Installation and User Guide
ThinkServer TS200v
Machine Types: 0981, 0992, 1008, and 1010

Advertising

   Also See for Lenovo 098118U

   Summary of Contents for Lenovo 098118U

  • Page 1

    Installation and User Guide ThinkServer TS200v Machine Types: 0981, 0992, 1008, and 1010...

  • Page 3

    ThinkServer TS200v Types 0981, 0992, 1008, and 1010 Installation and User Guide...

  • Page 4

    First Edition (March 2010) © Copyright Lenovo 2010. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.

  • Page 5: Table Of Contents

    EU-EMC Directive (2004/108/EC) EN 55022 class Starting the Setup Utility program . . 49 B Statement of Compliance . . 70 Viewing and changing settings . . 49 Japanese VCCI Class B statement . . 71 Using passwords . 50 © Copyright Lenovo 2010...

  • Page 6: Table Of Contents

    20 A per phase . . 71 Japanese recycling statement. . 75 Federal Communications Commission (FCC) and Collecting and recycling a disused Lenovo telephone company requirements . . 71 computer or monitor . . 75 Canadian Department of Communications Disposing of Lenovo computer components .

  • Page 7

    Vor der Installation dieses Produkts die Sicherheitshinweise lesen. Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza. Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet. Antes de instalar este produto, leia as Informações sobre Segurança. © Copyright Lenovo 2010...

  • Page 8

    Antes de instalar este producto, lea la información de seguridad. Läs säkerhetsinformationen innan du installerar den här produkten. Important: Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English-language caution or danger statement with translated versions of the caution or danger statement in the Safety Information book.

  • Page 9

    Statement 1: DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet. v Connect to properly wired outlets any equipment that will be attached to this product.

  • Page 10

    Statement 2: CAUTION: When replacing the lithium battery, use only the battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.

  • Page 11

    Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.

  • Page 12

    Statement 4: ≥ 18 kg (39.7 lb.) ≥ 32 kg (70.5 lb.) ≥ 55 kg (121.2 lb.) CAUTION: Use safe practices when lifting. Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device.

  • Page 13

    Statement 8: CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components.

  • Page 14

    CAUTION: The following label indicates a hot surface nearby. Statement 13: DANGER Overloading a branch circuit is potentially a fire hazard and a shock hazard under certain conditions. To avoid these hazards, ensure that your system electrical requirements do not exceed branch circuit protection requirements. Refer to the information that is provided with your device for electrical specifications.

  • Page 15

    CAUTION: The battery is a lithium ion battery. To avoid possible explosion, do not burn the battery. Exchange it only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations. Attention: This product is suitable for use on an IT power distribution system whose maximum phase to phase voltage is 240 V under any distribution fault condition.

  • Page 16

    Installation and User Guide...

  • Page 17: Chapter 1. Introduction

    Chapter 1. Introduction ® This Installation and User Guide is intended to be used with your Lenovo ™ ThinkServer TS200v (Machine Types 0981, 0992, 1008, and 1010) server. This document contains information about: v Setting up and cabling the server...

  • Page 18: Notices And Statements In This Document

    Notices and statements in this document The caution and danger statements that appear in this document are also in the multilingual Safety Information document, which is on the Lenovo ThinkServer Documentation DVD. Each statement is numbered for reference to the corresponding statement in the Safety Information document.

  • Page 19: Related Documentation

    Related documentation The Lenovo ThinkServer Documentation DVD contains documentation for the server in Portable Document Format (PDF). The Lenovo ThinkServer Documentation DVD ® ® requires the Adobe Reader 5.0 (or later) or xpdf, which comes with Linux operating systems. The following table describes the content and location of documentation that is provided with your server.

  • Page 20

    Installation and User Guide...

  • Page 21: Chapter 2. Server Setup Roadmap

    Configure RAID “Configuring RAID” on page 52 Check for firmware Go to http://www.lenovo.com/support and go to the Downloads updates and Drivers section for this product. Install operating “Using the ThinkServer EasyStartup program” on page 56...

  • Page 22

    Installation and User Guide...

  • Page 23: Chapter 3. What Is Included With Your Server

    Chapter 3. What is included with your server The TS200v server package includes the server, a power cord, the ThinkServer Documentation DVD, and software media. Server Power cord Documentation and software media © Copyright Lenovo 2010...

  • Page 24: Features And Specifications

    (Kensington lock) v Intel Active Management Technology v For a list of supported microprocessors, v Support for a padlock (AMT) see http://www.lenovo.com/ v Trusted Platform Module (TPM) v Intel Hyper-Threading technology (some thinkserver and click the Options tab. models) Preinstalled operating system...

  • Page 25: Software, Easystartup, Easymanage

    Non-operating: -10° to 60°C (14° to 140°F) (without package) Software Lenovo provides software to help get your server up and running. EasyStartup The ThinkServer EasyStartup program simplifies the process of installing supported Microsoft Windows operating systems and device drivers on your server.

  • Page 26

    Installation and User Guide...

  • Page 27: Chapter 4. Server Controls And Connectors, Front View

    Figure 1 shows the locations of the controls and connectors on the front of your server. Figure 1. Front control and connector locations 1 Hard disk drive activity LED 3 Power switch 2 Power-on LED 4 USB connectors (2) © Copyright Lenovo 2010...

  • Page 28: Rear View

    Rear view Figure 2 shows the locations of the connectors on the rear of your server. Some connectors on the rear of your server are color-coded to help you determine where to connect the cables in your server. Figure 2. Rear connector locations 1 Power cord connector 7 Microphone connector 2 Serial port...

  • Page 29

    Connector Description Audio line-in connector Used to receive audio signals from an external audio device, such as a stereo system. When you attach an external audio device, a cable connects the audio line-out connector of the device to the audio line-in connector of the server. Audio line-out connector Used to send audio signals from the server to external devices, such as powered stereo speakers (speakers with built-in...

  • Page 30: System-board Internal Connectors

    System-board internal connectors Figure 3 shows the locations of the parts and connectors on the system board. Figure 3. System board connector locations 1 4-pin power connector 11 eSATA connector 2 Microprocessor 12 Power fan connector 3 Microprocessor fan connector 13 Front panel connector 4 DIMM 2 14 Clear CMOS (Complementary Metal Oxide...

  • Page 31: Internal Components

    Internal components Figure 4 shows the locations of the various components in your server. To remove the server cover and access to the inside of the server, see “Removing the server cover” on page 18. Figure 4. Component locations 1 Heat sink and fan assembly 4 PCI card 2 Memory module 5 Rear fan assembly...

  • Page 32: Internal Drives

    Internal drives Internal drives are devices that your server uses to read and store data. You can add drives to your server to increase storage capacity and enable your server to read other types of media. Internal drives are installed in bays. In this manual, the bays are referred to as bay 1, bay 2, and so on.

  • Page 33: Chapter 5. Installing Or Replacing Customer Replaceable Units, Handling Static-sensitive Devices, Installing Or Replacing Hardware

    Do not open your server or attempt any repair before reading and understanding the “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support Notes: 1. Use only server parts provided by Lenovo. © Copyright Lenovo 2010...

  • Page 34: Installing External Options, Removing The Server Cover

    Do not open your server or attempt any repair before reading and understanding the “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support This section provides instructions on how to remove the server cover. CAUTION: Turn off the server and wait three to five minutes to let the server cool before removing the server cover.

  • Page 35: Removing And Reinstalling The Front Bezel

    “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support This section provides instructions on how to remove and reinstall the front bezel. To remove and reinstall the front bezel, do the following: 1.

  • Page 36: Installing Or Replacing A Pci Card

    “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a PCI card. Your server has two standard PCI card slots, one PCI Express x1 card slot, and one PCI Express x16 card slot.

  • Page 37

    To install or replace a PCI card, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2.

  • Page 38

    4. If you are installing a PCI card, remove the appropriate metal slot cover. If you are replacing an old PCI card, grasp the old card that is currently installed and gently pull it out of the slot. Figure 9. Removing a PCI card Note: The PCI card fits tightly into the card slot.

  • Page 39: Installing Or Replacing A Memory Module

    “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a memory module. Your server has four slots for installing or replacing memory modules. When installing or replacing a memory module, use the following guidelines: v Use DDR3 ECC UDIMMs for your server.

  • Page 40

    To install or replace a memory module, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2.

  • Page 41: Installing Or Replacing The Optical Drive

    “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace the optical drive. To install or replace an optical drive, do the following: 1.

  • Page 42

    v If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear of the optical drive, press the blue release button 1 , and then slide the optical drive out of the optical drive bay. Figure 14.

  • Page 43

    6. Slide the new optical drive into the optical drive bay from the front of the server until the optical drive snaps into position. Figure 16. Installing the optical drive 7. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 19.

  • Page 44: Installing Or Replacing The Secondary Hard Disk Drive

    Do not open your server or attempt any repair before reading and understanding the “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace the secondary hard disk drive.

  • Page 45

    4. Press the release button 1 to release the secondary hard disk drive cage and then lift the cage out of the chassis. Figure 19. Removing the secondary hard disk drive cage 5. Pull on the handle to release and remove the blue hard disk drive bracket from the hard disk drive cage.

  • Page 46

    7. Slide the new hard disk drive with the blue bracket into the secondary hard disk drive cage until it snaps into position. 8. Slide the hard disk drive cage with the new hard disk drive into the chassis until it is directly underneath the metal tab 1 . Figure 21.

  • Page 47: Replacing The Secondary Hard Disk Drive

    9. Press the hard disk drive cage downward until it snaps into position. Make sure that the hard disk drive cage is secured in the chassis. Figure 22. Installing the secondary hard disk drive 10. Continue at “Connecting a SATA drive” on page 27. Replacing the secondary hard disk drive Note: Depending on the model type, your server might have a secondary hard disk drive installed.

  • Page 48: Replacing The Power Supply Assembly

    “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support This section provides instructions on how to replace the power supply assembly. To replace the power supply assembly, do the following:...

  • Page 49

    8. Install and tighten the four screws to secure the new power supply assembly. Note: Use only screws provided by Lenovo. 9. Connect the new power supply assembly cables to the system board and each of the drives. See “System-board internal connectors” on page 14.

  • Page 50: Replacing The Heat Sink And Fan Assembly

    Do not open your server or attempt any repair before reading and understanding the “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support This section provides instructions on how to replace the heat sink and fan assembly.

  • Page 51

    6. Follow this sequence to remove the four screws that secure the heat sink and fan assembly to the system board: a. Partially remove screw 1 , then fully remove screw 2 , and then fully remove screw 1 . b.

  • Page 52: Replacing The Primary Hard Disk Drive

    “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support This section provides instructions on how to replace the primary hard disk drive. To replace the primary hard disk drive, do the following: 1.

  • Page 53

    5. Press the blue release tab 1 downward, slide the hard disk drive cage 2 to the rear of the server, and then pivot it outward to completely remove the drive cage from the chassis. Then, pull on the blue handle 3 to release and remove the hard disk drive from the drive cage.

  • Page 54

    7. To install a new hard disk drive into the blue bracket, flex the sides of the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive.

  • Page 55

    9. Align the hard disk drive cage pivot pin with the slot 1 in the upper drive cage, as shown in Figure 28. Then, slide the hard disk drive cage into the chassis. 10. Press down on the metal latch 2 and pivot the hard disk drive cage into place.

  • Page 56: Replacing The Front Fan Assembly

    “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support Depending on the model type, your server might have a front fan assembly installed. This section provides instructions on how to replace the front fan assembly.

  • Page 57

    5. Release the two tabs 1 that attach the front fan assembly to the chassis as shown and then completely remove the front fan assembly from the chassis. Figure 29. Removing the front fan assembly Chapter 5. Installing or replacing customer replaceable units...

  • Page 58

    6. Insert the two tabs 2 of the new front fan assembly into the corresponding holes in the chassis, and press the other two tabs 1 through the holes until the front fan assembly is secured in place. Figure 30. Installing the front fan assembly 7.

  • Page 59: Replacing The Rear Fan Assembly

    “Safety” on page v and the Safety Information book. To obtain a copy of the Safety Information book, go to: http://www.lenovo.com/support This section provides instructions on how to replace the rear fan assembly. To replace the rear fan assembly, do the following: 1.

  • Page 60: Completing The Parts Replacement

    7. Carefully pull on the tips of the rubber mounts until the new rear fan assembly is secured in place. Figure 32. Installing the rear fan assembly 8. Connect the new rear fan assembly cable to the system fan connector on the system board.

  • Page 61: Updating The Server Configuration

    Setup Utility program. Refer to Chapter 6, “Configuring the server,” on page 49. Note: In most areas of the world, Lenovo requires the return of the defective Customer Replaceable Unit (CRU). Information about this will come with the CRU or will come a few days after the CRU arrives.

  • Page 62: Installing Security Features, Integrated Cable Lock

    The cable lock also locks the buttons used to remove the server cover. This is the same type of lock used with many notebook computers. You can order an integrated cable lock directly from Lenovo by searching for Kensington at: http://www.lenovo.com/support...

  • Page 63: Padlock, Password Protection, Erasing Lost Or Forgotten Passwords (clearing Cmos)

    Padlock Your server is equipped with a padlock loop so that the cover cannot be removed when a padlock is installed. Figure 35. Installing a padlock Password protection To deter unauthorized use of your server, you can use the Setup Utility program to set a password.

  • Page 64

    5. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and pin 3). 6. Reinstall all parts and reconnect all cables that have been removed. 7. Reinstall the server cover and reconnect the server power cord. See “Completing the parts replacement”...

  • Page 65: Chapter 6. Configuring The Server, Using The Setup Utility Program, Starting The Setup Utility Program

    “Starting the Setup Utility program.” Then, follow the instructions on the screen. When working with the Setup Utility program menu, you must use the keyboard. The keys used to perform various tasks are displayed at the bottom of each screen. © Copyright Lenovo 2010...

  • Page 66: Using Passwords

    Using passwords By using the Setup Utility program, you can set passwords to prevent unauthorized access to your server and data. The following types of passwords are available: v Power-On Password v Administrator Password v Hard Disk Password You do not have to set a password to use your server. However, using passwords improves computing security.

  • Page 67: Enabling Or Disabling A Device, Selecting A Startup Device

    4. Follow the instructions on the right side of the screen to set, change, or delete a password. Note: A password can be any combination of up to 64 alphabetic and numeric characters. For more information, see “Password considerations” on page 50. Enabling or disabling a device This section provides information on how to enable or disable user access to the following devices:...

  • Page 68: Advanced Settings, Exiting From The Setup Utility Program, Configuring Raid

    Viewing or changing the startup device sequence This section provides instructions on how to view or permanently change the configured startup device sequence. To view or permanently change the configured startup device sequence, do the following: 1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 49.

  • Page 69: Raid Level, Configuring The System Uefi To Enable Sata Raid Functionality, Creating Raid Volumes

    RAID Level Your server must have the minimum number of SATA hard disk drives installed for the supported level of RAID below: v RAID Level 0 – Striped disk array – Two hard disk drives minimum – Better performance without fault tolerance v RAID Level 1 –...

  • Page 70: Deleting Raid Volumes, Updating System Programs, Using System Programs

    10. Press Y when prompted to confirm the exit. Deleting RAID volumes This section describes how to use the Intel Matrix Storage Manager option ROM configuration utility to delete RAID volumes. To delete RAID volumes, do the following: 1. Press Ctrl+I when prompted to enter the Intel Matrix Storage Manager option ROM configuration utility during the server startup.

  • Page 71: Updating (flashing) The Uefi From A Disc, Updating (flashing) The Uefi From Your Operating System

    Lenovo might make changes and enhancements to the POST and UEFI. When updates are released, they are available as downloadable files on the Lenovo Web site at http://www.lenovo.com. Instructions for using the POST/UEFI updates are available in a TXT file that is included with the update files. For most models, you can download either an update program to create a system-program-update (flash) disc or an update program that can be run from the operating system.

  • Page 72: Recovering From A Post/uefi Update Failure, Using The Thinkserver Easystartup Program

    3. Print these instructions. This is very important because they are not on the screen after the download begins. 4. Follow the printed instructions to download, extract, and install the update. Recovering from a POST/UEFI update failure If power to your server is interrupted while the POST/UEFI is being updated (flash update), your server might not restart correctly.

  • Page 73

    The program is contained on the ThinkServer EasyStartup DVD provided with your server. If you did not receive the DVD with your server, you can download an ISO image of the DVD from http://www.lenovo.com/support. The program has a built-in help system and User Guide to answer questions you might have. The...

  • Page 74: Installing Thinkserver Easymanage Agent

    1. Insert the ThinkServer EasyStartup DVD and restart the server. If the EasyStartup program does not start, see “EasyStartup problems” on page 60. 2. Follow the instructions on the screen until you get to the Start option screen. 3. When the Start option screen is displayed, do the following: a.

  • Page 75: Chapter 7. Troubleshooting And Diagnostics, Basic Troubleshooting, General Problems

    Note: If you cannot correct the problem, have the server serviced. For a list of service and support telephone numbers, refer to the Warranty and Support Information document available on the ThinkServer Documentation DVD or go to the Lenovo Support Web site at: http://www.lenovo.com/support/phone General problems The following table describes the general problems and suggested actions to correct detected problems.

  • Page 76: Easystartup Problems, Pc-doctor For Dos, Creating A Diagnostic Disc

    PC-Doctor for DOS You can also download the latest version of the PC-Doctor for DOS diagnostic program from http://www.lenovo.com/support. The PC-Doctor for DOS diagnostic program runs independently of the Windows operating system. Use the PC-Doctor for DOS diagnostic program if you are unable to start the Windows operating system.

  • Page 77

    To run the diagnostic program from a diagnostic disc that you created, do the following: 1. Turn off your server. 2. Repeatedly press and release the F12 key when turning on the server. When the Please select boot device window displays, release the F12 key. 3.

  • Page 78

    Installation and User Guide...

  • Page 79: Chapter 8. Getting Help And Technical Assistance, Before You Call, Using The Documentation

    Chapter 8. Getting help and technical assistance If you need help, service, or technical assistance or just want more information about Lenovo products, you will find a wide variety of sources available from Lenovo to assist you. This chapter contains information about where to go for...

  • Page 80: Getting Help And Information From The World Wide Web, Calling For Service

    Getting help and information from the World Wide Web On the World Wide Web, the Lenovo Web site has up-to-date information about Lenovo systems, optional devices, services, and support. For general information about Lenovo products or to purchase Lenovo products, go to http://www.lenovo.com.

  • Page 81: Using Other Services, Purchasing Additional Services

    Service availability and service name might vary by country or region. For more information about these services, go to the Lenovo Web site at: http://www.lenovo.com/ Chapter 8. Getting help and technical assistance...

  • Page 82

    Installation and User Guide...

  • Page 83: Appendix. Notices

    Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk.

  • Page 84: Export Classification Notice, Television Output Notice, European Conformance Ce Mark, Trademarks

    Macrovision Corporation. Reverse engineering or disassembly is prohibited. European conformance CE mark Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo The Lenovo logo ThinkServer Microsoft, Windows, and Windows Server are trademarks of the Microsoft group of companies.

  • Page 85: Electronic Emissions Notices, Federal Communications Commission Declaration Of Conformity

    Consult an authorized dealer or service representative for help. Lenovo is not responsible for any radio or television interference caused by using other than specified or recommended cables or connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment.

  • Page 86: European Union Emc Directive Conformance Statement

    Grenzwerte der EN 55022 Klasse B ein. Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu betreiben. Des Weiteren dürfen auch nur von der Lenovo empfohlene Kabel angeschlossen werden. Lenovo übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung der Lenovo verändert bzw.

  • Page 87: Japanese Vcci Class B Statement, Federal Communications Commission (fcc) And Telephone Company Requirements

    You may attach the label to the exterior of the computer in which you install the Lenovo modem, or you may attach the label to the external DAA, if you have one. Place the label in a location that is easily accessible, should you need to provide the label information to the telephone company.

  • Page 88: Canadian Department Of Communications Certification Label, Power Cord Notice

    To avoid electrical shock, always use the power cord and plug with a properly grounded outlet. Power cords provided by Lenovo in the United States and Canada are listed by Underwriters Laboratories (UL) and certified by the Canadian Standards Association (CSA).

  • Page 89

    The cord set should have the appropriate safety approvals for the country in which the equipment will be installed. Power cords provided by Lenovo for a specific country or region are usually available only in that country or region.

  • Page 90: Polyvinyl Chloride (pvc) Cable And Cord Notice, Turkish Statement Of Compliance

    State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. Turkish statement of compliance The Lenovo product meets the requirements of the Republic of Turkey Directive on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (EEE).

  • Page 91: European Union (eu) Weee Statement, Japanese Recycling Statement

    Collecting and recycling a disused Lenovo computer or monitor If you are a company employee and need to dispose of a Lenovo computer or monitor that is the property of the company, you must do so in accordance with the Law for Promotion of Effective Utilization of Resources. Computers and monitors are categorized as industrial waste and should be properly disposed of by an industrial waste disposal contractor certified by a local government.

  • Page 92: Disposing Of Disused Lithium Batteries From Lenovo Computers, Energy Star Model Information

    If you want to replace it with a new one, contact your place of purchase or ask for a repair service provided by Lenovo. If you have replaced it by yourself and want to dispose of the disused lithium battery, insulate it with vinyl tape, contact your place of purchase, and follow their instructions.

  • Page 93: Index

    Ethernet connector 13 exiting, Setup Utility 52 external options, installing 18 padlock loop 47 parts replacement, completing 44 password failure, recovering from POST/UEFI 56 Administrator 50 features 8 considerations 50 flashing UEFI 55 Power-On Password 50 © Copyright Lenovo 2010...

  • Page 94

    password (continued) system board setting, changing, deleting 50 connectors 14 password protection 47 locating parts 14 passwords locations 14 erasing 47 memory module 23 lost or forgotten 47 passwords, using 50 PCI card 20 installing, replacing 20 television output notice 68 slots 20 temporary startup device 51 power supply assembly, replacing 32...

  • Page 96

    Printed in USA...

Comments to this Manuals

Symbols: 0
Latest comments: