Advertisement
Quick Links
PATLITE@
Notice
to Customer
Thank you very much for purchasing our PATLITE
product.
Request the installation and wiring be performed by a
professional contractor if construction work is
involved.
Prior to installation, read this manual thoroughly
before using this product to ensure correct use.
After reviewing this manual, if there are any
questions regarding this product, please contact the
nearest
PATLITE
office listed on the back cover of
this
manual.
Notice
to Contractor
Read this manual carefully prior to installation.
Be sure to return this manual
to the customer.
SIGNAL
I—LS7
Model
LED SIGNAL
TOWER
INSTRUCTION MANUAL
[ Maintenance Version ]
I
Safety Precautions
2
Model Number Configuration
3
Part N ames andOuter A ppearance 15
4
Stackable T owerConstruction 16
5
Block
Diagram
6
Installation
7
Wiring
8
Volume Adjustment
9
Post-installation
10 Inspection
11 Troubleshooting
12 Specifications
13 ReplacementParts
14 Option Parts
TOWER
Page
14
15
16
17
19
21
Relocation
21
21
22
22
23
23
Advertisement
Related Manuals for Patlite LS7
Summary of Contents for Patlite LS7
- Page 1 Stackable T owerConstruction 16 Block Diagram Installation Wiring Volume Adjustment Notice to Customer Thank you very much for purchasing our PATLITE Post-installation Relocation product. Request the installation and wiring be performed by a 10 Inspection professional contractor if construction work is involved.
- Page 2 Safety Precautions Safety Precautions Failure t oobserve the following may r esult indeath o rserious injury. Request the installation and TO prevent from short-circuits, wiring be performed by a electric shock or damage, LISENCE professional contractor observe the following: construction work is involved.
- Page 3 Model Number Configuration RatedBodyLighting Buzzer Mounting Wiring Model color Tiers Voltage Color LS7- -RYGBC Model 5 LED Tiers Common all models LED colors in order from top to bottom: red, yellow, green, Rated Voltage : 24 v blue white. (None...
- Page 4 Stackable Tower Construction What a 'Stackable Structure'? The 'stackable structure' is a feature which allows the main signal tower unit and the outer cover to be separated with just a single touch. (Previous signal towers require tools to disassemble, such as removing screws.) The •stackable structure makes maintainance...
- Page 5 Installation A CAUTION The following requirements The buzzer is unidirectional, therefore it is most easily audible necessary for proper installation. in the buzzer source direction. Position the signal tower so that • Install the signal tower where the buzzer diaphram is facing excessive vibration...
- Page 6 Remove the signal tower from the mount. Attach the main unit to the mount. Pull out the lead wires. ( H Lead wire specifications) Main unit Mount Thread the wires through the wiring hole. Thread the lead wires through the mount and wiring hole, Refer to "...
- Page 7 Wiring WARNING Prior to wiring, ensure the power Verify the power supply voltage supply is disconnected from the and whether it is direct current signal tower. or alternating current. What voltage? CAUTION Never apply a voltage to the To protect the power supply and C o mrnon mashing wire "flashing common"...
- Page 8 Examples Wiring examples are shown in accordance to the signal tower model and external contact type. If the signal tower is being used under special conditions and there are any questions, contact our PATLITE office prior to performing any wiring.
- Page 9 8 Volume Adjustment The volume adjustmentof the buzzer is done by inserting a screwdriver into the volume adjustment Volume Adjustment Hole Buzzer case hole of the buzzer case. Referto " •Stackable TowerConstruction" (9 P.16) for details on removingthe buzzer case. Loud Seen from...
- Page 10 Ifthe problem is notcorrected, evenafterthe aboveremedies havebeenperformed, usethetablebelow to makedetailed notes of theproduct, i ts problem, a ndthencontact e itherthe placeofpurchase oryournearest P ATLITE SalesRepresentative. The place of purchase A PATLITE office (4 back cover) Product Details Purchase...
- Page 11 13 Replacement Parts Thefollowing are replacement partsavailable forthis product. F orfurtherdetails, r efertoour company website. Outer cover O-ring Mount cover (Note)When replacingtheouter cover,replacetheO-ringat thesame time. 14 Option Parts Thisproduct i ncludes thefollowingoptionparts.Fordetails, r efertoourcompany website. Platform Bracket Connector with cable (2m •...
- Page 12 01208386b 'FAX. http://www.patlite.co_jp http://www.patlite.co.jp The latest product information can be viewed on outcompany:s website. (Note) Dimensions, specifications andstructureare subject t o changefor improvement withoutnotice. Copyright 0 2011 PATLITE Corporation All Rights Reserved. 3432-A '1 1.4.UMC (Installation template) Do not write...
Need help?
Do you have a question about the LS7 and is the answer not in the manual?
Questions and answers