Safety IMPORTANT SAFETY INSTRUCTIONS Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a Warning or Caution based on the risk type. Definitions This is the safety alert symbol.
Safety SAFETY PRECAUTIONS WARNING WARNING WARNING WARNING WARNING • Read all instructions before using the appliance. • Improper installation, adjustment, alteration, service, or maintenance can cause personal injury or property damage. Refer to these instructions and the accompanying Use & Care Manual. For assistance or additional information, consult a qualified installer, service agency, manufacturer (dealer), or the gas supplier.
Page 4
Safety WARNING WARNING WARNING WARNING WARNING • Based on safety considerations, the top burner flame should be adjusted so it does not extend beyond the edge of the cooking utensil. • If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.
Finding Information TABLE OF CONTENTS Safety ..............2 Definitions ............2 Important Safety Instructions ......2 Safety Precautions ..........3 Finding Information ........... 5 Please Read And Save This Guide ....5 Questions? ............5 Table Of Contents ..........6 Preparing for Installation ........
Preparing for Installation ELECTRICAL POWER SUPPLY REQUIREMENTS It is the owner’s responsibility to ensure that the electrical connection of this appliance is performed by a qualified electrician. The electrical installation, including minimum supply wire size and grounding, must be in accordance with the National Electric code ANSI/NFPA 70- 1993* (or latest revision) and local codes and ordinances.
Preparing for Installation GAS AND ELECTRICAL ROUGH-IN Locations NOTE The shaded areas shown in the illustrations, denote the location of the gas stub and the electrical junction box/receptacle. These are suggested locations. For replacement purposes, the location of the existing utilities may be utilized provided that they do not interfere with the sides or rear of the range.
Preparing for Installation CABINET AND COUNTERTOP PREPARATION NOTES • If cabinet storage space is to be provided directly above the range, the risk of personal injury may be reduced by installing a ventilating hood that projects horizontally a minimum of 5 inches beyond the face of the cabinets. •...
Page 11
Preparing for Installation Plan the installation so that the electrical connection, gas shut-off valve, and pressure regulator are accessible from the front of the cabinet. Figure 1 E30DF74EPS, E36DF76EPS and E48DF76EPS Cutout Dimensions Model “A” “B” E30DF74EPS 36” (914mm) Recommended 30 1/16”...
Preparing for Installation INSTALLING THE ANTI-TIP BRACKET (FOR 30”, 36” & 48” MODELS) WARNING WARNING WARNING WARNING WARNING The 30”, 36” and 48” ranges require an anti-tip device. Before installing the range, you must locate and secure the anti-tip bracket to the floor. Installation of E30DF74EPS Anti-Tip Bracket Figure 4 Top View...
Page 14
Preparing for Installation INSTALLING THE ANTI-TIP BRACKET (FOR 30”, 36” & 48” MODELS) WARNING WARNING WARNING WARNING WARNING The 30”, 36” and 48” ranges require an anti-tip device. Before installing the range, you must locate and secure the anti-tip bracket to the floor. Installation of E36DF76EPS Anti-Tip Bracket Figure 6 Top View...
Page 15
Preparing for Installation INSTALLING THE ANTI-TIP BRACKET (FOR 30”, 36” & 48” MODELS) WARNING WARNING WARNING WARNING WARNING The 30”, 36” and 48” ranges require an anti-tip device. Before installing the range, you must locate and secure the anti-tip bracket to the floor. Installation of E48DF76EPS Anti-Tip Bracket Top View Figure 8...
Installation INSTALLING THE 30”, 36” & 48” RANGE OPTIONAL BACKGUARDS Your Electrolux Icon range was shipped with a backguard in place. These instructions cover the installation of one of the optional backguards. WARNING WARNING WARNING WARNING WARNING Be sure that the range is not connected to gas or power before proceeding.
Installation REMOVING THE OVEN DOOR(S) WARNING WARNING WARNING WARNING WARNING Do not attempt to disengage the hinge catches with the door removed from the oven. The hinge springs could release causing personal injury. Do not lift or carry the oven door by the door handle. Open the door to its fully opened position.
Installation MAKING THE ELECTRICAL CONNECTION WARNING WARNING WARNING WARNING WARNING • Models E30DF74EPS, E36DF76EPS and E48DF76EPS must be connected to a grounded, metallic, permanent wiring system. Alternatively, a grounding conductor should be connected to the grounding terminal or lead on the appliance.
Page 20
Installation WARNING WARNING WARNING WARNING WARNING Do not connect the green appliance wire to the neutral (white) supply wire unless local building codes permit. Connecting the Green Appliance Wire to the Neutral (White) Supply Wire – Where Local Codes Permit Connect the green and white appliance wires to the neutral (white) supply wire in the junction box.
Page 21
Installation Connecting the Green Appliance Wire to a Grounded Supply Wire or a Grounded Cold Water Pipe – Where Local Codes Permit. Separate the green and white appliance wires. Connect the white appliance wire to the neutral (white) supply wire in the junction box.
Installation MAKING THE GAS CONNECTION Before sliding the range into the cabinet, connect a flexible gas connector to the gas shut-off valve previously installed on the stub out. The gas valve must be turned off during installation. Connect the flex connector to the pipe fitting at the right rear of the range.
Installation INSTALLING THE RANGE Measure from the floor to the countertop and adjust the leveling legs as required to position the top frame at the desired height, based on the cabinet and countertop installation. Carefully slide the range into position in the cutout. The rear anti-tip leg should engage the anti-tip bracket.
Check the electrical connections and gas supply to ensure that the installation has been completed correctly. • If the appliance still does not work, contact an authorized service company. Do not attempt to repair the appliance yourself. Electrolux is not responsible for service required to correct a faulty installation.
Page 25
Professional series Liquid Petroleum Gas (LPG) Conversion Kit Instructions Freestanding Range Models: E30DF74EPS, E36DF76EPS, E48DF76EPS Model E30DF74EPS shown WARNING: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction.
Page 26
STEP 1 Prepare Required Tools 1/8” flat blade screwdriver Thread-locker (Loctite 242 or equivalent) Needle-nose pliers Burner ring removal tool (provided with conversion kit) 10 mm open end wrench U-tube manometer (calibrated) 6” and 8” long adjustable wrenches Leak detector: Gas or bubble forming fluid 6”...
Page 27
Professional Series Range LPG Conversion Kit LPG Kit Parts Lists LPG Conversion Kit for Models E36DF76EPS and E48DF76EPS (36 and 48-Inch) Kit Part Number: 700147-1 Part Number Description Quantity 65481 BAG, PLASTIC 65480 LABEL, CONVERSION INFORMATION 86007 TOOL, REMOVAL, BUNRER RING 65558 INSTALLATION INSTRCTIONS, LPG CONVERSION KIT 76125*...
Page 28
STEP 3 Prepare Range for Conversion 3-1 Move the range out from the wall, if necessary. 3-4 Remove the grates from the cooktop. 3-2 If the range is connected to a natural gas supply 3-5 Remove all of the burner caps and burner rings line, close the gas supply valve.
Page 29
Professional Series Range LPG Conversion Kit STEP 5 Disassemble Cooktop 5-1 Insert the large end of the burner ring removal 5-3 Repeat steps 5-1 and 5-2 for the remaining tool into the top of the left rear burner head. burners. Unscrew and remove the nut.
Page 30
STEP 6 Replace Bypass Orifices 6-1 Make sure all knobs are in the off position. the burner location. The bypass orifice size is stamped on its head. 6-2 Remove all of the burner knobs from the front of the range. 6-5 Insert the bypass orifice and the attached o-ring into the right side of the valve with the needle 6-3 Insert the 1/8”...
Page 31
Professional Series Range LPG Conversion Kit STEP 7 Replace Main Orifices 7-1 Remove the two screws that hold the left rear 7-4 Replace the main orifice with the appropriate burner base to the stove chassis. size from Table 7-1. Match both the model number and the burner location.
Page 32
STEP 8 Perform Pressure Tests 8-1 Connect the U-tube manometer to the LPG 8-5 Make sure all knobs on the front of the range supply line. are in the off position. 8-2 With electrical power to the range disconnected, 8-6 Connect the U-tube manometer to the left rear open the LPG supply valve.
Page 33
Professional Series Range LPG Conversion Kit Burner E30DF74EPS E36DF76EPS E48DF76EPS Location (30-Inch) (36-Inch) (48-Inch) Left Rear HN A-0053-E HN A-0053-E HN A-0053-E Left Front HN A-0052-E HN A-0052-E HN A-0052-E Right Rear HN A-0053-E HN A-0052-E HN A-0052-E Right Front HN A-0053-E HN A-0053-E HN A-0053-E...
Page 34
STEP 10 Perform Leak Tests 10-1 Make sure that all knobs on the front of the 10-4 Re-assemble the burner heads, burner head range are in the off position. nuts, burner rings, and burner caps without the spill tray in place. Be sure the igniter wire is 10-2 With electrical power to the range disconnected, connected to each burner head.
Page 35
Figure 12-1 Conversion Label Altitude Considerations The Electrolux Professional Series range is equipped with two types of burners: Sealed power burners – up to 17,000 BTU per hour Sealed precision burner(s) – up to 8500 BTU per hour (smaller in size than the power burner) For elevations above 2000 feet, the burners ratings will be reduced at the rate of 4% for each 1000 feet above sea level.
Page 36
.38/9.7 Center Front HN A-0053-E .37/9.5 Model E48DF76EPS (48-Inch) The Electrolux Group USA • 250 Bobby Jones Expressway • Augusta, GA 30907 1-877-4electrolux (1-877-453-3287) • www.electroluxusa.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 1-800-688-4606 • www.electroluxca.com...