresh - Refresh the page to show the latest log list.

  • Page 148: Chapter 8. Configuration For Client Mode

    Chapter 8. Configuration for Client Mode This chapter will show each Web page's key functions and the configuration way for Client Mode of TL-WR702N. 8.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility.

  • Page 149: Quick Setup

    TL-WR702N 150Mbps Wireless N Nano Router Figure 8-2 Status Firmware Version - The version information of the Router’s firmware. Hardware Version - The version information of the Router’s hardware. LAN - This field displays the current settings or information for the LAN, you can configure them in the Network >...

  • Page 150: Working Mode

    TL-WR702N 150Mbps Wireless N Nano Router 8.4 Working Mode The Router supports five operation mode types: AP, Router, Repeater, Bridge and Client. Please select one your want. Click Save to save your choice, which is shown as Figure 8-3. Figure 8-3 Working Mode AP - The wireless access point mode.

  • Page 151: Wireless

    TL-WR702N 150Mbps Wireless N Nano Router 8.5.1 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 8-6 LAN MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can't be changed.
  • Page 152 TL-WR702N 150Mbps Wireless N Nano Router Figure 8-8 Wireless Settings - Client SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address).

  • Page 153: Dhcp

    TL-WR702N 150Mbps Wireless N Nano Router Be sure to click the Save button to save your settings on this page. Note: The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For best results, place your Router.
  • Page 154 TL-WR702N 150Mbps Wireless N Nano Router Figure 8-10 DHCP Settings DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.
  • Page 155 TL-WR702N 150Mbps Wireless N Nano Router Note: To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 8.7.2 DHCP Clients List Choose menu “DHCP → DHCP Clients List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 8-11.
  • Page 156 TL-WR702N 150Mbps Wireless N Nano Router Figure 8-12 Address Reservation MAC Address - The MAC address of the PC for which you want to reserve an IP address. Reserved IP Address - The IP address reserved for the PC by the Router.

  • Page 157: System Tools

    TL-WR702N 150Mbps Wireless N Nano Router Click the Next button to go to the next page and Click the Previous button to return the previous page. System Tools Figure 8-14 The System Tools menu Choose menu “System Tools”, and then you can see the submenus under the main menu: Diagnostic, Firmware, Factory Defaults, Backup &...
  • Page 158 TL-WR702N 150Mbps Wireless N Nano Router Figure 8-15 Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway.
  • Page 159 TL-WR702N 150Mbps Wireless N Nano Router Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis.
  • Page 160 Click the Upgrade button. Note: New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Router rather than the configuration, you can try to upgrade the firmware.
  • Page 161 TL-WR702N 150Mbps Wireless N Nano Router 8.8.4 Backup & Restore Choose menu “System Tools → Backup & Restore”, and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 8-19.
  • Page 162 TL-WR702N 150Mbps Wireless N Nano Router • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defaults (system will reboot automatically).
  • Page 163 TL-WR702N 150Mbps Wireless N Nano Router 8.8.7 System Log Choose menu “System Tools → System Log”, and then you can view the logs of the Router. Figure 8-22 System Log Refresh - Refresh the page to show the latest log list.

  • Page 164: Appendix A: Faq

    TL-WR702N 150Mbps Wireless N Nano Router Appendix A: FAQ How do I configure the Router to access the Internet by ADSL users? First, configure the ADSL Modem configured in RFC1483 bridge model. Connect the Ethernet cable from your ADSL Modem to the WAN port on the Router. The telephone cord plugs into the Line port of the ADSL Modem.
  • Page 165 TL-WR702N 150Mbps Wireless N Nano Router How do I configure the Router to access the Internet by Ethernet users? Log in to the Router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “Dynamic IP” for "WAN Connection Type", finish by clicking Save.
  • Page 166 TL-WR702N 150Mbps Wireless N Nano Router Figure A-4 Virtual Servers Figure A-5 Add or Modify a Virtual server Entry Note: Your opposite side should call your WAN IP, which is displayed on the “Status” page. How to enable DMZ Host: Log in to the Router, click the “Forwarding” menu on the left of your browser, and click "DMZ"...
  • Page 167 TL-WR702N 150Mbps Wireless N Nano Router Because the WEB Server port 80 will interfere with the WEB management port 80 on the Router, you must change the WEB management port number to avoid interference. To change the WEB management port number: Log in to the Router, click the “Security”...
  • Page 168 TL-WR702N 150Mbps Wireless N Nano Router Figure A-9 Add or Modify a Virtual server Entry The wireless stations cannot connect to the Router. Make sure the "Enable Wireless Router Radio" is checked. Make sure that the wireless stations' SSID accord with the Router's SSID.

  • Page 169: Appendix B: Configuring The Pc

    TL-WR702N 150Mbps Wireless N Nano Router Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary.
  • Page 170 TL-WR702N 150Mbps Wireless N Nano Router Figure 0-2 The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. Now you have two ways to configure the TCP/IP protocol below: Setting IP address automatically...
  • Page 171 TL-WR702N 150Mbps Wireless N Nano Router Figure 0-3 Note: For Windows 98 OS or before, the PC and Router may need to be restarted. Setting IP address manually Select Use the following IP address radio button. And the following items available If the Router's LAN IP address is 192.168.0.254, specify the IP address as 192.168.0.x (x is...
  • Page 172 TL-WR702N 150Mbps Wireless N Nano Router Now: Click OK to keep your settings. - 166 -...

  • Page 173: Appendix C: Specifications

    TL-WR702N 150Mbps Wireless N Nano Router Appendix C: Specifications General Standards IEEE 802.11n, 802.11b, 802.11g Protocols TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP Port One 10/100Mbps LAN/WAN port, one USB port 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m)

  • Page 174: Appendix D: Glossary

    TL-WR702N 150Mbps Wireless N Nano Router Appendix D: Glossary 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding.
  • Page 175 TL-WR702N 150Mbps Wireless N Nano Router PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection. SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network.

Table of Contents