Master Code Description; Arming - DSC LCD-600 Instruction Manual

Master Code
The four digit Master Code is used for arming and disarming the security system,
programming additional security codes and changing other features. The Master
Code will be supplied to you by your installer. If enabled by your installer, the
Master Code can be changed at any time. (See Programming Security Codes
section.)

Arming

If this display is showing, check to see that all zones are secure
Secure System
Before Arming < >
by closing all doors/windows and stopping motion in areas
covered by motion detectors. If a zone will not clear, it may be bypassed to allow
partial arming. Note: A bypassed zone reduces your protection. If a zone
cannot be cleared, call your installer for service.
Enter Code to
If this display is showing, check to see that the system is clear
Arm System
of troubles and that there are no zones bypassed. The system
< >
may be armed with zones bypassed and/or trouble conditions present but to do so
will compromise protection. Check to see which zones are bypassed and that
these zones are intentionally bypassed. If a trouble is present, see the section
"Viewing Trouble Conditions".
If this display is showing, there are no troubles or bypassed
Enter Code to
Arm System
zones and the system may be fully armed. To arm the system,
enter your four digit security code. The keypad sounder will beep as each digit is
entered. If the security code was incorrectly entered, the keypad sounder will beep
steadily for two seconds and the display will not change.
Once the correct security code has been entered, the display
Exit Delay in
Progress
will be as shown on the left. Exit the premises through the door
indicated by your installer as the "exit-entry" door. Once the "exit" delay expires,
the system will be armed and will display the following message
Enter Code to
Disarm System
If you enter your security code with one or more zones bypassed, the following
message will appear as soon as you enter the first digit.
WARNING If this message appears, ensure that the zones bypassed are
Bypass Active
intentionally bypassed.
If you enter your security code and a system trouble is present, the following
message will appear as soon as you enter the first digit.
If this message appears, check to see what the trouble
WARNING
condition System Trouble is and call for service. See the section "Viewing Trouble
Conditions".
If you arm the system with a zone bypassed or with a trouble present your
security protection is reduced.
4
Programming Security Codes
Master Code
The installer can program the system so that the Master Security Code can be
changed by the user. If your system is set up to allow a changeable Master Code,
follow the instructions below.
Start in the "Disarmed" mode and press the [ ] key to enter the "functions" list.
Scroll < > to..
Press (5) for...
Access Codes
Display will read..
Enter Master
Access Code...
Display will read..
Select Code< >
Code 1
or..
Select Code< >
Code 01
Display will read..
Enter 4 Digit
Access Code...
Enter the new Master Code. The Master Code must be 4 digits. Enter digits 0
through 9 only. Once the new code is entered the keypad sounder will beep 3
times and the display will read..
Select Code < >
Code 01
Press [#] to exit.
Remember to record your new Master Code on the System Information page in this
booklet.
Additional Codes
• PC1500 and PC1550 Control Panels
Up to 5 additional user codes (2 through 6) may be programmed. The 6th user
code can be made a One Time use code by your installer.
• PC2500 Control Panel
Up to 7 additional user codes (2 through 8) may be programmed. The 8th user
code can be made a One Time use code by your installer.
• PC 2550 and 3000 Control Panels
Up to 15 additional user codes (2 through 16) may be programmed. The 16th
user code can be made a One Time use code by your installer.
To erase, add or change a user code, press [ ] to enter the "functions" list.
Scroll < > to..
Press (5)
Access Code...
Display will read..
Enter Master
Access Code...
Display will read
Select Code < >
Code (x)
Press [5].
Enter your current Master Code.
Enter "1" for PC2550, PC2500, PC1550
and PC1500 systems.
P
Enter "01" for PC3000 system.
P
P
Press [5].
Enter Master Code.
or
Select code < >
Code (xx)
13